Lineeye Co Ltd
Lineeye LE-170SA CAN/LIN Line Monitor
Lineeye LE-170SA CAN/LIN Line Monitor
Couldn't load pickup availability
Key Features
- LIN Bus Monitoring in Real-Time at Same Time
- Captured Data Can be Stored on USB Stick
- CAN and LIN Bus Simulator - Ideal For Test Automation
- Up to 5 Hours Continuous Use on Internal Ni-MH Battery
The Lineeye LE-170SA is a compact hand-held line simulator/monitor for both CAN and LIN bus.
It is fitted with a touch screen for ease of use and will operate for up to 5 hours on a full charge of the internal Ni-MH cells. The unit is compact and weighs just 300g. This makes it ideal for use in the field.
The monitor has separate CAN and LIN interfaces. It can also monitor four external digital and analogue signals at the same time as monitoring CAN/LIN bus traffic. This makes it much easier to relate the data together in time. It also displays data in real-time. Data can also be stored in a plug-in USB stick.
The LE-170SA can also simulate CAN and LIN bus signals; very useful for automated testing.
Supports CAN and LIN
For CAN connect using the attached Dsub 9-pin monitor cable with a CAN bus. For LIN connect using the attached 10-pin external I/O cable or optional 5-wire prove cable (LE-5LS) with a LIN bus.
Left: CAN port Right: LIN/External signal port
Connection to CAN Bus
Connection to LIN Bus
Line Monitor Function
It monitors and displays in real time the communication frame, send/receive time (time stamp), external analog input signal, and external trigger signal condition while saving them. The saved data on the capture memory can be checked by scrolling display or search function.
It saves the logic and analog value of 4 external input. Measured data display and external analog display can be exchanged by touching the screen.
Display of Logged Analog and Digital Data
It can search the specified data from the data in capture memory. It also can count how much the data matches the condition. The search condition can be set from trigger match, errors of LIN, communication data of the specific condition, external input, and timestamp range.
Data Search Facility
Simulation Function
It can send 16 types of pre-registerd frame manually. It also can sweep (change) a part of send data by specified condition and can simulate the change of value. For LIN master mode and slave mode can are selectable.
CAN Simulation Function
CAN Packet Simulation
The Trigger with External Signals.
It can control the timer/counter or send a CAN frame by the trigger such as communication error, unusual signal from an external device, and a specified factor event.
Trigger on Packet Type
Auto Backup Function
By the function the line monitor backups the latest about 30Kbyte data to the internal SRAM capture memory (battery powered) or all the data to a external USB memory connected with the line monitor.
Auto-Backup Facility
5 Hour Battery Life
It can continuously run for 5 hours by the attached two Ni-MH batteries. You can use alkaline battery too.
Battery Compartment
Save Data in USB Flash Stick
The measured data and configuration settings can be stored into a USB flash. You can save the former and the latter part of the target data by using the trigger setting. Also by making the Auto Backup function valid, it automatically saves all the measured data to a USB flash when it finishes the measurement.
Specifications
| Interface | CAN (ISO11898) / LIN (ISO9141) |
|---|---|
| Protocol | CAN 2.0LIN (Rev. 1.1, 1.2, 1.3, 2.0, 2.1) |
| Capture Memory | 16Mbyte (acout 4000Kdata), 2 part division is available |
| Speed (bps) | CAN: 20kbps to 1Mbps LIN: 400bps to 26kbps |
| Capture memory | 16Mbyte (about 500K data). Able to divide in two. |
| Monitor function | CAN: Standard/extended format are supported, bit receiving timing can be set, filtering is available, arbitrary speed can be set. LIN: Divides the frame by specified time pass or ID setting, filtering is available, arbitrary speed can be set. |
| Simulation function | Test data transmission (data sweep is available.) |
| External Trigger | Input 1, Output 1 |
| External input | 44 Measurement of 4 signals. Range: 0 to 52V. Resolution: 12bit. Digital threshold: VIH 2.3Vmin. VIL 0.8Vmax. |
| Display | 4.3 inch TFT color display (480x272dot) 28 characters x 6-stage display |
| Touch panel | Capacitive touch screen |
| USB2.0 device port | Micro B connector |
| USB2.0 host port | Standard A connector for USB flash connection |
| Power | USB bus power 5V/500mA Two AA Ni-MH batteries or two AA alkaline batteries (LR6) |
| Drive time*1 | AA Ni-MH batteries: about 5 hours AA alkaline batteries: about 2 hours |
| Temperature & humid | 0 to 40 degrees celcius (-10 to 50 degrees celcius for storage), under 85%RH |
| Standard | 158mm x 100mm x 31mm, 300g(including batteries) |
| Size & weight | CE (class A), EMC (EN61326-1:2013) |
| Accesories | DSUB9 pin branch cable (LE-009M2), 10 pin external In/Out cable (LE-10ES1), micro USB cable, 2 AA Ni-MH batteries, utility CD, carrying bag (LEB-02), quick start guide, warranty card |
*1: Based on our testing of typical use.
Lineeye LE-170SA CAN/LIN Line Monitor
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.