
Overview
The (Q)SPI Flash Evaluator is an evaluation board for SPI and QSPI flash, used to test SEGGER's emFile NOR and NAND drivers and the direct and indirect programming of serial flash with J-Link probes and Flasher programmers. Flash devices are soldered to plug-in adapter boards for SO-8, SO-8W, SO-16, BGA and SON/DFN packages. A QSPI adapter populated with an ISSI flash device ships in the box.
The SEGGER (Q)SPI Flash Evaluator (part number 6.40.00) is an evaluation board for SPI and QSPI flash, used to test SEGGER's emFile NOR and NAND drivers and the direct and indirect programming of serial flash with J-Link debug probes and Flasher production programmers. Flash devices are soldered to plug-in adapter boards for SO-8, SO-8W, SO-16, BGA and SON/DFN packages, which connect to the carrier through an 8x2 adapter header, and a jumper sets 1.8V or 3.3V flash operation. A QSPI adapter already populated with an ISSI flash device ships in the box, so testing can start before any soldering.
Compare Serial Flash Parts on Interchangeable Adapter Boards
SEGGER built the evaluator to check speed and reliability on the actual flash part. Each candidate device is soldered to the adapter board that matches its package, then plugged into the carrier through the 8x2 adapter header; swapping parts means swapping adapters, not reworking the main board. SEGGER publishes schematics for the SO and SON/DFN adapters.
Direct SPI Flash Programming with J-Link and Flasher
In direct programming the J-Link or Flasher connects straight to the flash SPI interface, with no CPU in between; in indirect programming it connects to the microcontroller, which then programs the flash. SEGGER's Knowledge Base sets out the direct programming procedure: set the SEL 1.8V jumper (closed for 1.8V flash, open for 3.3V flash), plug in the flash adapter with pin 1 aligned, power the evaluator over micro-USB until the PWR LED lights, connect the J-Link or Flasher with a 20-pin ribbon cable and start J-Flash SPI. QSPI evaluation needs board revision A or later, marked Rev. A on the back of the board.
emFile and emPower OS Evaluation Software
The evaluator comes with a preconfigured emPower OS evaluation package for SEGGER Embedded Studio, licensed under the SEGGER Friendly License (SFL) for evaluation and non-commercial use with full functionality. The emFile components listed are BASE with Encryption, FAT, FAT LFN, Journaling, NAND and RAMDisk. The package also includes embOS, emUSB-Device, emNet, emSSL, emSSH, emSecure, emCrypt, emCompress, emModbus, emWeb and the IoT Toolkit.
Specifications
| Part number | 6.40.00 |
|---|---|
| Flash types | SPI and QSPI flash, NOR and NAND |
| Adapter connection | 8x2 adapter header |
| Adapter packages | SO-8, SO-8W, SO-16; BGA 4x6mm and 5x5mm; SON/DFN 8x6, 6x5, 4x4, 3x4, 3x2 |
| Flash voltage | 1.8V or 3.3V, set by the SEL 1.8V jumper |
| Power | Micro-USB |
| Programmer connection | J-Link or Flasher via 20-pin ribbon cable |
| Programming modes | Direct (programmer to SPI interface) and indirect (programmer to microcontroller) |
| Host software | J-Link software package; J-Flash SPI for direct programming |
| Host OS | Windows, Linux, macOS |
| QSPI support | Board revision A or later |
| emFile components | BASE with Encryption, FAT, FAT LFN, Journaling, NAND, RAMDisk |
| Evaluation licence | SEGGER Friendly License (SFL), evaluation and non-commercial use |
What's Included
- (Q)SPI Flash Evaluator carrier board
- QSPI adapter populated with ISSI IS25LPO64D flash chip (as SEGGER lists it)
- 3 adapter boards for SO-8, SO-8W, SO-16 (blank PCB)
- 3 adapter boards for BGA 4x6mm and 5x5mm (blank PCB)
- 3 adapter boards for SON/DFN 8x6, 6x5, 4x4, 3x4, 3x2 (blank PCB)
- 6 connectors
- Micro USB cable
Limitations
- No J-Link or Flasher is included, and SEGGER's package list names no 20-pin ribbon cable; use the cable supplied with your probe.
- J-Flash SPI is not included with J-Link BASE. It comes with the J-Link PLUS, or with the BASE to PLUS upgrade licence for an existing BASE.
- The supplied adapter boards are blank: soldering your own flash devices to them is required.
- QSPI evaluation needs board revision A or later.
- The bundled software is licensed for evaluation and non-commercial use only.
SEGGER Flash Evaluators Compared
| Model | Flash type | Device mounting | Programming and debug | Price ex VAT |
|---|---|---|---|---|
| (Q)SPI Flash Evaluator (this product) | SPI and QSPI NOR and NAND | Devices soldered to SO, BGA or SON/DFN adapter boards | J-Link or Flasher, direct or indirect programming | £248 |
| NAND Flash Evaluator | Parallel NAND, 8-bit or 16-bit bus | TSOP48 socket; VFBGA63 adapter as add-on | J-Link, 19-pin debug header | £270 |
| J-Link PLUS Compact | Debug probe with J-Flash SPI included, for direct programming | £660 | ||
| J-Link BASE Compact | Debug probe; J-Flash SPI not included | £470 | ||
Typical Applications
Shortlisting QSPI NOR parts in SO-8W or SON packages for a new design by soldering each to an adapter and testing it on the same carrier. Proving direct SPI flash programming with J-Flash SPI and a Flasher before setting up a production programming station. Running emFile journaling on a serial NAND device to check its behaviour before choosing it for a data logging product.
The board suits firmware engineers selecting serial flash and production engineers planning in-system flash programming.
Order the (Q)SPI Flash Evaluator for £248 ex VAT, or ask us for a formal quotation. See the full range in our SEGGER debug probes collection.
Last reviewed 16/11/2026.
| General | |
|---|---|
| Part number | 6.40.00 |
| Flash types | SPI and QSPI flash, NOR and NAND |
| Adapter connection | 8x2 adapter header |
| Adapter packages | SO-8, SO-8W, SO-16; BGA 4x6mm and 5x5mm; SON/DFN 8x6, 6x5, 4x4, 3x4, 3x2 |
| Flash voltage | 1.8V or 3.3V, set by the SEL 1.8V jumper |
| Programmer connection | J-Link or Flasher via 20-pin ribbon cable |
| Programming modes | Direct (programmer to SPI interface) and indirect (programmer to microcontroller) |
| QSPI support | Board revision A or later |
| emFile components | BASE with Encryption, FAT, FAT LFN, Journaling, NAND, RAMDisk |
| Power | |
| Power | Micro-USB |
| Software and Compatibility | |
| Host software | J-Link software package; J-Flash SPI for direct programming |
| Host OS | Windows, Linux, macOS |
| Evaluation licence | SEGGER Friendly License (SFL), evaluation and non-commercial use |
| Ordering information | |
| Part number (SKU) | 6.40.00 |
| Manufacturer | SEGGER Microcontroller GmbH |
| EAN | 5055383699162 |
| Warranty | 12 Monate |
| Shipping weight | 0.02 kg |
- 1 ×(Q)SPI Flash Evaluator carrier board
- 1 ×QSPI adapter populated with ISSI IS25LPO64D flash chip
- 3 ×Adapter boards for SO-8, SO-8W, SO-16 (blank PCB)
- 3 ×Adapter boards for BGA 4x6mm and 5x5mm (blank PCB)
- 3 ×Adapter boards for SON/DFN 8x6, 6x5, 4x4, 3x4, 3x2 (blank PCB)
- 6 ×Connectors
- 1 ×Micro USB cable
Questions and Answers
-
Can I Program the Flash Directly with a J-Link?
Yes. Connect the J-Link or Flasher to the evaluator with a 20-pin ribbon cable and use J-Flash SPI, which drives the flash SPI interface with no CPU in between. J-Flash SPI is not part of J-Link BASE; it comes with J-Link PLUS or the BASE to PLUS upgrade.
-
Does the Evaluator Support 1.8V Flash?
Yes. Close the SEL 1.8V jumper for 1.8V flash and leave it open for 3.3V flash.
-
Can I Test My Own Flash Device?
Yes. Solder it to the blank adapter board that matches its package (SO-8, SO-8W, SO-16, BGA or SON/DFN) and plug the adapter into the 8x2 adapter header.
No questions match your search.