Skip to product information
1 of 7

Mikroelektronika d.o.o.

LED Driver 8 Click Board

LED Driver 8 Click Board

24-LED Driver with Programmable Brightness and Blinking
SKU: MIKROE-4268
Regular price
£11.60 inc VAT
£9.80 exc VAT
Regular price £14.00 GBP Sale price
£11.60 inc VAT
£9.80 exc VAT
Sale Sold out
Shipping calculated at checkout.
If no stock shown above, check availability
View full details

Overview

The LED Driver 8 Click Board™ is a compact add-on board optimized for dimming and blinking 32 mA RGBA LEDs. This board features the 24-channel SPI-compatible constant current LED driver from NXP Semiconductors. It has 24 LED output channels, a programmable group dimming/blinking mixed with individual LED brightness, and programmable LED output delay to reduce EMI and surge currents. It also possesses gradation control for all channels where all 24 constant current output channels can sink up to 32 mA, and tolerate up to 5.5 V in its OFF state. As the name itself says, this Click Board™, next to driving RGBA LEDs can be used for the purpose of LED Status signalization in LED displays, LED backlight, keypad backlights for cellular phones or handheld devices, and many more.

The LED Driver 8 Click Board™ is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click Board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.

How Does The LED Driver 8 Click Board™ Work?

The LED Driver 8 Click Board™ is based on the PCA9957, a daisy-chain SPI compatible 4-wire serial bus controlled 24-channel constant current LED driver optimized for dimming and blinking 32 mA RGBA LEDs from NXP Semiconductors. The PCA9957 has 24 internal 8-bit DACs with an operating frequency of 31.25 kHz and a duty cycle from 0% to 100% used to adjust brightness levels for each LED current source. Each LED output is programmable and can be turned off, on (with no PWM control), set at its individual PWM controller value, or both individual and group PWM controller values. Its output peak current is adjustable with an 8-bit linear DAC from 125 μA to 31.875 mA because of the R4 resistor of 2kΩ connected to the REXT pin.

LED Driver 8 Click Board™

Gradation control for all current sources is achieved through serial interface and allows the user to ramp current automatically without any help from the MCU. It has two operation modes for each group: Single-Shot Mode (output pattern once) and Continuous Mode (output pattern repeat). Each channel can be set to either Gradation Mode or Normal Mode and assigned to any one of six gradation control groups. These groups have four independent registers to control ramp-up and ramp-down rate, step time, hold ON/OFF time, and final hold ON output current.

The LED Driver 8 Click Board™ communicates with MCU through a daisy-chain SPI compatible 4-wire serial interface with a clock frequency up to 10 MHz. The input labeled as OE routed to the PWM pin on the mikroBUS™ blinks all the LED outputs and can be used to externally PWM the outputs, which is useful when multiple devices need to be dimmed or blinked together without using software control. The PCA9957 also has a short load and overtemperature detection circuitry, thermal shutdown feature which protects the device when the internal junction temperature exceeds the factory-defined limit, and a Reset function routed to the RST pin on the mikroBUS™ which is activated by sending an active low input on this pin with a minimum pulse width of 2.5μs.

The LED Driver 8 Click Board™ is designed to be operated with both 3.3V and 5V logic voltage levels that can be selected via VCC SEL jumper. This allows for both 3.3V and 5V capable MCUs to use the SPI communication lines properly.

SPECIFICATIONS

Type LED Drivers
Applications Can be used in the purpose of LED Status signalization, in LED displays, LED backlight, keypad backlights for cellular phones, or handheld devices, and many more.
On-board modules The LED Driver 8 Click Board™ is based on the PCA9957, a daisy-chain SPI compatible 4-wire serial bus controlled 24-channel constant current LED driver optimized for dimming and blinking 32 mA RGBA LEDs from NXP Semiconductors.
Key Features Low power consumption, programmable LED drivers channels, gradation control for all channels, low standby current, no glitch on LED outputs on Power-Up, and more.
Interface SPI
Compatibility mikroBUS
Click board size M (42.9 x 25.4 mm)
Input Voltage 3.3V or 5V

 

PINOUT DIAGRAM

This table shows how the pinout on the LED Driver 8 Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes Pin Mikrobus logo.png Pin Notes
  NC 1 AN PWM 16 OE Enable Input
Reset Input RST 2 RST INT 15 NC  
SPI Chip Select CS 3 CS RX 14 NC  
SPI Clock SCK 4 SCK TX 13 NC  
SPI Data OUT SDO 5 MISO SCL 12 NC  
SPI Data IN SDI 6 MOSI SDA 11 NC  
Power Supply 3.3V 7 3.3V 5V 10 5V Power Supply
Ground GND 8 GND GND 9 GND Ground

ONBOARD SETTINGS AND INDICATORS

Label Name Default  Description
LD1 PWR - Power LED Indicator
JP1 VCC SEL left Power Supply Voltage Selection 3V3/5V: Left position 3V3, Right position 5V
J1-J3 - - LED Driver Output Header
J4 - - External Output 3.3V Level Supply Header
J5 - - External Output 5V Level Supply Header

LED DRIVER 8 CLICK ELECTRICAL SPECIFICATIONS

Description Min Typ Max Unit
Supply Voltage -0.5 - 6 V
Maximum Output Current on LED pins - - 40 mA
SPI Clock Frequency - - 10 MHz
Operating Temperature Range -40 - +85 °C

 

Frequently Asked Questions

Have a Question?

Be the first to ask a question about this.

Ask a Question

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)