Mikroelektronika d.o.o.
Carte RS232 3 Click
Carte RS232 3 Click
Impossible de charger la disponibilité du service de retrait
Key Features:
- Normes EIA/TIA-232-F, circuit AUTO ON-LINE® qui se réveille automatiquement après un arrêt, débit de données minimum de 250 kbps sous charge, pompe de charge régulée produisant des sorties RS-232 stables quelle que soit l'alimentation électrique, et bien plus encore
- Basé sur le P3221E - émetteur-récepteur RS232 basse consommation de MaxLinear
- Peut être utilisé pour les communications série à faible consommation, les appareils série portables, les équipements de point de vente et de nombreuses autres applications
- mikroBUS : interface UART
La carte RS232 3 Click Board™ est une carte complémentaire compacte représentant un émetteur-récepteur RS232 utilisable de manière universelle. Cette carte comprend le SP3221E, un émetteur-récepteur RS232 à faible consommation de MaxLinear. Le SP3221E utilise une alimentation interne à pompe de charge à haut rendement et est conforme aux normes EIA/TIA-232-F lorsqu'il est alimenté par l'un des rails d'alimentation mikroBUS™. La fonction AUTO ON-LINE® permet au SP3221E de se « réveiller » automatiquement à partir d'un état d'arrêt lorsqu'un câble RS232 est connecté et qu'un périphérique est allumé. Lorsqu'il n'est pas connecté ou qu'il n'est pas utilisé, le SP3221E s'éteint automatiquement, consommant moins de courant d'alimentation. Cette carte Click™ convient aux communications série à faible consommation, aux appareils série portables, aux équipements de point de vente et à de nombreuses autres applications.
La carte RS232 3 Click Board™ est prise en charge par une bibliothèque compatible mikroSDK, qui comprend des fonctions qui simplifient le développement logiciel. Cette carte Click™ est livrée sous la forme d'un produit entièrement testé, prêt à être utilisé sur un système équipé de la prise mikroBUS™.
How Does The RS232 3 Click Board™ Work?
The RS232 3 Click Board™ as its foundation uses the SP3221E, a low power, RS232 transceiver (single driver/single receiver) solution with a 250kbps data rate from MaxLinear. The SP3221E uses an internal high-efficiency, charge-pump power supply and is compliant with EIA/TIA-232-F standards when powered by any of the mikroBUS™ power rails. This charge pump and MaxLinear's driver architecture allow the SP3221E to deliver compliant RS-232 performance from a single power supply intended for portable or handheld applications such as embedded computers, data logging devices, medical diagnostics, and remote sensors.
The SP3221E communicates with MCU using the UART interface with the default baud rate of 115200bps for the data transfer. It also comes equipped with the standard DB-9 connector, which makes interfacing with the RS232 simple and easy, and a red LED indicator labelled as STATUS that indicates whether a valid RS232 signal is present not. This signal is also routed to the INT pin of the mikroBUS™ socket, labelled as STA. Alongside UART communication, several signals connected to the mikroBUS™ socket pins are also used to forward the information to the MCU.
For proper operation of SP3221E, this board uses a combination of two pins, EN and SHD pins routed to the CS and RST pins of the mikroBUS™ socket. The receiver is active when the AUTO ON-LINE® circuitry is enabled or when in Shutdown. The AUTO ON-LINE® feature, controlled via ON pin routed to the PWM pin of the mikroBUS™ socket, allows the SP3221E to automatically "Wake-Up" from a Shutdown state when an RS232 cable is connected, and a peripheral device is turned on. During the Shutdown, the receiver will continue to be active. If there is no activity at the receiver for a more extended period or when the SHD pin is enabled, the device goes into a Standby mode. Also, driving the EN pin to a high state forces the receiver's output into a high impedance state.
The RS232 3 Click Board™ can operate with both 3.3V and 5V logic voltage levels selected via the VCC SEL jumper. This way, it is allowed for both 3.3V and 5V capable MCUs to use the communication lines properly. However, the Click board™ comes equipped with a library that contains easy-to-use functions and an example code that can be used, as a reference, for further development.
SPECIFICATIONS
| Type | RS232 |
| Applications | The RS232 3 Click Board™ can be used for low-power serial communications, portable serial devices, point-of-sale equipment, and many more applications |
| On-board modules | SP3221E - low-power RS232 transceiver from MaxLinear |
| Key Features | EIA/TIA-232-F standards, AUTO ON-LINE® circuitry automatically wakes up from a shutdown, minimum 250kbps data rate under load, Regulated charge pump yields stable RS-232 outputs regardless of power supply, and more |
| Interface | UART |
| Compatibility | mikroBUS |
| Click board size | L (57.15 x 25.4 mm) |
| Input Voltage | 3.3V or 5V |
PINOUT DIAGRAM
This table shows how the pinout of the RS232 3 Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| NC | 1 | AN | PWM | 16 | ON | AUTO ON-LINE® | |
| Shutdown | SHD | 2 | RST | INT | 15 | STA | RS232 Signal Status |
| Enable | EN | 3 | CS | RX | 14 | TX | UART TX |
| NC | 4 | SCK | TX | 13 | RX | UART RX | |
| NC | 5 | MISO | SCL | 12 | NC | ||
| NC | 6 | MOSI | SDA | 11 | NC | ||
| Power Supply | 3.3V | 7 | 3.3V | 5V | 10 | 5V | Power Supply |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
ONBOARD SETTINGS AND INDICATORS
| Label | Name | Default | Description |
|---|---|---|---|
| LD1 | PWR | - | Power LED Indicator |
| LD2 | STATUS | - | Valid RS232 Signal LED Indicator |
| JP1 | VCC SEL | Left | Logic Level Voltage Selection 3V3/5V: Left position 3V3, Right position 5V |
RS232 3 CLICK ELECTRICAL SPECIFICATIONS
| Description | Min | Typ | Max | Unit |
|---|---|---|---|---|
| Supply Voltage | 3.3 | - | 5 | V |
| Data Rate | 250 | - | - | kbps |
| Operating Temperature Range | -40 | +25 | +85 | °C |
Software Support
We provide a library for the RS232 3 Click Board™ as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
The package can be downloaded/installed directly from NECTO Studio The package Manager (recommended), downloaded from our LibStock™or found on the MikroE Github account.
Library Description
This library contains API for RS232 3 Click driver.
Key functions
-
rs2323_generic_writeThis function writes a desired number of data bytes by using UART serial interface. -
rs2323_generic_readThis function reads a desired number of data bytes by using UART serial interface.
Example Description
This example demonstrates the use of the RS232 3 Click Board™ by showing the communication between the two click board configured as a receiver and transmitter.
void application_task ( void )
{
#ifdef DEMO_APP_TRANSMITTER
rs2323_generic_write( &rs2323, DEMO_TEXT_MESSAGE, strlen( DEMO_TEXT_MESSAGE ) );
log_printf( &logger, "%s", ( char * ) DEMO_TEXT_MESSAGE );
Delay_ms( 3000 );
#else
uint8_t rx_data;
if ( rs2323_generic_read( &rs2323, &rx_data, 1 ) > 0 )
{
log_printf( &logger, "%c", rx_data );
}
#endif
}
The full application code, and ready to use projects can be installed directly from NECTO Studio The package Manager (recommended), downloaded from our LibStock™or found on MikroE Github account.
Other MikroE Libraries used in the example:
- MikroSDK.Board
- MikroSDK.Log
- Click.RS2323
Additional Notes and Information
Depending on the development board you are using, you may need a USB UART click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MikroElektronika compilers.
MIKROSDK
The RS232 3 Click Board™ is supported with mikroSDK- MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Carte RS232 3 Click
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.