Mikroelektronika d.o.o.
Barometer 5 Click Board
Barometer 5 Click Board
Verfügbarkeit für Abholungen konnte nicht geladen werden
Das Barometer 5 Click Board™ ist eine kompakte Zusatzplatine zum Messen des Luftdrucks in einer bestimmten Umgebung. Diese Platine verfügt über den MS5637-02BA03, einen hochpräzisen Niederspannungs-Luftdruck- und Temperatursensor von TE Connectivity Measurement Specialties. Der MS5637-02BA03 umfasst einen hochlinearen Drucksensor und einen 24-Bit-ΔΣ-ADC mit extrem niedrigem Stromverbrauch und internen, werkseitig kalibrierten Koeffizienten, der einen präzisen digitalen 24-Bit-Druck- und Temperaturwert sowie verschiedene Betriebsmodi bietet, die es dem Benutzer ermöglichen, die Konvertierungsgeschwindigkeit und den Stromverbrauch zu optimieren. Es verfügt über eine konfigurierbare Hostschnittstelle, die die serielle I2C-Kommunikation unterstützt und den Druck in einem Bereich von 300 mbar bis 1,2 bar mit einer Genauigkeit von ±2 mbar über einen weiten Betriebstemperaturbereich misst.
Das Barometer 5 Click Board™ eignet sich für verschiedene druckbasierte Anwendungen, insbesondere wenn ein niedriger Stromverbrauch erforderlich ist.
How Does The Barometer 5 Click Board™ Work?
The Barometer 5 Click Board™ as its foundation uses the MS5637-02BA03, a high accuracy low voltage barometric and temperature sensor from TE Connectivity Measurement Specialties, to measure air pressure in a specific environment. This new sensor module generation is based on leading MEMS technology, where the sensing principle leads to very low hysteresis and high stability of both pressure and temperature signal. It consists of a piezoresistive sensor and a sensor interface integrated circuit. The primary function of the MS5637-02BA03 is to convert and provide the uncompensated analog output voltage from the piezoresistive pressure sensor to a 24-bit digital value for the temperature of the sensor. It can measure pressure in a range from 300mbar up to 1.2bar with an accuracy of ±2mbar over a wide operating temperature range at the industry's lowest power.
As mentioned before, the MS5637-02BA03 has integrated ultra-low-power 24-bit ΔΣ ADC with internal factory-calibrated coefficients, which alongside precise pressure value, also provides temperature value. A high-resolution temperature output allows the implementation of an altimeter/thermometer function without any additional sensor, with an altitude resolution at sea level of 13cm of air.
The Barometer 5 Click Board™ communicates with MCU using the standard I2C 2-Wire interface to read data and configure settings, supporting Standard Mode operation with a clock frequency of 100kHz and Fast Mode up to 400kHz. Besides, it also offers different operation modes allowing the user to optimize for conversion speed and current consumption.
Suppose the user decides not to use our compliant library but to do software development independently. In that case, it is recommended to compensate for the non-linearity over the temperature to obtain the best accuracy over the temperature range, particularly at low temperatures. This can be achieved by correcting the calculated temperature, offset, and sensitivity by a second-order correction factor.
The Barometer 5 Click Board™ can be operated only with a 3.3V logic voltage level. The board must perform appropriate logic voltage level conversion before using MCUs with different logic levels. However, the Click board™ comes equipped with a library containing functions and an example code that can be used, as a reference, for further development.
SPECIFICATIONS
| Type | Pressure |
| Applications | The Barometer 5 Click Board™ be used for various pressure-based applications, especially when low power consumption is required |
| On-board modules | MS5637-02BA03 - high accuracy low voltage barometric and temperature sensor from TE Connectivity Measurement Specialties, to measure air pressure in a specific environment |
| Key Features | Low power consumption, high resolution and precision, embedded temperature sensor, temperature stability, accuracy of ±2mbar over a wide operating temperature range, also measure altitude of 13cm, and more |
| Interface | I2C |
| Compatibility | mikroBUS |
| Click board size | S (28.6 x 25.4 mm) |
| Input Voltage | 3.3V |
PINOUT DIAGRAM
This table shows how the pinout for the Barometer 5 Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| NC | 1 | AN | PWM | 16 | NC | ||
| NC | 2 | RST | INT | 15 | NC | ||
| NC | 3 | CS | RX | 14 | NC | ||
| NC | 4 | SCK | TX | 13 | NC | ||
| NC | 5 | MISO | SCL | 12 | SCL | I2C Clock | |
| NC | 6 | MOSI | SDA | 11 | SDA | I2C Data | |
| Power Supply | 3.3V | 7 | 3.3V | 5V | 10 | NC | |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
ONBOARD SETTINGS AND INDICATORS
| Label | Name | Default | Description |
|---|---|---|---|
| LD1 | PWR | - | Power LED Indicator |
BAROMETER 5 CLICK ELECTRICAL SPECIFICATIONS
| Description | Min | Typ | Max | Unit |
|---|---|---|---|---|
| Supply Voltage | 3.3 | - | 5 | V |
| Operating Pressure Range | 300 | - | 1200 | mbar |
| Accuracy | - | ±2 | - | mbar |
| ADC Resolution | - | 24 | - | bit |
| Operating Temperature Range | -40 | +25 | +85 | °C |
Software Support
We provide a library for the Barometer 5 Click Board™ as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
The package can be downloaded/installed directly from NECTO Studio The package Manager (recommended), downloaded from our LibStock™ or found on Mikroe Github account.
Library Description
This library contains API for the Barometer 5 Click Board™ driver.
Key functions
-
barometer5_get_dataBarometer 5 get data function. -
barometer5_get_pressureBarometer 5 get pressure data function. -
barometer5_get_temperatureBarometer 5 get temperature data function.
Example Description
This library contains API for the Barometer 5 Click Board™ driver. The demo application reads and calculate temperature and pressure data.
void application_task ( void )
{
static float temperature;
static float pressure;
if ( barometer5_get_data( &barometer5, &temperature, &pressure ) == BAROMETER5_OK )
{
log_printf( &logger, " Pressure : %.2f mbar rn", pressure );
log_printf( &logger, " Temperature : %.2f C rn", temperature );
log_printf( &logger, "---------------------------rn" );
}
Delay_ms( 1000 );
}
The full application code, and ready to use projects can be installed directly from NECTO Studio The package Manager (recommended), downloaded from our LibStock™ or found on Mikroe Github account.
Other Mikroe Libraries used in the example:
- MikroSDK.Board
- MikroSDK.Log
- Click.Barometer5
Additional Notes and Information
Depending on the development board you are using, you may need a USB UART Click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MikroElektronika compilers.
MIKROSDK
The Barometer 5 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Barometer 5 Click Board
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.