Picotest
Carte de démonstration du système distribué Picotest VRTS3 V1.0
Carte de démonstration du système distribué Picotest VRTS3 V1.0
Analyse Distributed Systems with Precision and Ease
SKU: VRTS3
Prix habituel
€370,95 EUR
hors taxes
Prix habituel
Prix promotionnel
Prix unitaire
par
€370,95 EUR
hors taxes
Frais d'expédition calculés à l'étape de paiement.
If no stock shown above, order NOW to ship within 7 working days
Impossible de charger la disponibilité du service de retrait
Key Features
- Multiple Channel Support: Analyse multiple signals simultaneously for comprehensive system evaluation.
- Multiple Channel Support: Analyse multiple signals simultaneously for comprehensive system evaluation.
- User-Friendly Interface: Intuitive controls for easy setup and operation.
- Comprehensive User Manual: Detailed guidance for installation, operation, and troubleshooting.
- Signal Integrity Analysis: Evaluate signal quality and timing relationships with precision.
- Power Distribution Insight: Understand power distribution dynamics within your circuits.
- Compact Design: Integrates effortlessly into your existing test setup.
Overview
La carte de démonstration Picotest VRTS3 est une carte autonome conçue pour prendre en charge une large gamme de mesures de systèmes distribués classiques. L'alimentation d'entrée est fournie via un port USB à l'aide d'un câble USB-A vers USB-B classique. Aucun équipement supplémentaire n'est requis pour cette carte autre que les instruments de mesure.The Picotest VTS3 Demo Board contains eight individual circuit sections as identified in the table below. These circuits are typical in most distributed systems providing an excellent test bed for demonstrating non-invasive, in-system measurement, optimization and troubleshooting techniques.
VRTS3 Board Sections
| Section | Function |
| POL | 5V USB input to 3.3V 2.8MHz switching regulator |
| REF03 | 2.5V low noise voltage reference |
| OPAMP | 245MHz Bandwidth unity gain opamp buffer |
| LDO | LD1086 voltage regulator 5V USB input to 3.3V output |
| CLOCKS/BUFFERS | 10MHz and 125MHz clocks |
| CALIBRATION | Short-Open-Load and 1 Ohm calibration ports |
| PLANES & CAPS | Parallel tantalum and ceramic capacitor on a small PCB plane |
| MICROSTRIPS | 50O microstrips with precision aberrations - one with a ground void |
Supported Measurements
|
TEST |
SIGNAL INJECTORS NEEDED |
| 1 Port Impedance | DC Block |
| Output Impedance | See Impedance Table 2 |
| Bode Plot | J2100A or J2101A |
| Non-invasive Stability | See Impedance Table 2 |
| Switching Frequency | |
| Switch Rise Time | |
| Duty Cycle Jitter | |
| Noise | DC Block, 1 Port Probe, Preamp |
| PSRR | DC Block, J2120A, or J2111A |
| Step Load Response | J2111A or J2112A |
| Clock Jitter | |
| Clock Rise Time | |
| Jitter Sensitivity | DC Block |
| Power Supply Impedance | See Impedance Table 2 |
| Crosstalk | |
| Clock Buffer PDN Noise | DC Block |
| Clock Buffer Impedance | See Impedance Table 2 |
| Parallel Capacitor resonance | 1 Port Probe |
| Plane Impedance | 1 Port Probe |
| Velocity Factor and Er | |
| Trace Impedance | |
| Impedance of Broken Ground | |
| 2 port Shunt Thru Impedance | J2120A, 2 Port Probe, DC Block |
| Ripple | DC Block, Preamp |
| EMI | Near Field Probes |
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.