Mikroelektronika d.o.o.
Tableau de clic Accel 17
Tableau de clic Accel 17
Impossible de charger la disponibilité du service de retrait
Le Tableau à clic Accel 17™ est une carte complémentaire compacte qui contient un capteur d'accélération. Cette carte comprend le MXC62320MP, un accéléromètre à deux axes à sortie numérique à faible consommation fabriqué selon un processus CMOS submicronique standard de MEMSIC. Le MXC62320MP peut mesurer à la fois l'accélération dynamique (par exemple, les vibrations) et l'accélération statique (par exemple, la gravité), avec des mesures d'accélération à grande échelle, une plage de ±2g et une interface hôte configurable qui prend en charge la communication série I2C avec un fonctionnement en mode rapide à 400 kHz.
Le tableau à clic Accel 17™ convient à diverses applications telles que la surveillance des vibrations et de l'état, les tests et les mesures, la maintenance prédictive, etc.
How Does The Accel 17 Click Board™ Work?
The Accel 17 Click Board™ as its foundation uses the MXC62320MP, a complete dual-axis acceleration measurement system fabricated on a monolithic CMOS process from MEMSIC. The MXC62320MP operation is based on heat transfer by natural convection and operates like other accelerometers, except it is a gas in the MEMSIC sensor. It can measure both dynamic acceleration (e.g., vibration) and static acceleration (e.g., gravity), with full-scale acceleration measurements, a range of ±2g. It also comes with embedded Power Up/Down and self-test function, resolution better than 1mg, and >50.000g shock survival rating. In addition to all these features, it also has excellent temperature stability and low power consumption/low active current.
This accelerometer can enter a Power-Down mode writing a command [xxxxxxx1] into the accelerometer's internal register, while a Wake-Up operation is performed when a command of [xxxxxxx0] is written into the same register. Note that the MXC62320MP needs about 75ms (typical) for Power-Up time.
The Accel 17 Click Board™ communicates with MCU using a standard I2C 2-Wire interface that supports 400kHz Fast Mode operation. Since the sensor for operation requires a 3.3V logic voltage level only, this Click board™ also features the PCA9306 voltage-level translator from Texas Instruments. The I2C interface bus lines are routed to the dual bidirectional voltage-level translator, allowing this Click board™ to work with both 3.3V and 5V MCUs properly.
TheAccel 17 Click Board™ can operate with both 3.3V and 5V logic voltage levels selected via the VIO SEL jumper. This way, it is allowed for both 3.3V and 5V capable MCUs to use the I2C communication lines properly. However, the Click board™ comes equipped with a library that contains easy-to-use functions and an example code that can be used, as a reference, for further development.
SPECIFICATIONS
| Type | Motion |
| Applications | Can be used for various applications such as vibration and condition monitoring, test and measurements, predictive maintenance, and more |
| On-board modules | MXC62320MP - low-power digital output dual-axis accelerometer fabricated on a standard, submicron CMOS process from MEMSIC |
| Key Features | Low power consumption, ±2 g dual axis accelerometer, embedded power up/down and self-test function, integrated temperature sensor and mixed signal processing, resolution better than 1mg, and more |
| Interface | I2C |
| Compatibility | mikroBUS |
| Click board size | S (28.6 x 25.4 mm) |
| Input Voltage | 3.3V or 5V |
Pinout Diagram
This table shows how the pinout on the Accel 17 Click Board™corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| NC | 1 | AN | PWM | 16 | NC | ||
| NC | 2 | RST | INT | 15 | NC | ||
| NC | 3 | CS | RX | 14 | NC | ||
| NC | 4 | SCK | TX | 13 | NC | ||
| NC | 5 | MISO | SCL | 12 | SCL | I2C Clock | |
| NC | 6 | MOSI | SDA | 11 | SDA | I2C Data | |
| Power Supply | 3.3V | 7 | 3.3V | 5V | 10 | 5V | Power Supply |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
ONBOARD SETTINGS AND INDICATORS
| Label | Name | Default | Description |
|---|---|---|---|
| LD1 | PWR | - | Power LED Indicator |
| JP1 | VIO SEL | Left | Logic Level Voltage Selection 3V3/5V: Left position 3V3, Right position 5V |
ACCEL 17 CLICK ELECTRICAL SPECIFICATIONS
| Description | Min | Typ | Max | Unit |
|---|---|---|---|---|
| Supply Voltage | 3.3 | - | 5 | V |
| Acceleration Range | - | ±2 | - | g |
| Sensitivity | - | 512 | - | LSB/g |
| Operating Temperature Range | -40 | +25 | +85 | °C |
Software Support
We provide a library for the Accel 17 Click Board™ as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
The package can be downloaded/installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe GitHub account.
Library Description
This library contains an API for the Accel 17 Click Board™ driver.
Key Functions
accel17_get_axes_data- Accel data reading.accel17_generic_read- Reading function.accel17_generic_write- Writing function.
Example Description
This example showcases the ability of the device to read x, y-axis orientation.
void application_task ( void )
{
accel17_axes_t axes;
accel17_get_axes_data ( &accel17, &axes );
log_printf( &logger, " > X[degree]: %.2frn > Y[degree]: %.2frn", axes.x, axes.y );
log_printf( &logger, "*********************************rn" );
Delay_ms( 300 );
}
The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe GitHub account.
Other Mikroe Libraries used in the example:
- MikroSDK.Board
- MikroSDK.Log
- Click.Accel17
Additional Notes and Information
Depending on the development board you are using, you may need a USB UART click, USB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.
MIKROSDK
The Accel 17 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Tableau de clic Accel 17
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.