
Key Features
Overview
The SEGGER USB Isolator (8.07.02) fits between the host PC and a J-Link or Flasher and isolates the probe from the PC, with 3kV DC basic isolation (for 1s). The link runs at USB Full-Speed and the isolator supplies the probe with up to 200mA. Use it when the PC and the target application are not on the same ground, or to protect the probe from spikes and overvoltage from low-budget USB hubs.
The SEGGER USB Isolator (part number 8.07.02) sits in the USB link between the host PC and a J-Link or Flasher, giving 3kV DC basic isolation (for 1s) between the probe and the host. It runs the connection at USB Full-Speed (12 Mbit/s) with a maximum propagation delay of 70ns, and supplies the probe with up to 200mA. It suits setups where the PC and the target application are not on the same ground, and it protects the probe from electrical spikes and from the overvoltage that low-budget USB hubs can cause.
Host-Side Isolation Without Slowing the Debug Link
Isolating on the host side forces the PC to talk to the probe at USB Full-Speed. SEGGER states that this does not, or not significantly, reduce debug and flash programming speed. The 70ns propagation delay is treated as one additional USB hub. Host-side isolation works with every debug interface the probe supports, including JTAG, SWD (with or without SWO), FINE, C2 and UART, and it isolates both the probe and the target from the PC. Where USB Hi-Speed (480 Mbit/s) is needed, isolate on the target side instead with the JTAG or SWD Isolator, which typically limits the target-side debug speed.
Connectors, Indicators and Protection
A USB Micro-B connector faces the PC and a USB Type-A connector faces the J-Link or Flasher. A green PWR LED shows the isolator is powered and can supply the probe side; a red/orange OVL LED shows overload when the probe draws too much current. The isolator has short-circuit protection.
What's Included
SEGGER publishes no package list for the USB Isolator. You receive the isolator itself. SEGGER does not say whether a USB Micro-B cable for the host side is supplied, so ask us before ordering if you need one.
Specifications
| Isolation | 3kV DC for 1s, basic isolation |
|---|---|
| USB speed | USB Full-Speed, 12 Mbit/s |
| Propagation delay | 70ns max. (counts as one additional hub) |
| Max. output current to probe | 200mA |
| Host-side connector | USB Micro-B |
| Probe-side connector | USB Type-A |
| Indicators | PWR (green), OVL overload (red/orange) |
| Protection | Short-circuit protection |
| Compatible J-Link models | PRO, Ultra, WiFi, PLUS Classic and Compact, BASE Classic and Compact |
| Compatible Flasher models | PRO, PRO XL, Compact, Portable PLUS |
Limitations
- The host link runs at USB Full-Speed only. For Hi-Speed USB, isolate on the target side with the JTAG or SWD Isolator.
- The connected probe may draw no more than 200mA.
- On a J-Link PRO V4 or J-Link ULTRA+ V4, apply firmware updates with the isolator removed. SEGGER reports that these two models can lose communication during a firmware update made through the USB Isolator; refit it once the update has finished.
- Basic isolation only. Do not use it with hazardous voltages without a further protection measure such as double or reinforced isolation.
- SEGGER does not support other vendors' USB isolators with J-Link; their use is at your own risk.
USB Isolator Compared with Other SEGGER Isolators
| Isolator | Isolated link | Isolation | Max. speed | Price ex VAT |
|---|---|---|---|---|
| USB Isolator (this product) | Host PC to probe, USB | 3kV DC for 1s, basic | USB Full-Speed, 12 Mbit/s | £185 |
| JTAG Isolator | Probe to target, JTAG, 20-pin 0.1" | 1kV DC, basic | 4 MHz | £226 |
| SWD Isolator | Probe to target, SWD and SWO, 20-pin 0.1" | 1kV DC, basic | 4 MHz | £240 |
| J-Trace Isolator | J-Trace to target, JTAG, SWD, SWO and ETM trace, 19-pin 0.05" | 1kV DC, basic | 4 MHz debug, 75 MHz trace clock | £320 |
Order the USB Isolator for £185 ex VAT. Check that your probe is among the compatible models in the specifications above, such as the J-Link BASE Classic, J-Link PLUS Classic or Flasher PRO, or ask us for a formal quotation. See the full range in our SEGGER debug probes collection.
Last reviewed 16/11/2026.
| General | |
|---|---|
| Isolation | 3kV DC for 1s, basic isolation |
| Propagation delay | 70ns max. (counts as one additional hub) |
| Max. output current to probe | 200mA |
| Indicators | PWR (green), OVL overload (red/orange) |
| Protection | Short-circuit protection |
| Host and Target Interface | |
| Host-side connector | USB Micro-B |
| Probe-side connector | USB Type-A |
| Performance | |
| USB speed | USB Full-Speed, 12 Mbit/s |
| Software and Compatibility | |
| Compatible J-Link models | PRO, Ultra, WiFi, PLUS Classic and Compact, BASE Classic and Compact |
| Compatible Flasher models | PRO, PRO XL, Compact, Portable PLUS |
| Ordering information | |
| Part number (SKU) | 8.07.02 |
| Manufacturer | SEGGER Microcontroller GmbH |
| EAN | 5055383619979 |
| Warranty | 12 Monate |
| Shipping weight | 0.05 kg |
-
1 ×
SEGGER USB-Isolationsadapter
Contact us to confirm the full contents of the box.
Questions and Answers
-
Will the USB Isolator Slow Down Debugging?
Not significantly, according to SEGGER. The host link runs at USB Full-Speed (12 Mbit/s), which SEGGER describes as typically fully sufficient for debugging and flash programming.
-
Which Isolator Keeps USB Hi-Speed?
The target-side isolators. The JTAG Isolator and SWD Isolator allow the USB link to run at Hi-Speed (480 Mbit/s) on J-Link models that support it, but typically limit the target-side debug speed, to 4 MHz on both.
-
Does the USB Isolator Work with SWD, JTAG and Other Debug Interfaces?
Yes. SEGGER states that host-side isolation works with all the debug interfaces the probe supports, including JTAG, SWD (with or without SWO), FINE, C2 and UART. The isolator sits in the USB link and leaves the target connection unchanged.
No questions match your search.