Brushless Click Board

Download Files

Brushless Click Board

Product Description

The Brushless Click Board™ carries Toshiba's TB6575FNG IC for driving 3-phase full-wave Brushless DC motors — which are ideal for powering flying drones. The click is able to safely drive external motors with up to 32V/2A.

The board features three pairs of onboard screw terminals. VBAT is for connecting an external 7-32V DC power supply. The other two are for connecting an external motor.

PRECISION CONTROL

Brushless motors have a very long operating life and can be precisely controlled – the speed is adjusted by the amount of input voltage (higher voltage equals more speed).

The TB6575FNG IC controls the rotation speed by changing the PWM duty cycle.

MOSFET CHIPS

Two types of MOSFET chips on board switch the output on and off. This controls the voltage levels applied to the motor which in turn determines the speed and rotation of the motor shaft.

The Brushless Click Board™ communicates with the target board MCU over the PWM pin, as well as INT, AN and RST pins. The board is designed to use a 5V power supply only. See the documentation page for more details.

The Brushless Click Board™ is theoretically capable of outputting higher currents, however, in such a case the MOSFET chips have to be cooled down with an external cooler.

APPLICATIONS

Automotive industry, drones (because of the good power-to weight ratio of brushless motors), computers, medical equipment, HVAC systems, small home appliances, robotics, battery powered systems, small cooling fans in computers, toys, etc.

SPECIFICATIONS

MOTOR POSITION DETECTION ERROR

Position detection is synchronized with the PWM signal generated in the IC. When the IC is used in a high speed motor a position detection error relative to the PWM frequency may occur. The detection is performed on the falling edge of the PWM signal. An error is recognized when the pin voltage exceeds the reference voltage.

PINOUT DIAGRAM

This table shows how the pinout on the Brushless Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes	Pin					Pin	Notes
Measures the voltage of the DC power supply	VSENSE	1	AN	PWM	16	PWM	Duty cycle control
Motor direction	DIR	2	RST	INT	15	INT	Rotation speed sensing output
NC	3	CS	RX	14	NC
NC	4	SCK	TX	13	NC
NC	5	MISO	SCL	12	NC
NC	6	MOSI	SDA	11	NC
This click works on 5V only	NC	7	+3.3V	+5V	10	+5V	+5V power input
Ground	GND	8	GND	GND	9	GND	Ground

Software Support

1 void main() 
2 {
3  MCU_Init();
4  TFT_Init_ILI9341_8bit(320, 240);  // TFT Init
5   TFT_BLED = 1;
6   DrawFrame();
7   MOTOR_DIR = CCW;  // Setting motor direction to counter-clock-wise
8   while(1) {
9     if (GPIOD_IDR.B3) {                // button on PD3 pressed
10       Delay_ms(10);
11       current_speed = current_speed + STEP;   // increment current_duty
12       if (current_speed > pwm_period)       // if we increase current_duty greater then possible pwm_period value
13       {
14         current_speed = 0;                    // reset current_duty value to zero
15       }
16       PWM_TIM5_Set_Duty(current_speed,  _PWM_NON_INVERTED, _PWM_CHANNEL1);  // set newly acquired duty ratio
17      }
18     if (GPIOD_IDR.B6) {                // button on PD6 pressed
19       Delay_ms(10);
20       current_speed = current_speed - STEP;
21       if (current_speed > pwm_period)       // if we decrease current_duty greater then possible pwm_period value (overflow)
22       {
23           current_speed = pwm_period;          // set current_duty to value of pwm_period
24       }
25       PWM_TIM5_Set_Duty(current_speed,  _PWM_NON_INVERTED, _PWM_CHANNEL1); // set newly acquired duty ratio
26      }
27     Delay_ms(20);
28    // current_speed display
29     WordToStr(current_speed, txt);
30     TFT_Rectangle(150, 80, 250, 110);
31     TFT_Write_Text(txt, 150, 80);
32   }
33 }

Related Products