Mikroelektronika d.o.o.
Tableau de clic Accel 16
Tableau de clic Accel 16
Impossible de charger la disponibilité du service de retrait
Le Tableau à clic Accel 16™ est une carte complémentaire compacte qui contient un capteur d'accélération. Cette carte comprend l'ADXL363, une combinaison de trois capteurs micro-puissants comprenant l'accélération et la température d'Analog Devices. Ce dispositif combine un accéléromètre MEMS à 3 axes, un capteur de température et une entrée de convertisseur analogique-numérique (ADC) pour les conversions synchronisées de signaux externes. Il permet des mesures d'accélération à pleine échelle sélectionnables dans des plages de ±2g, ±4g et ±8g (avec une résolution de 1mg/LSB sur la plage ±2g), et communique via une interface série SPI offrant une résolution de sortie de 12 bits pour les trois capteurs.
Le tableau de bord Accel 16 Click Board™ convient à diverses applications telles que la surveillance des vibrations et de l'état, les tests et les mesures, la maintenance prédictive, etc.
How Does The Accel 16 Click Board™ Work?
The Accel 16 Click Board™ as its foundation uses the ADXL363, a micropower complete sensor suite consisting of an accelerometer, an ADC for synchronous conversion of input from a third sensor, and a temperature sensor from Analog Devices. It measures both dynamic accelerations, resulting from motion or shock, and static acceleration, such as tilt, and allows selectable full-scale acceleration measurements in ranges of ±2g, ±4g, and ±8g (with a resolution of 1mg/LSB on the ±2g range). Acceleration is reported digitally, and the device communicates via the SPI protocol providing 12-bit output resolution for all three sensors.
The ADXL363 has two operating modes: Measurement mode for continuous, wide-bandwidth sensing; and Wake-up mode for limited bandwidth activity detection. Measurement mode represents its normal operating mode, and in this mode, acceleration data is read continuously, while the Wake-Up mode is ideal for simple detection of the presence or absence of motion at low power consumption. Wake-up mode helps implement a motion-activated ON/OFF switch, allowing the rest of the system to Power-Down until the activity is detected. In addition, measurement is suspended altogether by placing the device in Standby mode, reducing current consumption. During Standby, pending interrupts and data are preserved, and no new interrupts are generated.
In addition to a built-in accelerometer and temperature sensor, which the user can use to monitor internal system temperature or improve the device's temperature stability via calibration, the ADXL363 incorporates a 12-bit analog-to-digital converter (ADC) for digitization of external analog input. The ADC converts analog inputs ranging from 10% to 90% of the supply voltage and is best suited for use with a sensor input due to its synchronization with the accelerometer and temperature sensor.
The ADXL363 communicates with MCU through a standard SPI interface that enables clock speeds up to 8MHz, supporting the most common SPI mode - SPI Mode 0. This Click board™ also possesses two interrupt pins, INT1 and INT2, routed to the INT and PWM pins on the mikroBUS™, which above all have a dual function. First, they can be used as classic interrupt pins to signal MCU that an event has been sensed or can be used, e.g., INT1 as an input for external clocking and INT2 as input for synchronized sampling. One or both of these alternate functions can be used concurrently; however, if an interrupt pin is used for its alternate function, it cannot simultaneously be used for its primary function, to signal interrupts.
The Accel 16 Click Board™ can be operated only with a 3.3V logic voltage level. The board must perform appropriate logic voltage level conversion before use with MCUs with different logic levels. However, the Click board™ comes equipped with a library containing functions and an example code that can be used, as a reference, for further development.
SPECIFICATIONS
| Type | Motion |
| Applications | The Accel 16 Click Board™ be used for various applications such as vibration and condition monitoring, test and measurements, predictive maintenance, and more |
| On-board modules | ADXL363 - micropower complete sensor suite consisting of an accelerometer, an ADC for synchronous conversion of input from a third sensor, and a temperature sensor from Analog Devices |
| Key Features | Accelerometer, temperature sensor, and provision for third analog sensor input, low power consumption, all sensors sampled synchronously, 12-bit resolution for all sensors, built-in features for motion-based system level power savings, and more |
| Interface | SPI |
| Compatibility | mikroBUS |
| Click board size | S (28.6 x 25.4 mm) |
| Input Voltage | 3.3V |
PINOUT DIAGRAM
This table shows how the pinout on Accel 16 Click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| NC | 1 | AN | PWM | 16 | IN2 | Interrupt 2 | |
| NC | 2 | RST | INT | 15 | IN1 | Interrupt 1 | |
| SPI Chip Select | CS | 3 | CS | RX | 14 | NC | |
| SPI Clock | SCK | 4 | SCK | TX | 13 | NC | |
| SPI Data OUT | SDO | 5 | MISO | SCL | 12 | NC | |
| SPI Data IN | SDI | 6 | MOSI | SDA | 11 | NC | |
| Power Supply | 3.3V | 7 | 3.3V | 5V | 10 | NC | |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
ONBOARD SETTINGS AND INDICATORS
| Label | Name | Default | Description |
|---|---|---|---|
| LD1 | PWR | - | Power LED Indicator |
ACCEL 16 CLICK ELECTRICAL SPECIFICATIONS
| Description | Min | Typ | Max | Unit |
|---|---|---|---|---|
| Supply Voltage | - | 3.3 | - | V |
| Acceleration Range | ±2 | - | ±8 | g |
| Sensitivity | 1000 | - | 250 | LSB/g |
| Resolution | - | 12 | - | bits |
| Operating Temperature Range | -40 | +25 | +85 | °C |
Software Support
We provide a library for the Accel 16 Click Board™ as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
The package can be downloaded/installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe Github account.
Library Description
This library contains API for the Accel 16 Click Board™ driver.
Key functions
-
accel16_get_axesGet axes data. -
accel16_filter_configurationFilter configuration. -
accel16_get_temperatureGet temperature data.
Example Description
This showcases ability of the Accel 16 Click Board™ to read x, y, and z axes data in different resolution, read IC temperature and also have additional functionality to read ADC data. Device also has ability to store data in internal fifo buffer.
void application_task ( void )
{
if ( ACCEL16_APPLICATION_FIFO == accel16.application_type )
{
accel16_read_fifo_data( );
}
else if ( ACCEL16_APPLICATION_REG == accel16.application_type )
{
accel16_read_reg_data( );
}
log_printf( &logger, "********************************************************rn" );
Delay_ms( 300 );
}
The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe github account.
Other Mikroe Libraries used in the example:
- MikroSDK.Board
- MikroSDK.Log
- Click.Accel16
Additional Notes and Information
Depending on the development board you are using, you may need a USB UART click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MikroElektronika compilers.
MIKROSDK
The Accel 16 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Tableau de clic Accel 16
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.