Mikroelektronika d.o.o.
Planche à clic Buck 7
Planche à clic Buck 7
Impossible de charger la disponibilité du service de retrait
Overview
Le Buck 7 Click Board™ est un convertisseur CC-CC abaisseur (abaisseur) à haut rendement, qui peut fournir une tension abaissée réglée numériquement sur sa sortie tout en délivrant jusqu'à 3,5 A de courant. Le Buck 7 Click Board™ accepte une large plage de tension sur son entrée - de 5 V à 35 V. La tension de sortie peut être réglée via l'interface SPI, dans la plage de 3,3 V à environ 90 % de la tension d'entrée.
Le Buck 7 Click Board™ utilise le MAX17504, un convertisseur CC-CC abaisseur synchrone haute efficacité intégré avec compensation interne, de Maxim Integrated. De plus, pour permettre le contrôle numérique de la tension de sortie, le MCP4921, un convertisseur N/A 12 bits avec interface SPI est utilisé sur la boucle de rétroaction.
The Buck 7 Click Board™ is very useful for the development of applications that require programmed reduction of the input voltage, for various purposes. Features such as the low dissipation due to high efficiency, three different operating modes, overcurrent, undervoltage and thermal protection, output voltage monitoring pin, make this Click board™ very reliable power source for a range of applications, such as the distributed power supply regulation, wall transformer regulation, single board systems, general points of load, and similar applications.
How Does The Buck 7 Click Board™ Work?
The Buck 7 Click Board™ is equipped with the MAX17504, a high efficiency, synchronous step-down DC-DC converter with internal compensation, from Maxim Integrated. This is an advanced integrated step-down converter, which requires a minimum number of external components, thanks to the internal feedback loop compensation. It utilizes a peak-current-mode control architecture, meaning that while the high side MOSFET is open and the current through the inductor ramps up, an overcurrent event will cause the MOSFET to close, preventing this current to become dangerously high. If there is a short circuit condition on the output, the device will reattempt to start after a timeout period, and if the condition is still present at the output, it will be turned off for another timeout period.
To allow adjustment of the output voltage via the SPI interface, the MCP4921, a 12bit D/A converter with SPI Interface made by Microchip, is used on the feedback loop. This DAC affects the current through the feedback loop forcing the PWM duty cycle of the internal generator, regulating the output voltage to a programmed value that way. As a result, by sending a digital value through the SPI interface to the MCP4921, it is possible to control the output voltage level in the range from 3.3V to 90% of the input voltage value.
While operating normally (PWM mode), the high and the low side MOSFETs are switched synchronously with the signal from the internal PWM generator, causing the current through the inductor to ramp up and down, regulating the output voltage that way. The lower pulse width (duty cycle) of the PWM signal, results in the lower voltage at the output.
Besides PWM mode, the device is also capable of operating in the PFM mode (Pulse Frequency Modulation). This mode allows even higher efficiency for light loads, as the low side MOSFET is completely unused. The high side MOSFET charges the inductor, letting the load drain it. During this period, the IC is in the hibernation state. This mode results in slightly more ripple at the output, with the added benefit of high efficiency for light loads. It is perfectly suited to power devices which are in the low power consumption mode (Sleep, Standby…)
The DCM mode is the compromise mode between the PWM and PFM modes. The low side MOSFET is still not used for light loads, but the PWM pulses are not skipped, and the IC constantly drives the high side MOSFET. This mode produces ripple at the output but it is slightly less efficient than the PFM mode for light loads.
Different modes are selected by the MODE pin. This pin is routed to the mikroBUS™ PWM pin (labeled as MOD), allowing the MCU to control the mode. When set to a HIGH level, the IC works in the DCM mode for light loads. When left floating, the PFM mode is selected. When it is set to the LOW logic level, the constant frequency PWM mode is set.
The #RES pin of the IC is routed to the mikroBUS™ RST pin. This pin signalizes problems with the output voltage. The pin is driven to a LOW logic level, when the output voltage drops under 92% of the nominal value, or during the thermal shutdown. It is an open drain output and it is otherwise pulled to a HIGH logic level (when not asserted)
To enable the buck converter IC, a HIGH logic level needs to be present at the EN pin of the IC, routed to the mikroBUS™ AN pin (labeled as EN). This allows the MCU to effectively control the Power ON function of the Click board™. When the IC is enabled, the LED indicator labeled as EN will indicate that the IC is activated, and the step-down conversion is in progress. Soft-start circuit prevents high inrush currents by introducing a ramp-up of the output voltage, from 0V up to the nominal value.
SPECIFICATIONS
| Type | Buck |
| Applications | A regulated power source for wide range of applications, such as the distributed power supply regulation, wall transformer regulation, single board systems, general points of load, and similar applications. |
| On-board modules | MAX17504, a high efficiency, synchronous step-down DC-DC converter with internal compensation, from Maxim Integrated; MCP4921, a 12bit D/A converter with SPI Interface, from Microchip; MCP1505, a buffered voltage reference, from Microchip. |
| Key Features | Low power dissipation due to high efficiency, three different operating modes, overcurrent, undervoltage and thermal protection, output voltage monitoring pin, output voltage set by the industry standard SPI interface. |
| Interface | SPI |
| Compatibility | mikroBUS |
| Click board size | L (57.15 x 25.4 mm) |
| Input Voltage | 5V |
ONBOARD JUMPERS AND SETTINGS
| Label | Name | Default | Description |
|---|---|---|---|
| LD1 | PWR | - | Power LED indicator |
| LD2 | EN | - | Buck enable LED indicator |
| TB1 | VIN | - | External power supply input connector |
| TB2 | VOUT | - | Regulated voltage output connector |
BUCK 7 CLICK ELECTRICAL SPECIFICATIONS
| Description | Min | Typ | Max | Unit |
|---|---|---|---|---|
| Output voltage | 3.3 | - | 30 | V |
| Input voltage | 5 | - | 35 | V |
| Output current (continuous) | 0 | - | 3.5 | A |
PINOUT DIAGRAM
This table shows how the pinout of then Buck 7 Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| Buck Enable | EN | 1 | AN | PWM | 16 | MOD | Mode Select |
| Voltage Monitor OUT | RST | 2 | RST | INT | 15 | NC | |
| Chip Select | CS | 3 | CS | RX | 14 | NC | |
| SPI Clock | SCK | 4 | SCK | TX | 13 | NC | |
| NC | 5 | MISO | SCL | 12 | NC | ||
| SPI Data IN | SDI | 6 | MOSI | SDA | 11 | NC | |
| 3.3V | 7 | 3.3V | 5V | 10 | 5V | Power Supply | |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
Software Support
We provide a demo application for the Buck 7 Click Board™ on our Libstock page, as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Library Description
The library initializes and defines the SPI bus driver. The library includes functions for enabling the IC, setting up the output voltage, as well as the functions for selecting the operating mode (PWM, PFM or DCM).
Key functions :
void buck7_setOutputVoltage(uint16_t voltage) - Function for setting up the output voltage
void buck7_enable() - Function for chip enable
void buck7_setMode(uint8_t mode) - Function for the operating mode selection
Example Description
The application is composed of three sections:
- System Initialization - Initializes SPI module and set AN, CS and PWM pin as OUTPUT
- Application Initialization - Initializes Driver, chip enable and mode selection
- Application Task - (code snippet) - Sets output voltage to 5V, 10V, 15V, 20V, 25V every 3 seconds. It is necessary to provide input voltage which is 2.7V above the programmed output voltage
void applicationTask()
{
buck7_setOutputVoltage( _BUCK7_OUT_VOLTAGE_5V );
Delay_ms( 3000 );
buck7_setOutputVoltage( _BUCK7_OUT_VOLTAGE_10V );
Delay_ms( 3000 );
buck7_setOutputVoltage( _BUCK7_OUT_VOLTAGE_15V );
Delay_ms( 3000 );
buck7_setOutputVoltage( _BUCK7_OUT_VOLTAGE_20V );
Delay_ms( 3000 );
buck7_setOutputVoltage( _BUCK7_OUT_VOLTAGE_25V );
Delay_ms( 3000 );
buck7_setOutputVoltage( _BUCK7_OUT_VOLTAGE_20V );
Delay_ms( 3000 );
buck7_setOutputVoltage( _BUCK7_OUT_VOLTAGE_15V );
Delay_ms( 3000 );
buck7_setOutputVoltage( 0x0BB8 ); /* 10 V */
Delay_ms( 3000 );
}
The full application code and ready to use projects can be found on our LibStock page.
mikroE Libraries used in the example:
- SPI
Additional Notes and Information
Depending on the development board you are using, you may need USB UART click, USB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.
MIKROSDK
The Buck 7 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant click board demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Software Support
We provide a demo application for the Buck 7 Click Board™ on our Libstock page, as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Library Description
The library initializes and defines the SPI bus driver. The library includes functions for enabling the IC, setting up the output voltage, as well as the functions for selecting the operating mode (PWM, PFM or DCM).
Key functions :
void buck7_setOutputVoltage(uint16_t voltage) - Function for setting up the output voltage
void buck7_enable() - Function for chip enable
void buck7_setMode(uint8_t mode) - Function for the operating mode selection
Example Description
The application is composed of three sections:
- System Initialization - Initializes SPI module and set AN, CS and PWM pin as OUTPUT
- Application Initialization - Initializes Driver, chip enable and mode selection
- Application Task - (code snippet) - Sets output voltage to 5V, 10V, 15V, 20V, 25V every 3 seconds. It is necessary to provide input voltage which is 2.7V above the programmed output voltage
void applicationTask()
{
buck7_setOutputVoltage( _BUCK7_OUT_VOLTAGE_5V );
Delay_ms( 3000 );
buck7_setOutputVoltage( _BUCK7_OUT_VOLTAGE_10V );
Delay_ms( 3000 );
buck7_setOutputVoltage( _BUCK7_OUT_VOLTAGE_15V );
Delay_ms( 3000 );
buck7_setOutputVoltage( _BUCK7_OUT_VOLTAGE_20V );
Delay_ms( 3000 );
buck7_setOutputVoltage( _BUCK7_OUT_VOLTAGE_25V );
Delay_ms( 3000 );
buck7_setOutputVoltage( _BUCK7_OUT_VOLTAGE_20V );
Delay_ms( 3000 );
buck7_setOutputVoltage( _BUCK7_OUT_VOLTAGE_15V );
Delay_ms( 3000 );
buck7_setOutputVoltage( 0x0BB8 ); /* 10 V */
Delay_ms( 3000 );
}
The full application code and ready to use projects can be found on our LibStock page.
mikroE Libraries used in the example:
- SPI
Additional Notes and Information
Depending on the development board you are using, you may need USB UART click, USB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.
MIKROSDK
The Buck 7 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant click board demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.