Mikroelektronika d.o.o.
Thermostat 4 Click-Platine
Thermostat 4 Click-Platine
Verfügbarkeit für Abholungen konnte nicht geladen werden
Das Thermostat 4 Click Board ™ ist eine Komplettlösung, die die Temperatur eines physischen Systems erfasst und Aktionen ausführen kann, sodass die Temperatur des Systems in der Nähe eines gewünschten Sollwerts gehalten wird. Es basiert auf Texas Instruments TMP392, einem widerstandsprogrammierbaren Temperaturschalter, der Schutz und Erkennung thermischer Systemereignisse von 30 °C bis 130 °C ermöglicht. Es bietet eine duale Übertemperaturerkennung (heiß und warm). Die Auslösetemperaturoption wird programmiert, indem der Trimmerwiderstandswert für Kanal A und der digitale Potentiometerwiderstandswert über die SPI-Schnittstelle für Kanal B geändert werden. Das Thermostat 4 Click enthält außerdem ein hochwertiges Relais von Omron, mit dem ein Stromkreis geöffnet oder geschlossen werden kann. Trotz seiner geringen Größe kann es mit Spannungen bis zu 30 VDC/220 AC und Stromstärken bis zu 5 A verwendet werden.
Das Thermostat 4 Click Board™ wird von einer mikroSDK-kompatiblen Bibliothek unterstützt, die Funktionen enthält, die die Softwareentwicklung vereinfachen. Dieses Click Board™ wird als vollständig getestetes Produkt geliefert und ist bereit für den Einsatz auf einem System, das mit der mikroBUS™-Buchse ausgestattet ist.
How Does The Thermostat 4 Click Board™ Work?
The Thermostat 4 Click Board™ uses the output of the TMP392 as open-drain and with two 10k pull-up resistors on mikroBUS™ OA and OB pins connected to VCC voltage indicate when a threshold temperature is detected. The device powers on when the supply voltage goes beyond 1.5V, and starts sampling the input resistance to set the two trip points and hysteresis value after power-on. Resistance values for each temperature can be find in TMP392 datasheet Table 1 and Table 2. These values will remain the same until the device goes through a power cycle.
.jpg)
Trip point for channel A can be set manually using onboard trimmer while trip point for channel B is set using TPL0501 digital potentiometer with 256 wiper positions used as as a two-terminal rheostat. With end-to-end resistance of 100 kΩ internal registers of the TPL0501 can be accessed using a SPI interface. The position of the wiper (W) terminal is controlled by the value in the 8-bit Wiper Resistance (WR) register. When the WR register contains all zeroes (zero-scale), the wiper terminal is closest to its L terminal. As the value of the WR register increases from all zeroes to all ones (full-scale), the wiper moves from the position closest to the L terminal, to the position closest to the H terminal. At the same time, the resistance between W and L increases, whereas the resistance between W and H decreases.
The relay is activated by the host MCU. The voltage for the coil activation is 5V, while the current through the coil is 40mA. The MCU is not able to drive the coil directly, therefore an N-chanel FET had to be added. Its gate is controlled by the host MCU, allowing the coil to drain enough current from the 5V mikroBUS™ power rail. A red color LED, labelled as ACTIVE is used to indicate that the transistor is in an open state and that the current is running through the relay coil.
When the current through a coil (or any other inductor) is suddenly changed, the backEMF will be generated, opposing the changes of the current. This can sometimes lead to damage to the control circuit: in this case, the transistor will become inversely polarized. To prevent this from happening, a flyback diode is added across the coil. During the normal operation, this diode does not conduct any current. However, when the coil is switched OFF, the inverse polarization will cause the current to pass through this diode with minimum resistance. This prevents inverse (flyback) voltage from building up, so the transistor remains safe.
The Thermostat 4 Click Board™ is equipped with all the necessary elements, required to provide a reliable operation: it has a varistor across the relay output contacts, preventing excessive voltage transients, it has a flyback diode for the backEMF generated within the relay coil, and a durable mechanical relay, that can withstand up to 20,000,000 mechanical cycles (no load connected). These features allow Thermostat 4 Click Board™ to be used for a wide range of applications that have to be thermally controlled: various home appliances, air conditioners, cooling fans, small heaters, etc.
SPECIFICATIONS
| Type | Temperature & humidity |
| Applications | The Thermostat 4 Click Board™ can be used for a wide range of applications that have to be thermally controlled: various home appliances, air conditioners, cooling fans, small heaters, etc |
| On-board modules | TMP392 |
| Key Features | Dual outputs for overtemperature detection, Trip test function enables in-system testing, Resistor tolerances contribute zero error |
| Interface | GPIO,SPI |
| Compatibility | mikroBUS |
| Click board size | M (42.9 x 25.4 mm) |
| Input Voltage | 3.3V or 5V |
PINOUT DIAGRAM
This table shows how the pinout of the Thermostat 4 Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| Channel A Output | OA | 1 | AN | PWM | 16 | RLY | Relay Control |
| Reset | RST | 2 | RST | INT | 15 | OB | Channel B Output |
| SPI Chip Select | CS | 3 | CS | RX | 14 | NC | |
| SPI Clock | SCK | 4 | SCK | TX | 13 | NC | |
| NC | 5 | MISO | SCL | 12 | NC | ||
| SPI Data IN | SDI | 6 | MOSI | SDA | 11 | NC | |
| Power Supply | 3.3V | 7 | 3.3V | 5V | 10 | 5V | Power Supply |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
ONBOARD SETTINGS AND INDICATORS
| Label | Name | Default | Description |
|---|---|---|---|
| PWR | LD1 | - | Power LED Indicator |
| ACTIVE | LD2 | - | Relay active LED indicator |
| VCC SEL | JP1 | Left | Logic level voltage selection: left position 3V3, right position 5V |
Software Support
We provide a library for the Thermostat 4 Click Board™ on our LibStock page, as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Library Description
The library contains basic functions for working with the Thermostat 4 Click Board™.
Key Functions
void thermostat4_relay_ctrl( uint8_t state )- Relay Controluint8_t thermostat4_hot_alert_state( void )- Hot temperature ALERTuint8_t thermostat4_warm_alert_state( void )- Warm temperature ALERT
Example Description
The application is composed of three sections :
- System Initialization - Initializes SPI module and all necessary GPIO pins
- Application Initialization - Initializes Driver init, Relay test and sets hysteresis on the WARM channel ( channel B ), after thet starts uploading new data.
- Application Task - Reads Alert on the WARM and HOT channel.
- note: The user has the option of adjusting the hysteresis for channel B via the SPI module while for channel A it is adjusted via the potentiometer.
void application_task ( ) { if ( thermostat4_hot_alert_state( ) == THERMOSTAT4_HOT_ALERT ) { mikrobus_logWrite( ">> H-O-T A-L-E-R-T <<", _LOG_LINE ); thermostat4_relay_ctrl( THERMOSTAT4_RELAY_ON ); } if ( thermostat4_warm_alert_state( ) == THERMOSTAT4_WARM_ALERT ) { mikrobus_logWrite( ">> W-A-R-M A-L-E-R-T <<", _LOG_LINE ); thermostat4_relay_ctrl( THERMOSTAT4_RELAY_ON ); } mikrobus_logWrite( ">> T-E-M-P-E-R-A-T-U-R-E O-K <<", _LOG_LINE ); thermostat4_relay_ctrl( THERMOSTAT4_RELAY_OFF ); Delay_ms( 200 ); }
The full application code, and ready to use projects can be found on our LibStock page.
Other mikroE Libraries used in the example:
- SPI Library
- UART Library
Additional Notes and Information
Depending on the development board you are using, you may need USB UART Click Board™, USB UART 2 Click Board™ or RS232 Click Board™ to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.
MIKROSDK
The Thermostat 4 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Software Support
We provide a library for the Thermostat 4 Click Board™ on our LibStock page, as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Library Description
The library contains basic functions for working with the Thermostat 4 Click Board™.
Key Functions
void thermostat4_relay_ctrl( uint8_t state )- Relay Controluint8_t thermostat4_hot_alert_state( void )- Hot temperature ALERTuint8_t thermostat4_warm_alert_state( void )- Warm temperature ALERT
Example Description
The application is composed of three sections :
- System Initialization - Initializes SPI module and all necessary GPIO pins
- Application Initialization - Initializes Driver init, Relay test and sets hysteresis on the WARM channel ( channel B ), after thet starts uploading new data.
- Application Task - Reads Alert on the WARM and HOT channel.
- note: The user has the option of adjusting the hysteresis for channel B via the SPI module while for channel A it is adjusted via the potentiometer.
void application_task ( ) { if ( thermostat4_hot_alert_state( ) == THERMOSTAT4_HOT_ALERT ) { mikrobus_logWrite( ">> H-O-T A-L-E-R-T <<", _LOG_LINE ); thermostat4_relay_ctrl( THERMOSTAT4_RELAY_ON ); } if ( thermostat4_warm_alert_state( ) == THERMOSTAT4_WARM_ALERT ) { mikrobus_logWrite( ">> W-A-R-M A-L-E-R-T <<", _LOG_LINE ); thermostat4_relay_ctrl( THERMOSTAT4_RELAY_ON ); } mikrobus_logWrite( ">> T-E-M-P-E-R-A-T-U-R-E O-K <<", _LOG_LINE ); thermostat4_relay_ctrl( THERMOSTAT4_RELAY_OFF ); Delay_ms( 200 ); }
The full application code, and ready to use projects can be found on our LibStock page.
Other mikroE Libraries used in the example:
- SPI Library
- UART Library
Additional Notes and Information
Depending on the development board you are using, you may need USB UART Click Board™, USB UART 2 Click Board™ or RS232 Click Board™ to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.
MIKROSDK
The Thermostat 4 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Thermostat 4 Click-Platine
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.