Mikroelektronika d.o.o.
Carte à clic pour moteur à courant continu 10
Carte à clic pour moteur à courant continu 10
Impossible de charger la disponibilité du service de retrait
Le DC Motor 10 Click Board™ est un driver de moteur à courant continu à balais avec limitation et détection de courant. Il est basé sur le TLE 6208-6 G, un circuit intégré Hex-Half-Bridge / Double Six-Driver, optimisé pour les applications de pilotage de moteurs. Il peut être utilisé avec une interface de communication SPI, permettant de piloter les moteurs connectés de trois manières différentes : il peut être utilisé comme un commutateur librement configurable, un demi-pont ou un pont en H, offrant des options supplémentaires de contrôle de vitesse et de direction. Le TLE 6208-6 G contient également un ensemble de fonctions de protection, offrant un très haut niveau de fiabilité.
Outre les capacités de conduite, le DC Motor 10 Click Board™ peut également détecter la consommation de courant à sa sortie.
How Does The DC Motor 10 Click Board™ Work?
The DC Motor 10 Click Board™ is optimized for driving brushed DC motors. it integrates an efficient H-Bridge with very low ON resistance of approximately 0.8Ω through each branch. Furthermore the build-in features like Over- and Undervoltage-Lockout, Over- Temperature-Protection and the very low quiescent current in stand-by mode opens a wide range of automotive- and industrial-applications. DC Motor 10 click is perfectly suited for rapid development of various DC motor driving applications, including home appliances, printers, industrial equipment, mechatronic applications, etc.
.jpg)
The DC Motor 10 Click Board™ is based on the TLE 6208-6 G, which is a fully protected Hex-Half-Bridge-Driver designed specifically for automotive and industrial motion control applications, from Infineon Technologies AG. The part is based on Infineons Smart Power Technology SPT® which allows bipolar and CMOS control circuitry in accordance with DMOS power devices existing on the same monolithic circuitry. The six low and high side drivers are freely configurable and can be controlled separately. Therefore all kind of loads can be combined. In motion control up to 5 actuators (DCMotors) can be connected to the 6 halfbridge-outputs (cascade configuration). Operation modes forward (cw), reverse (ccw), brake and high impedance are controlled from a standard SPI-Interface. The possibility to control the outputs via software from a central logic, allows limiting the power dissipation.
The internal logic of TLE 6208-6 G is supplied by the VCC voltage, typ. with 5 V. The VCC voltage uses an internally generated Power-On Reset (POR) to initialize the module at power-on. The advantage of this system is that information stored in the logic remains intact in the event of short term failures in the supply voltage VS. The system can therefore continue to operate following VS undervoltage, without having to be reprogrammed. The "undervoltage" information is stored, and can be read out via the interface.
The DC Motor 10 Click Board™ can operate with 5V MCUs only, it is set to work over the I2C by default, and it is already equipped with the pull-up resistors. It is ready to be used as soon as it is inserted into a mikroBUS™ socket of the development system.
SPECIFICATIONS
| Type | Brushed |
| Applications | The DC Motor 10 Click Board™ is perfectly suited for rapid development of various DC motor driving applications, including home appliances, printers, industrial equipment, mechatronic applications, etc. |
| On-board modules | TLE 6208-6 G - a fully protected Hex-Half-Bridge-Driver designed specifically for automotive and industrial motion control applications, from Infineon Technologies AG |
| Key Features | Very low ON resistance of approximately 0.8Ω through each branch, build-in Over- and Undervoltage-Lockout, Over- Temperature-Protection and the very low quiescent current in stand-by mode |
| Interface | GPIO,SPI |
| Compatibility | mikroBUS |
| Click board size | M (42.9 x 25.4 mm) |
| Input Voltage | 5V |
PINOUT DIAGRAM
This table shows how the pinout of the DC Motor 10 Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| NC | 1 | AN | PWM | 16 | NC | ||
| NC | 2 | RST | INT | 15 | INH | Inhibit Input | |
| Chip Select | CS | 3 | CS | RX | 14 | NC | |
| Serial Clock | SCK | 4 | SCK | TX | 13 | NC | |
| Serial Data OUT | SDO | 5 | MISO | SCL | 12 | NC | |
| SPI Data IN | SDI | 6 | MOSI | SDA | 11 | NC | |
| 3.3V | 7 | 3.3V | 5V | 10 | 5V | Power supply | |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
ONBOARD SETTINGS AND INDICATORS
| Label | Name | Default | Description |
|---|---|---|---|
| LD1 | PWR | - | Power LED Indicator |
| LD2 | LD2 | - | External supply LED Indicator |
| J1 | - | - | Motor connection outputs |
| TB1 | PWR | - | External power supply connector |
DC MOTOR 10 CLICK ELECTRICAL SPECIFICATIONS
| Description | Min | Typ | Max | Unit |
|---|---|---|---|---|
| Input voltage | 7 | 12 | 40 | V |
| Current through the load (continuous) | 0 | 0.6 | A |
Software Support
We provide a library for the DC Motor 10 Click Board™ on our LibStock page, as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Library Description
The library covers all the necessary functions that enables the usage of the DC Motor 10 Click Board™. It initializes and defines the SPI bus driver and drivers that allow full control of the device to the user. It is possible to enable up to 6 dc motors in hlaf bridge, or 5 with full bridge.
Key Functions
void dcmotor10_resetStatusReg();- Function is used to reset status register.void dcmotor10_enableChann1();- Function is used to enable channel 1.void dcmotor10_sendCommand( uint16_t wrData );- Function is used to send command.
Example Description
The application is composed of three sections :
- System Initialization - Initializes SPI module, LOG and GPIO structures, sets INT and CS pins as output.
- Application Initialization - Initalizes SPI driver and uninhibits the device.
- Application Task - (code snippet) This example demonstrates the use of the DC Motor 10 Click Board™ by running dc motors on channels 1 through 3, first all 3 together and then separately.
void applicationTask()
{
dcmotor10_sendCommand( _DCMOTOR10_ENABLE_1 | _DCMOTOR10_ENABLE_2 | _DCMOTOR10_ENABLE_3 );
Delay_ms( 5000 );
dcmotor10_enableChann1();
Delay_ms( 5000 );
dcmotor10_enableChann2();
Delay_ms( 5000 );
dcmotor10_enableChann3();
Delay_ms( 5000 );
dcmotor10_resetStatusReg();
Delay_ms( 1000 );
}
The full application code, and ready to use projects can be found on our LibStock page.
Other mikroE Libraries used in the example:
- SPI
- UART
- Conversions
Additional Notes and Information
Depending on the development board you are using, you may need a USB UART click, USB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.
MIKROSDK
The DC Motor 10 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Software Support
We provide a library for the DC Motor 10 Click Board™ on our LibStock page, as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Library Description
The library covers all the necessary functions that enables the usage of the DC Motor 10 Click Board™. It initializes and defines the SPI bus driver and drivers that allow full control of the device to the user. It is possible to enable up to 6 dc motors in hlaf bridge, or 5 with full bridge.
Key Functions
void dcmotor10_resetStatusReg();- Function is used to reset status register.void dcmotor10_enableChann1();- Function is used to enable channel 1.void dcmotor10_sendCommand( uint16_t wrData );- Function is used to send command.
Example Description
The application is composed of three sections :
- System Initialization - Initializes SPI module, LOG and GPIO structures, sets INT and CS pins as output.
- Application Initialization - Initalizes SPI driver and uninhibits the device.
- Application Task - (code snippet) This example demonstrates the use of the DC Motor 10 Click Board™ by running dc motors on channels 1 through 3, first all 3 together and then separately.
void applicationTask()
{
dcmotor10_sendCommand( _DCMOTOR10_ENABLE_1 | _DCMOTOR10_ENABLE_2 | _DCMOTOR10_ENABLE_3 );
Delay_ms( 5000 );
dcmotor10_enableChann1();
Delay_ms( 5000 );
dcmotor10_enableChann2();
Delay_ms( 5000 );
dcmotor10_enableChann3();
Delay_ms( 5000 );
dcmotor10_resetStatusReg();
Delay_ms( 1000 );
}
The full application code, and ready to use projects can be found on our LibStock page.
Other mikroE Libraries used in the example:
- SPI
- UART
- Conversions
Additional Notes and Information
Depending on the development board you are using, you may need a USB UART click, USB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.
MIKROSDK
The DC Motor 10 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Carte à clic pour moteur à courant continu 10
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.