Mikroelektronika d.o.o.
Planche à 4 clics Balancer
Planche à 4 clics Balancer
Impossible de charger la disponibilité du service de retrait
Key Features:
- Batteries lithium-ion à deux cellules en série, courant de charge configurable jusqu'à 2 A, compatibles avec le contrôle hôte ou le mode autonome, gestion du chemin d'alimentation NVDC, circuit d'équilibrage de cellules intégré pour les cellules dépareillées, indicateurs d'état, interface I2C, NTC, et plus encore
- Basé sur le MP2672A - chargeur de batterie à découpage hautement intégré et flexible de Monolithic Power Systems (MPS)
- Peut être utilisé pour des applications portables, des machines de point de vente (POS), des applications générales à deux cellules, etc.
- mikroBUS : interface I2C
Le Balancer 4 Click Board™ est une carte complémentaire compacte optimisée pour la protection contre les surtensions qui équilibre la tension des batteries connectées en série. Cette carte comprend le MP2672A, un chargeur de batterie à découpage flexible et hautement intégré pour les batteries lithium-ion avec deux cellules en série de Monolithic Power Systems (MPS). Le MP2672A a une structure d'alimentation CC à tension étroite (NVDC) et surveille la tension sur chaque cellule, égalisant les tensions de la cellule si la différence entre les deux cellules dépasse le seuil de non-concordance. Il dispose également de deux modes de fonctionnement sélectifs avec un courant de sortie configurable jusqu'à 2 A via le réglage du registre via l'interface série I2C, ainsi qu'une alimentation MP2672A sélectionnable, une indication LED et des fonctions de protection permettant un fonctionnement fiable. Cette carte Click™ est applicable à une large gamme d'applications portables, de machines de point de vente (POS), d'applications générales à deux cellules, et plus encore.
La carte Click Board™ Balancer 4 est supportée par une bibliothèque compatible mikroSDK, qui comprend des fonctions qui simplifient le développement logiciel. Cette carte Click Board™ est un produit entièrement testé, prêt à être utilisé sur un système équipé du socket mikroBUS™.
How Does The Balancer 4 Click Board™ Work?
The Balancer 4 Click Board™ as its foundation uses the MP2672A, a highly integrated and flexible switch-mode battery charger for two-cell Lithium-Ion batteries in series from Monolithic Power Systems (MPS). The MP2672A features a cell balance function that monitors the voltage across each cell and equalizes them if the difference exceeds the mismatch threshold. It features up to 2A of programmable charge current for batteries with two cells in series, alongside protections like battery temperature monitoring, programmable charging safety timer protection, JEITA-compliant battery NTC monitoring, cell over-voltage protection (OVP), thermal regulation, and thermal shutdown.
The MP2672A has a narrow voltage DC (NVDC) power structure. It automatically detects the battery voltage and charges it in three phases: pre-charge, constant current, and voltage charge. With a deeply discharged battery, the MP2672A regulates the system output to a minimum voltage level, which powers the system instantly while simultaneously charging the battery via integrated FET. It also offers flexible new charging cycle initiation compatible with Standalone mode and Host-control mode of operation selectable through an onboard switch labelled as HOST SEL.
Diverse and robust protections include a thermal regulation loop to decrease the charge current if the junction temperature exceeds the thermal loop threshold and battery temperature protection compliant with JEITA standards. Other safety features include input over-voltage protection (OVP), battery OVP, thermal shutdown, battery temperature monitoring, and a configurable backup timer to prevent prolonged charging of a dead battery.
Balancer 4 Click Board™ communicates with MCU using the standard I2C 2-Wire interface to read data and configure settings, supporting a Standard Mode operation up to 100kHz. It also has two LED indicators, red and green, marked with CHARGE and POWER, which can visually show the existence of a valid power supply to the MP2672A and the active status of the battery charging process. Also, an NTC function is available for temperature-qualified charging, where the MP2672A continuously monitors the battery's temperature by measuring the voltage on the onboard NTC header pins.
The Balancer 4 Click Board™ can operate with both 3.3V and 5V logic voltage levels selected via the VCC SEL jumper. It allows both 3.3V and 5V capable MCUs to use the communication lines properly. Additionally, there is a possibility for the MP2672A power supply selection via jumper labelled as VIN SEL to supply the MP2672A from an external power supply terminal in the range from 4V to 5.75V or with 5V voltage level from mikroBUS™ power rail. However, the Click board™ comes equipped with a library containing easy-to-use functions and an example code that can be used, as a reference, for further development.
SPECIFICATIONS
| Type | Battery charger |
| Applications | Can be used for portable applications, Point-of-Sale (POS) machines, general two-cell applications, and more |
| On-board modules | MP2672A - highly integrated and flexible switch-mode battery charger from Monolithic Power Systems (MPS) |
| Key Features | Two-cell Lithium-Ion batteries in series, up to 2A configurable charge current, compatible with Host-control or Standalone mode, NVDC power path management, integrated cell-balancing circuit for mismatched cells, status indicators, I2C interface, NTC, and more |
| Interface | I2C |
| Compatibility | mikroBUS |
| Click board size | L (57.15 x 25.4 mm) |
| Input Voltage | 3.3V or 5V,External |
PINOUT DIAGRAM
This table shows how the pinout of the Balancer 4 Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| NC | 1 | AN | PWM | 16 | NC | ||
| NC | 2 | RST | INT | 15 | NC | ||
| NC | 3 | CS | RX | 14 | NC | ||
| NC | 4 | SCK | TX | 13 | NC | ||
| NC | 5 | MISO | SCL | 12 | SCL | I2C Clock | |
| NC | 6 | MOSI | SDA | 11 | SDA | I2C Data | |
| Power Supply | 3.3V | 7 | 3.3V | 5V | 10 | 5V | Power Supply |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
ONBOARD SETTINGS AND INDICATORS
| Label | Name | Default | Description |
|---|---|---|---|
| LD1 | PWR | - | Power LED Indicator |
| LD2 | POWER | - | MP2672A Valid Supply LED Indicator |
| LD3 | CHARGE | - | Charge Status LED Indicator |
| JP1 | VCC SEL | Left | Logic Level Voltage Selection 3V3/5V: Left position 3V3, Right position 5V |
| JP2 | VIN SEL | Right | MP2672A Power Supply Selection 5V/EXT: Left position 5V, Right position EXT |
| J1 | NTC | Unpopulated | External Thermistor Connection Header |
| SW1 | HOST MODE | Right | Operation Mode Selection |
BALANCER 4 CLICK ELECTRICAL SPECIFICATIONS
| Description | Min | Typ | Max | Unit |
|---|---|---|---|---|
| Supply Voltage | 3.3 | - | 5 | V |
| External Supply Voltage VIN | 4 | - | 5.75 | V |
| Battery Pack Voltage | - | - | 9 | V |
| Output Current | - | - | 2 | A |
| Operating Temperature Range | -40 | +25 | +120 | °C |
Software Support
We provide a library for the Balancer 4 Click Board™ and a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
The package can be downloaded/installed directly from NECTO Studio The package Manager (recommended), downloaded from our LibStock™ or found on the MikroE Github account.
Library Description
This library contains API for the Balancer 4 Click Board™ driver.
Key functions
-
balancer4_write_registerThis function writes a desired data byte to the selected register by using an I2C serial interface. -
balancer4_write_and_verify_registerThis function writes a desired data byte to the selected register and verifies if it is written correctly by reading it. -
balancer4_read_registerThis function reads a data byte from the selected register by using an I2C serial interface.
Example Description
This example demonstrates the use of the Balancer 4 Click Board™ by configuring the Click Board™ for charging and then reading the status and fault registers.
void application_task ( void )
{
uint8_t status, fault;
if ( BALANCER4_OK == balancer4_read_register ( &balancer4, BALANCER4_REG_STATUS, &status ) )
{
log_printf ( &logger, "rn - STATUS - rn", status );
log_printf ( &logger, " Battery status: " );
if ( status & BALANCER4_STATUS_BATTERY_MISSING )
{
log_printf ( &logger, "missingrn" );
}
else
{
log_printf ( &logger, "presentrn" );
log_printf ( &logger, " Charging status: " );
switch ( status & BALANCER4_STATUS_CHG_STAT_MASK )
{
case BALANCER4_STATUS_NOT_CHARGING:
{
log_printf ( &logger, "not chargingrn" );
break;
}
case BALANCER4_STATUS_PRE_CHARGE:
{
log_printf ( &logger, "pre-chargern" );
break;
}
case BALANCER4_STATUS_CONSTANT_CHARGE:
{
log_printf ( &logger, "constant current or constant voltage chargern" );
break;
}
case BALANCER4_STATUS_CHARGING_COMPLETE:
{
log_printf ( &logger, "charging completern" );
break;
}
}
}
}
if ( BALANCER4_OK == balancer4_read_register ( &balancer4, BALANCER4_REG_FAULT, &fault ) )
{
if ( fault )
{
log_printf ( &logger, "rn - FAULT - rn" );
if ( fault & BALANCER4_FAULT_WD )
{
log_printf ( &logger, " The watchdog timer has expiredrn" );
}
if ( fault & BALANCER4_FAULT_INPUT )
{
log_printf ( &logger, " Input OVP has occuredrn" );
}
if ( fault & BALANCER4_FAULT_THERMAL_SD )
{
log_printf ( &logger, " Thermal shutdownrn" );
}
if ( fault & BALANCER4_FAULT_TIMER )
{
log_printf ( &logger, " The safety timer has expiredrn" );
}
if ( fault & BALANCER4_FAULT_BAT )
{
log_printf ( &logger, " Battery OVP has occuredrn" );
}
switch ( fault & BALANCER4_FAULT_NTC_MASK )
{
case BALANCER4_FAULT_NTC_COLD:
{
log_printf ( &logger, " An NTC cold fault has occuredrn" );
break;
}
case BALANCER4_FAULT_NTC_COOL:
{
log_printf ( &logger, " An NTC cool fault has occuredrn" );
break;
}
case BALANCER4_FAULT_NTC_WARM:
{
log_printf ( &logger, " An NTC warm fault has occuredrn" );
break;
}
case BALANCER4_FAULT_NTC_HOT:
{
log_printf ( &logger, " An NTC hot fault has occuredrn" );
break;
}
}
}
}
Delay_ms ( 500 );
}
The complete application code and ready-to-use projects can be installed directly from NECTO Studio The package Manager (recommended), downloaded from our LibStock™ or found on the MikroE Github account.
Other MikroE Libraries used in the example:
- MikroSDK.Board
- MikroSDK.Log
- Click.Balancer4
Additional Notes and Information
Depending on the development board you are using, you may need a USB UART Click Board™, USB UART 2 Click, or RS232 Click to connect to your PC for development systems with no UART to USB interface available on the board. UART terminal is available in all MikroElektronika compilers.
MIKROSDK
The Balancer 4 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Planche à 4 clics Balancer
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.