Mikroelektronika d.o.o.
CAN Isolator Click Board
CAN Isolator Click Board
Couldn't load pickup availability
The CAN Isolator Click Board™ provides isolated CAN communication. It carries the ADM3053 signal and power isolated CAN transceiver with an integrated isolated DC-to-DC converter.
The CAN Isolator Click Board™ is designed to run on either a 3.3V or 5V power supply. CAN Isolator Click Board™ communicates with the target microcontroller over UART interface.
The CAN Isolator Click Board™ provides isolated CAN communication. It carries the ADM3053 signal and power isolated CAN transceiver with an integrated isolated DC-to-DC converter, from Analog Devices. The click is designed to run on either 3.3V or 5V power supply. The CAN Isolator Click Board™ communicates with the target microcontroller over UART interface.
The CAN Isolator Click Board™ carries a DB 9-pin male connector.
ADM3053 FEATURES
The ADM3053 is an isolated controller area network (CAN) physical layer transceiver with an integrated isolated DC-to-DC converter.
The ADM3053 creates a fully isolated interface between the CAN protocol controller and the physical layer bus. It is capable of running at data rates of up to 1 Mbps.
CONNECTOR FEATURES
This is a standard DB 9-pin male connector.
SPECIFICATIONS
| Type | CAN,Isolators |
| Applications | CAN data buses, Industrial field networks |
| On-board modules | ADM3053 CAN transceiver, DB 9-pin connector |
| Key Features | fully isolated interface between the CAN protocol controller and the physical layer bus. It is capable of running at data rates of up to 1 Mbps |
| Interface | UART |
| Compatibility | mikroBUS |
| Click board size | L (57.15 x 25.4 mm) |
| Input Voltage | 3.3V or 5V |
PINOUT DIAGRAM
This table shows how the pinout of the CAN Isolator Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| NC | 1 | AN | PWM | 16 | NC | ||
| NC | 2 | RST | INT | 15 | NC | ||
| NC | 3 | CS | TX | 14 | RXD | Receiver Output Data | |
| NC | 4 | SCK | RX | 13 | TXD | Driver Input Data | |
| NC | 5 | MISO | SCL | 12 | NC | ||
| NC | 6 | MOSI | SDA | 11 | NC | ||
| Power supply | +3.3V | 7 | 3.3V | 5V | 10 | +5V | Power supply |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
JUMPERS AND SETTINGS
| Designator | Name | Default Position | Default Option | Description |
|---|---|---|---|---|
| JP1 | VIO.SEL. | Left | 3V3 | Power Supply Voltage Selection 3V3/5V, left position 3V3, right position 5V |
| JP2 | SLOPE SEL | Left | HI | Slope select, default high rate, right option the slope is limited |
Software Support
CODE SNIPPET
Example of CAN configuration - PIC32
01 // set required baud rate and sampling rules 02 unsigned int can_config_flags; 03 CAN1SetOperationMode(_CAN_MODE_CONFIG,0xFF); 04 can_config_flags = _CAN_CONFIG_SAMPLE_THRICE & 05 _CAN_CONFIG_PHSEG2_PRG_ON & 06 _CAN_CONFIG_STD_MSG & 07 _CAN_CONFIG_MATCH_MSG_TYPE & 08 _CAN_CONFIG_LINE_FILTER_OFF; 09 CAN1SetBaudRate(1,3,3,3,1,can_config_flags); 10 CAN1ConfigureFIFO(_CAN_BUFFER_0, 8,_CAN_FIFO_RX & _CAN_FULL_MESSAGE); 11 CAN1ConfigureFIFO(_CAN_BUFFER_1, 8,_CAN_FIFO_TX & _CAN_TX_PRIORITY_3 & _CAN_TX_NO_RTR_FRAME); 12 CAN1SetMask(_CAN_MASK_0, -1, _CAN_CONFIG_MATCH_MSG_TYPE & _CAN_CONFIG_XTD_MSG); 13 CAN1SetFilter(_CAN_FILTER_31, ID_1st, _CAN_MASK_3, _CAN_BUFFER_0, _CAN_CONFIG_XTD_MSG); 14 CAN1FilterEnable(0x1111);
CAN Isolator Click Board
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.