Protocols
How the buses and interfaces in your design work, where each one is used, and which tools capture, decode and drive it. Each page has wiring and timing diagrams, the faults engineers meet most often, and the protocol analysers, logic analysers and host adapters we supply for it.
On-Board Serial Buses
Chip-to-chip links on one board.
I2C
Two-wire bus for sensors, EEPROMs and power chips.
I3C
MIPI successor to I2C: push-pull, 12.5 MHz, in-band interrupts.
MIPI RFFE and SPMI
Two-wire MIPI control buses for RF front ends and power management ICs.
SMBus and PMBus
I2C with timeouts and error checking, for batteries and power supplies.
SPI
Four-wire, full-duplex bus for flash, ADCs and displays.
eSPI
Intel chipset link to embedded controllers and BMCs, replacing LPC.
UART
Asynchronous serial frames for consoles, modules and RS-232.
MDIO (Ethernet PHY Management)
Two-wire bus a MAC uses to configure Ethernet PHYs, Clause 22 and 45.
I2S, TDM, PDM and SoundWire
Board-level digital audio: I2S, TDM, PCM, PDM microphones and MIPI SoundWire.
1-Wire, HDQ and SDQ
Single-wire buses for sensors, ID chips and battery fuel gauges.
Debug and Programming Interfaces
How debuggers and programmers reach the silicon.
Automotive and Vehicle Networks
In-vehicle and machine networks.
Industrial Serial and Fieldbus
Long-distance and multi-drop serial links.
CAN
Multi-master differential bus for vehicles and industrial control, with CAN FD for larger, faster frames.
RS-232
Point-to-point serial link between equipment, with bipolar signal levels on D-sub connectors.
RS-485
Differential multi-drop serial bus for long cable runs, carrying Modbus RTU, BACnet MS/TP and DMX512.
Modbus, PROFIBUS and IO-Link
The everyday industrial protocols: Modbus RTU, ASCII and TCP, PROFIBUS DP and IO-Link.
MIL-STD-1553
Dual-redundant 1 Mbit/s command-response bus for military and aerospace avionics.
PC and Peripheral Interfaces
Links between a computer and its peripherals.
USB 2.0
Host-driven peripheral bus at 1.5, 12 and 480 Mbit/s, still present on every USB 3 port and USB-C data port.
SMBus and PMBus
I2C with timeouts and error checking, for batteries and power supplies.
USB 3
SuperSpeed USB at 5 Gbit/s and above, with separate transmit and receive pairs alongside USB 2.0.
USB Power Delivery
How a USB-C source and sink negotiate voltage and current over the CC line.
DDC, EDID, HDMI CEC and DisplayPort AUX
How a source reads a monitor's EDID, and the HDMI CEC and DisplayPort AUX links.
eSPI
Intel chipset link to embedded controllers and BMCs, replacing LPC.
LPC and Serial IRQ
The PC chipset bus to Super I/O, TPM, embedded controllers and BIOS flash.
PECI, SVID and SVI2/SVI3
Processor thermal and voltage-control links: Intel PECI and SVID, AMD SVI2 and SVI3.
Memory and Storage Interfaces
Flash, memory card and managed storage buses.
SD, SDIO and eMMC
Command, response and data lines of SD cards, SDIO modules and eMMC.
I3C
MIPI successor to I2C: push-pull, 12.5 MHz, in-band interrupts.
Flash Memory Buses
Quad and Octal SPI, SPI NAND, HyperBus and parallel ONFI NAND interfaces.
SPI
Four-wire, full-duplex bus for flash, ADCs and displays.
Lighting, Audio and Show Control
Entertainment and building control networks.
Protocols by Industry
Where each protocol is typically used. A protocol appears under every industry it serves.