Mikroelektronika d.o.o.
Druck 9 Click Board
Druck 9 Click Board
Verfügbarkeit für Abholungen konnte nicht geladen werden
Overview
Das Pressure 9 Click Board™ ist ein digitaler barometrischer Luftdrucksensor Click Board™. Es ist mit dem barometrischen Luftdrucksensor DPS422 ausgestattet, der auf einem kapazitiven Sensorelement basiert. Neben dem Druck kann dieser Sensor auch die Temperatur messen. Messdaten sind über die I2C- oder SPI-Schnittstelle verfügbar, zusammen mit den werkseitig kalibrierten Koeffizienten, die für eine hochgenaue Datenkonvertierung verwendet werden. Das Gerät verfügt außerdem über einen 32 Wörter langen FIFO-Puffer, einen geringen Stromverbrauch und eine sehr hohe Präzision dank eines integrierten 24-Bit-A/D-Wandlers.
Das Pressure 9 Click Board™ kann in einem Druckbereich von 300 bis 1200 hPa und einem Temperaturbereich von -40⁰C bis +85⁰C eingesetzt werden.
The DPS422 is designed with the low-power consumption in mind, has a very small size, and requires a low number of external components. These features make the DPS422 a perfect choice for an IoT or battery-powered application. Therefore, Pressure 9 click can be used as a tool for development of various pressure-based IoT applications, as well as other applications where the power consumption and constrained space could be a problem: portable weather stations, room temperature control, applications related to elevation gain and vertical speed detection, sports-related wearables, and similar.
How Does The Pressure 9 Click Board™ Work?
The Pressure 9 Click Board™ features the DPS422, a digital barometric air pressure sensor, by Infineon. It can be used to measure absolute pressure values from 300 to 1200hPa. The sensor contains a highly accurate capacity-based Micro Electro-Mechanical Sensor (MEMS), along with a high resolution 24-bit sigma-delta A/D converter (ADC). The MEMS also features a set of factory calibration parameters, stored into its OTP memory. They allow high-precision pressure and temperature data conversions to be performed, enabling results in physical units. By adjusting the oversampling ratio, the developer can find a perfect balance between the accuracy, speed (output data rate), and power consumption, in accordance to the application requirements.
MEMS consists a set of tubular vacuum cells, covered by membranes. By applying a pressure, capacitance of the cell is changed proportionally. Several vacuum cells are connected in parallel, allowing for better sensitivity and less noise. The capacitance of the cells is measured and converted to a voltage which is sampled by the internal 24-bit ADC. The result is available over I2C or SPI interface, depending on the position of the COMM SEL jumpers. The conversion formula is then applied to the raw result value, providing pressure and temperature values in human readable format.
The Pressure 9 Click Board™ supports both SPI and I2C communication interfaces, allowing it to be used with a wide range of different MCUs. The communication interface can be chosen by moving SMD jumpers grouped under the COM SEL to an appropriate position (SPI or I2C). The slave I2C address can also be configured by a SMD jumper, when operated in the I2C mode: a SMD jumper labeled as ADD SEL is used to set the least significant bit (LSB) of the I2C address. When set to 0, the 7-bit I2C slave address becomes 0b1110110x. If set to 1, the address becomes 0b1110111x. The last digit (x) is the R/W bit. Please note that each jumper should be moved to the same position, else the communication with the host MCU may not be possible.
One of distinctive features of the DPS422 is the FIFO buffer with 32 slots, allowing to buffer both pressure and temperature readings. The FIFO buffer can be used as a temporary storage for the incoming data, allowing for reduced data traffic through the communication bus. The FIFO buffer can be very useful for writing an optimized MCU firmware. The least significant bit (LSB) of the result stored within the FIFO buffer, determines if the stored data represents pressure, or temperature (1 is used for pressure, 0 for temperature). A bit within the FIFO status register indicates if the buffer is full or if the watermark level has been reached. The FIFO buffer can also be disabled, allowing data to be fetched from the output registers, directly.
Pressure and thermal data are available at the output, in 24-bit, two's complement format. To convert the raw data into a human-readable format, the firmware of the host MCU has to obtain the calibration data. Calibration coefficients are then used within pressure or temperature conversion formulas. The required formulas can be found within the datasheet of the DPS422. However, the Pressure 9 Click Board™ comes with the mikroSDK compatible library of functions that simplify the firmware development. The developer is able to use simple function calls, which perform all the necessary data conversion, returning the pressure and thermal data in human readable format.
The Pressure 9 Click Board™ is designed to be operated by 3.3V logic levels only. A proper logic voltage level translation should be performed before the Click board™ is used MCUs which are operated at 5V.
SPECIFICATIONS
| Type | Pressure |
| Applications | A perfect tool for development of various pressure-based IoT applications, as well as other low-power and space-constrained applications: portable weather stations, room temperature control, applications related to elevation gain and vertical speed detection, sports-related wearables, and similar. |
| On-board modules | DPS422, a digital barometric air pressure sensor, by Infineon. |
| Key Features | 24-bit conversion, high precision, low power consumption, low count of external components required, both pressure and temperature data, factory programmed calibration parameters, perfect for IoT based applications. |
| Interface | I2C,SPI |
| Compatibility | mikroBUS |
| Click board size | M (42.9 x 25.4 mm) |
| Input Voltage | 3.3V |
PINOUT DIAGRAM
This table shows how the pinout on the Pressure 9 Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| NC | 1 | AN | PWM | 16 | NC | ||
| NC | 2 | RST | INT | 15 | NC | ||
| Control IN 2 | CS | 3 | CS | RX | 14 | NC | |
| SPI Clock | SCK | 4 | SCK | TX | 13 | NC | |
| SPI Data OUT | SDO | 5 | MISO | SCL | 12 | SCL | I2C Clock |
| SPI Data IN | SDI | 6 | MOSI | SDA | 11 | SDA | I2C Data |
| Power Supply | 3.3V | 7 | 3.3V | 5V | 10 | NC | |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
PRESSURE 9 CLICK ELECTRICAL SPECIFICATIONS
| Description | Min | Typ | Max | Unit |
|---|---|---|---|---|
| Pressure range | 300 | 1200 | hPa | |
| Temperature range | -40 | +85 | ˚C |
ONBOARD SETTINGS AND INDICATORS
| Label | Name | Default | Description |
|---|---|---|---|
| LD1 | PWR | - | Power LED Indicator |
| JP1, JP3 | COM SEL | Left | Communication interface selection: left position I2C, right position SPI |
| JP4 | ADDR SEL | Left | Slave I2C address LSB selection: left position 0, right position 1 |
Software Support
We provide a library for the Pressure 9 Click Board™ on our LibStock page, as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Library Description
The library initializes and defines the I2C or SPI bus driver and drivers that offer a choice for writing data in register and reads data form register. The library includes function for read Pressure data in mBar and Temperature data in C. The user also has the function for update all calibration coefficients, function for configuration register and functions for get Pressure and Temperature raw data.
Key Functions
float pressure9_getTemperatureData()- Temperature data.float pressure9_getPressureData()- Pressure data.void pressure9_updateCalculationCoefficient()- Update all calibration coefficients.
Example Description
The application is composed of the three sections :
- System Initialization - Initializes I2C or SPI module and sets CS pin as OUTPUT for select comunication.
- Application Initialization - Initialization driver init, test comunication, software reset, configuration module for measurement and calls the function to update calibration coefficients - this function must be called before the measurement starts.
- Application Task - Reads Temperature data in [C] and Pressure data in [mBar] and this data logs to the USBUART every 1 sec.
void applicationTask()
{
float Temperature;
float Pressure;
char demoText[ 50 ] = {0};
Pressure = pressure9_getPressureData();
FloatToStr(Pressure, demoText);
mikrobus_logWrite(" -- Pressure : ", _LOG_TEXT);
mikrobus_logWrite(demoText, _LOG_LINE);
Temperature = pressure9_getTemperatureData();
FloatToStr(Temperature, demoText);
mikrobus_logWrite(" -- Temperature : ", _LOG_TEXT);
mikrobus_logWrite(demoText, _LOG_LINE);
mikrobus_logWrite("-----------------------------", _LOG_LINE);
Delay_ms( 500 );
}
The full application code, and ready to use projects can be found on our LibStock page.
Other mikroE Libraries used in the example:
I2CSPIUARTConversions
Additional Notes and Information
Depending on the development board you are using, you may need a USB UART click, USB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.
MIKROSDK
The Pressure 9 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant click board demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Software Support
We provide a library for the Pressure 9 Click Board™ on our LibStock page, as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Library Description
The library initializes and defines the I2C or SPI bus driver and drivers that offer a choice for writing data in register and reads data form register. The library includes function for read Pressure data in mBar and Temperature data in C. The user also has the function for update all calibration coefficients, function for configuration register and functions for get Pressure and Temperature raw data.
Key Functions
float pressure9_getTemperatureData()- Temperature data.float pressure9_getPressureData()- Pressure data.void pressure9_updateCalculationCoefficient()- Update all calibration coefficients.
Example Description
The application is composed of the three sections :
- System Initialization - Initializes I2C or SPI module and sets CS pin as OUTPUT for select comunication.
- Application Initialization - Initialization driver init, test comunication, software reset, configuration module for measurement and calls the function to update calibration coefficients - this function must be called before the measurement starts.
- Application Task - Reads Temperature data in [C] and Pressure data in [mBar] and this data logs to the USBUART every 1 sec.
void applicationTask()
{
float Temperature;
float Pressure;
char demoText[ 50 ] = {0};
Pressure = pressure9_getPressureData();
FloatToStr(Pressure, demoText);
mikrobus_logWrite(" -- Pressure : ", _LOG_TEXT);
mikrobus_logWrite(demoText, _LOG_LINE);
Temperature = pressure9_getTemperatureData();
FloatToStr(Temperature, demoText);
mikrobus_logWrite(" -- Temperature : ", _LOG_TEXT);
mikrobus_logWrite(demoText, _LOG_LINE);
mikrobus_logWrite("-----------------------------", _LOG_LINE);
Delay_ms( 500 );
}
The full application code, and ready to use projects can be found on our LibStock page.
Other mikroE Libraries used in the example:
I2CSPIUARTConversions
Additional Notes and Information
Depending on the development board you are using, you may need a USB UART click, USB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.
MIKROSDK
The Pressure 9 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant click board demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.