
Key Features
Overview
The Tag-Connect TC2030-MCP cable programs and debugs PIC, dsPIC and PIC32 targets from a Microchip ICD without a header on the board. Its spring-loaded pins press onto six pads in the TC2030 footprint, so the connector costs nothing in the bill of materials and takes little board space (the No Legs footprint is hardly bigger than a surface-mount resistor).
The legged head clips into four locating holes and stays put hands-free through a long debug session. The No Legs head fits the same pad pattern without the four leg latch holes (three small alignment holes remain) and suits quick production programming. Soft Squeeze tabs are easier on operators' fingers in frequent production use, and the long 297 mm version gives extra reach to the board.
One listing for every TC2030-MCP cable. Pick the head, the squeeze tabs and the length above; the price, SKU and stock follow your choice. All versions connect a Microchip ICD programmer or debugger with an RJ12 socket to the 6-pin TC2030 footprint on your board, with no connector fitted to the PCB.
Which Version?
| SKU | Head | Squeeze tabs | Overall length | Best for |
|---|---|---|---|---|
| TC2030-MCP | Legged | Standard | 228 mm (9 in) | Development and debugging; also production programming |
| TC2030-MCP-10 | Legged | Standard | 297 mm (11.7 in) | As TC2030-MCP, when the board sits further from the ICD |
| TC2030-MCP-SOFT | Legged | Soft | 228 mm (9 in) | Frequent production programming; not for debugging or humid environments |
| TC2030-MCP-NL | No legs | Not applicable (no legs to release) | 225 mm (8.9 in) | Production programming with brief connections, board to board |
| TC2030-MCP-NL-10 | No legs | Not applicable (no legs to release) | 297 mm (11.7 in) | As TC2030-MCP-NL, with a longer reach |
The 297 mm versions use a 10 in (254 mm) cable. That is longer than the 8 in maximum cable length Microchip specifies, so Microchip does not support it, although Tag-Connect says it has not been known to cause problems in general use.
Legged and No Legs cables use the same contact pattern, so a board laid out for the legged footprint takes either cable: legged for development, No Legs on the production line. A No Legs cable can be held in place with a TC2030-CLIP retaining clip or a TC-MOUNT-6 fixture, both offered as add-ons above.
Specifications
| Parameter | Value |
|---|---|
| Target end | TC2030 6-pin Plug-of-Nails with spring-loaded pins |
| Tool end | RJ12 modular plug for Microchip ICD |
| Interface | PIC ICD / ICSP (MCLR/Vpp, Vdd, GND, PGD, PGC) |
| Overall length, RJ12 plug to head tip | Standard: 228 mm (9 in) legged, 225 mm (8.9 in) No Legs. Long: 297 mm (11.7 in) |
| Retention (legged) | Four plastic legs clip into locating holes in the board |
| PCB footprint | Legged: TC2030-MCP-FP. No Legs: TC2030-MCP-NL-FP, which also fits the legged footprint. No component is fitted; list it as DNL in your BOM |
Pinout
| Signal | TC2030 pin | RJ12 pin |
|---|---|---|
| MCLR / Vpp | 1 | 6 |
| Vdd | 2 | 5 |
| GND | 3 | 4 |
| PGD (ICSPDAT) | 4 | 3 |
| PGC (ICSPCLK) | 5 | 2 |
| NC / LVP | 6 | 1 |
Compatible Tools
- Microchip MPLAB ICD 3 and ICD 4: plugs straight in.
- CCS programmers: plugs straight in.
- Microchip PICkit 3 and PICkit 4: need Microchip adapter AC164110 (not included). For PICkit 3, 4 and 5 without an adapter, use a TC2030-PKT cable.
- Microchip MPLAB PM3: needs Microchip adapter AC164111 (not included).
PCB Layout Notes
- Leave the contact pads free of solder paste.
- Keep tracks and vias out of the shaded keep-out area.
- Keep tracks and other signals at least 0.02 in (0.5 mm) from any contact pad.
- Allow finger room on the two squeeze-tab sides of a legged footprint.
Full footprint dimensions for both heads are in Tag-Connect's drawings under Downloads. Which cable fits your programmer? See our Microchip PIC Tag-Connect cables, all 6-pin Tag-Connect cables, or the Tag-Connect cable guide.
Not sure which head or length suits your board or fixture? Ask our engineers.
| Ordering information | |
|---|---|
| Part number (SKU) | TC2030-MCP-10 |
| Manufacturer | Tag-Connect, LLC |
| EAN | 5055383603510 |
| Warranty | 6 months |
| Shipping weight | 0.1 kg |
- 1 ×Tag-Connect TC2030-MCP cable, in the version you select
No adapter, retaining clip or fixture is included. On No Legs versions, the TC2030-CLIP retaining clip and the TC-MOUNT-6 fixture are offered as add-ons.
Questions and Answers
-
Which Tag-Connect Cable Do I Need for a PICkit 4 or PICkit 5?
The TC2030-MCP has an RJ12 plug for Microchip's ICD debuggers. For PIC, dsPIC and PIC32 targets on a PICkit 3, 4 or 5, use the TC2030-PKT, which plugs straight into the PICkit's 0.1 in header with no adapter. On the PICkit's 8-pin header, line up pin 1 of both connectors. A PICkit 3 or 4 can also take the TC2030-MCP through Microchip's AC164110 adapter.
-
Can a No Legs Cable Be Used on a Board Laid Out for the Legged Footprint?
Yes. Both heads use the same contact pattern, so a board with the legged TC2030-MCP-FP footprint takes either cable. The No Legs head ignores the four latch holes, so you can debug with the legged cable and program on the production line with No Legs.
-
Does Microchip Support the 297 mm Long Version?
No. Tag-Connect sells the long versions as 10 in (254 mm) cables, 297 mm (11.7 in) overall. That is longer than the 8 in maximum cable length Microchip specifies, so Microchip does not support them. Tag-Connect says they have not been known to cause problems in general use, but does not recommend them with a PICkit 3. Choose the standard length unless you need the extra reach.
-
What Do I Put on My PCB for the TC2030-MCP?
Place the Tag-Connect footprint: TC2030-MCP-FP for the legged head, or TC2030-MCP-NL-FP for No Legs only. No component is fitted, so list it as DNL in your BOM. Keep the pads free of solder paste and keep tracks and vias out of the keep-out area. Both drawings are under Downloads.
No questions match your search.