Mikroelektronika d.o.o.
Panneau à clic CO2
Panneau à clic CO2
Impossible de charger la disponibilité du service de retrait
La carte Click Board™ CO2 est une carte complémentaire compacte qui contient le capteur miniature de CO₂ de Sensirion. Cette carte comprend le STC31, un capteur de concentration de gaz conçu pour les applications à volume élevé. Le STC31 utilise un principe de mesure de conductivité thermique révolutionnaire, qui se traduit par une répétabilité supérieure et une stabilité à long terme. Les performances exceptionnelles de ces capteurs sont basées sur la technologie de capteur brevetée CMOSens® de Sensirion, qui combine l'élément capteur, le traitement du signal et l'étalonnage numérique sur une petite puce CMOS. Il dispose d'une interface numérique I2C, ce qui facilite la connexion directe au MCU. Cette carte Click™ représente un choix idéal pour la surveillance sanitaire, environnementale, industrielle et résidentielle des concentrations élevées de CO2 et des applications où la fiabilité est cruciale.
La carte Click Board™ CO2 est supportée par une bibliothèque compatible mikroSDK, qui comprend des fonctions qui simplifient le développement logiciel. Cette carte Click Board™ est livrée sous forme de produit entièrement testé, prêt à être utilisé sur un système équipé du socket mikroBUS™.
How Does The CO2 Click Board™ Work?
The CO2 Click Board™ as its foundation uses the STC31, a gas concentration sensor for high range, accurate CO₂ measurements designed for high-volume applications from Sensirion. The STC31 is based on a revolutionized thermal conductivity measurement principle, which results in superior repeatability and long-term stability. By relying on the thermal conductivity technology, the sensor offers an ultra-low power consumption, making the STC31 the perfect choice for applications where reliability is key.
The accuracy of the STC31 is 0.5 vol%, and ±3% of the measured value, while the sensor response time is faster than 1 second. The outstanding performance of these sensors is based on Sensirion's patented CMOSens® Technology, which combines the sensor element, signal processing, and digital calibration on a small CMOS chip. The well-proven CMOSens® Technology represents the ideal choice for demanding and cost-sensitive OEM applications.
The CO2 Click Board™ communicates with MCU using the standard I2C 2-Wire interface to read data and configure settings, supporting Standard Mode operation with a clock frequency up to 100kHz, Fast Mode up to 400kHz, and Fast Mode Plus up to 1MHz. Besides, it also allows the choice of the three least significant bits of its I2C slave address by positioning the SMD jumper labelled as ADDR SEL to an appropriate position providing the user with a choice of 4 I2C Slave addresses.
The CO2 Click Board™ can operate with both 3.3V and 5V logic voltage levels selected via the VCC SEL jumper. This way, it is allowed for both 3.3V and 5V capable MCUs to use the I2C communication lines properly. However, the Click board™ comes equipped with a library containing easy-to-use functions and an example code that can be used, as a reference, for further development.
SPECIFICATIONS
| Type | Gas |
| Applications | The CO2 Click Board™ be used for health, environmental, industrial, residential monitoring of high CO₂ concentrations and applications where reliability is crucial |
| On-board modules | STC31 - gas concentration sensor for high range, accurate CO₂ measurements designed for high-volume applications from Sensirion |
| Key Features | Low power consumption, high reliability and long-term stability, best signal-to-noise ratio, industry-proven technology with a track record of more than 15 years, high process capability, and more |
| Interface | I2C |
| Compatibility | mikroBUS |
| Click board size | S (28.6 x 25.4 mm) |
| Input Voltage | 3.3V or 5V |
PINOUT DIAGRAM
This table shows how the pinout of the CO2 Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| NC | 1 | AN | PWM | 16 | NC | ||
| NC | 2 | RST | INT | 15 | NC | ||
| NC | 3 | CS | RX | 14 | NC | ||
| NC | 4 | SCK | TX | 13 | NC | ||
| NC | 5 | MISO | SCL | 12 | SCL | I2C Clock | |
| NC | 6 | MOSI | SDA | 11 | SDA | I2C Data | |
| Power Supply | 3.3V | 7 | 3.3V | 5V | 10 | 5V | Power Supply |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
ONBOARD SETTINGS AND INDICATORS
| Label | Name | Default | Description |
|---|---|---|---|
| LD1 | PWR | - | Power LED Indicator |
| JP1 | VCC SEL | Left | Logic Level Voltage Selection 3V3/5V: Left position 3V3, Right position 5V |
| JP2 | ADDR SEL | Lower | I2C Address Selection: Left position 0x2C, Right position 0x2A, Upper position 0x2B, Lower position 0x29 |
CO2 CLICK ELECTRICAL SPECIFICATIONS
| Description | Min | Typ | Max | Unit |
|---|---|---|---|---|
| Supply Voltage | 3.3 | - | 5 | V |
| Selectable Measurement Range (N2 / Air) | 0 | - | 25/100 | vol% |
| Accuracy | - | ±0.5 | - | % |
| Resolution | - | 16 | - | bit |
| Operating Temperature Range | -20 | +25 | +85 | °C |
Software Support
We provide a library for the CO2 Click Board™ as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
The package can be downloaded/installed directly from NECTO Studio The package Manager (recommended), downloaded from our LibStock™ or found on MikroE Github account.
Library Description
This library contains API for the CO2 Click Board™ driver.
Key functions
-
co2_get_idRead device and serial ID's. -
co2_set_referenceSet device reference values for gas calculation. -
co2_read_gasRead CO₂ concentration and temperature value.
Example Description
This example showcases ability of the CO2 Click Board™. It reads ID's configures device for operation work and reads CO₂ gas concentration in air and temperature of IC every second.
void application_task ( void )
{
float gas_data = 0;
float temp_data = 0;
if ( CO2_OK == co2_read_gas( &co2, &gas_data, &temp_data ) )
{
log_printf( &logger, " > CO2[%%]: %.2frn", gas_data );
log_printf( &logger, " > Temperature[degC]: %.2frn", temp_data );
Delay_ms( 1000 );
}
Delay_ms( 1 );
}
The full application code, and ready to use projects can be installed directly from NECTO Studio The package Manager (recommended), downloaded from our LibStock™ or found on MikroE Github account.
Other MikroE Libraries used in the example:
- MikroSDK.Board
- MikroSDK.Log
- Click.CO2
Additional Notes and Information
Depending on the development board you are using, you may need a USB UART Click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MikroElektronika compilers.
MIKROSDK
The CO2 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Software Support
We provide a library for the CO2 Click Board™ as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
The package can be downloaded/installed directly from NECTO Studio The package Manager (recommended), downloaded from our LibStock™ or found on MikroE Github account.
Library Description
This library contains API for the CO2 Click Board™ driver.
Key functions
-
co2_get_idRead device and serial ID's. -
co2_set_referenceSet device reference values for gas calculation. -
co2_read_gasRead CO₂ concentration and temperature value.
Example Description
This example showcases ability of the CO2 Click Board™. It reads ID's configures device for operation work and reads CO₂ gas concentration in air and temperature of IC every second.
void application_task ( void )
{
float gas_data = 0;
float temp_data = 0;
if ( CO2_OK == co2_read_gas( &co2, &gas_data, &temp_data ) )
{
log_printf( &logger, " > CO2[%%]: %.2frn", gas_data );
log_printf( &logger, " > Temperature[degC]: %.2frn", temp_data );
Delay_ms( 1000 );
}
Delay_ms( 1 );
}
The full application code, and ready to use projects can be installed directly from NECTO Studio The package Manager (recommended), downloaded from our LibStock™ or found on MikroE Github account.
Other MikroE Libraries used in the example:
- MikroSDK.Board
- MikroSDK.Log
- Click.CO2
Additional Notes and Information
Depending on the development board you are using, you may need a USB UART Click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MikroElektronika compilers.
MIKROSDK
The CO2 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Panneau à clic CO2
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.