Mikroelektronika d.o.o.
AudioAMP 8 Click-Platine
AudioAMP 8 Click-Platine
Verfügbarkeit für Abholungen konnte nicht geladen werden
Key Features:
- Proprietäre mehrstufige Schalttechnologie, hohe Energieeffizienz, hohe Audioleistung, geringer Stromverbrauch, flexible Ausgangsstufenkonfiguration, Schutzfunktion und mehr
- Basierend auf dem MA12070 – dem hocheffizienten Audio-Leistungsverstärker von Infineon Technologies
- Kann für verschiedene Arten von Audiogeräten für den Verbraucherbereich verwendet werden
- microBUS: I2C-Schnittstelle
Das AudioAmp 8 Click Board™ ist eine kompakte Zusatzplatine, die Eingangs-Audiosignale mit gewünschter Lautstärke und Leistungspegeln an klangerzeugenden Ausgangselementen wiedergibt. Diese Platine verfügt über den MA12070, einen hocheffizienten Stereo-Audio-Leistungsverstärker von Infineon Technologies. Dieser I2C-konfigurierbare Audioverstärker basiert auf einer proprietären mehrstufigen Schalttechnologie, die einen geringen Leistungsverlust während des Betriebs ermöglicht. Er unterstützt einen Versorgungsspannungsbereich von 4 bis 26 V und kann daher in vielen Anwendungen eingesetzt werden. Außerdem ist er mit Schutzfunktionen ausgestattet, die einen zuverlässigen Betrieb ermöglichen. Dieses Click Board™ ist für verschiedene Arten von Anwendungen mit Audiogeräten für Verbraucher geeignet.
Das AudioAmp 8 Click Board™ wird von einer mikroSDK-kompatiblen Bibliothek unterstützt, einschließlich Funktionen, die die Softwareentwicklung vereinfachen. Dieses Click Board™ ist ein gründlich getestetes Produkt und kann auf einem System verwendet werden, das mit der mikroBUS™-Buchse ausgestattet ist.
How Does The AudioAmp 8 Click Board™ Work?
The AudioAmp 8 Click Board™ is based on the the MA12070, a super-efficient audio power amplifier based on proprietary multi-level switching technology that enables low power loss during operation from Infineon Technologies. The MA12070 is equipped with an intelligent power management algorithm that applies automatic power mode selection during audio playback. In this state, the amplifier will seamlessly transition between three different power modes depending on the audio level to achieve optimal power loss, audio performance, and EMI. Alternatively, it is also possible to manually select the desired power mode for the MA12070 via a serial interface.
The MA12070 communicates with MCU using the standard I2C 2-Wire interface that supports Standard (100 kHz) and Fast (400 kHz) modes of operation. It has a 7-bit slave address with the first five MSBs fixed to 01000. The address pins are programmed by the user and determine the value of the last two LSBs of the slave address, which can be selected by positioning onboard SMD jumpers labelled as ADDR SEL to an appropriate position marked as 0 or 1.
The AudioAmp 8 Click Board™ supports an external power supply for the motor, which can be connected to the input terminal labelled as VIN and should be within the range of 6V to 26V, while the input audio can be brought to the input jack labelled as AUDIO IN and after specific processing reproduced on the speakers of the desired channel SPK OUT.
The MA12070 is highly flexible regarding the configuration of the four power amplifier channels. It can be set to four different output configurations by setting the configuration pins MS0 and MS1, routed to the INT and PWM pins of the mikroBUS™ socket. In addition to these pins, this Click board™ uses a few more pins of the mikroBUS™ socket. The Enable pin, labelled as EN and routed to the CS pin of the mikroBUS™ socket, optimizes power consumption used for power ON/OFF purposes, while the MUT pin routed to the RST pin allows users to mute audio on connected speakers.
Besides, it is possible to detect operational irregularities, such as overcurrent and short-circuit detection. An indication of such a condition is performed using the red LED indicator labelled as ERROR, alongside an audio clipping indication accomplished using the blue LED indicator labelled as CLIP which indicates when audio output is close to clipping.
The AudioAmp 8 Click Board™ can be operated only with a 5V logic voltage level. The board must perform appropriate logic voltage level conversion before using MCUs with different logic levels. However, the Click board™ comes equipped with a library containing functions and an example code that can be used, as a reference, for further development.
SPECIFICATIONS
| Type | Amplifier |
| Applications | Can be used for various types of consumer audio equipment applications |
| On-board modules | MA12070 - super-efficient audio power amplifier from Infineon Technologies |
| Key Features | Proprietary multi-level switching technology, high power efficiency, high audio performance, low power consumption, flexible output stage configuration, protection feature, and more |
| Interface | I2C |
| Compatibility | mikroBUS |
| Click board size | L (57.15 x 25.4 mm) |
| Input Voltage | 5V,External |
PINOUT DIAGRAM
This table shows how the pinout of the AudioAmp 8 Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| NC | 1 | AN | PWM | 16 | MS0 | Output Stage Config. 0 | |
| Audio Mute | MUT | 2 | RST | INT | 15 | MS1 | Output Stage Config. 1 |
| Device Enable | EN | 3 | CS | RX | 14 | NC | |
| NC | 4 | SCK | TX | 13 | NC | ||
| NC | 5 | MISO | SCL | 12 | SCL | I2C Clock | |
| NC | 6 | MOSI | SDA | 11 | SDA | I2C Data | |
| NC | 7 | 3.3V | 5V | 10 | 5V | Power Supply | |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
ONBOARD SETTINGS AND INDICATORS
| Label | Name | Default | Description |
|---|---|---|---|
| LD1 | PWR | - | Power LED Indicator |
| LD2 | ERROR | - | Error LED Indicator |
| LD3 | CLIP | - | Audio Clipping LED Indicator |
| JP1-JP2 | ADDR SEL | Left | I2C Address Selection 0/1: Left position 0, Right position 1 |
AUDIOAMP 8 CLICK ELECTRICAL SPECIFICATIONS
| Description | Min | Typ | Max | Unit |
|---|---|---|---|---|
| Supply Voltage | - | 5 | - | V |
| External Power Supply Voltage VIN | 4 | - | 26 | V |
| Output Power (per channel) | - | 80 | - | W |
| Operating Temperature Range | 0 | +25 | +85 | °C |
Software Support
We provide a library for the AudioAmp 8 Click Board™ as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Library Description
This library contains API for the AudioAmp 8 Click Board™ driver.
Key Functions
audioamp8_cfg_setup- Config Object Initialization function.audioamp8_init- Initialization function.audioamp8_default_cfg- Click Default Configuration function.
Example Description
This library contains API for the AudioAmp 8 Click Board™ driver. The library initializes and defines the I2C bus drivers to write and read data from registers.
void application_init ( void )
{
log_cfg_t log_cfg; /**< Logger config object. */
audioamp8_cfg_t audioamp8_cfg; /**< Click config object. */
// Logger initialization.
LOG_MAP_USB_UART( log_cfg );
log_cfg.level = LOG_LEVEL_DEBUG;
log_cfg.baud = 115200;
log_init( &logger, &log_cfg );
log_info( &logger, " Application Init " );
// Click initialization.
audioamp8_cfg_setup( &audioamp8_cfg );
AUDIOAMP8_MAP_MIKROBUS( audioamp8_cfg, MIKROBUS_1 );
err_t init_flag = audioamp8_init( &audioamp8, &audioamp8_cfg );
if ( I2C_MASTER_ERROR == init_flag )
{
log_error( &logger, " Application Init Error. " );
log_info( &logger, " Please, run program again... " );
for ( ; ; );
}
audioamp8_default_cfg ( &audioamp8 );
log_info( &logger, " Application Task " );
audioamp8_btl_config( &audioamp8 );
Delay_ms( 100 );
pwr_mode.manual_pm = AUDIOAMP8_SET_MANUAL_PWR_MODE;
pwr_mode.pm_man = AUDIOAMP8_PM_MAN_3;
pwr_mode.mthr_1to2 = AUDIOAMP8_SET_MTHR_1TO2_DEFAULT;
pwr_mode.mthr_2to1 = AUDIOAMP8_SET_MTHR_2TO1_DEFAULT;
pwr_mode.mthr_2to3 = AUDIOAMP8_SET_MTHR_2TO3_DEFAULT;
pwr_mode.mthr_3to2 = AUDIOAMP8_SET_MTHR_3TO2_DEFAULT;
audioamp8_set_config_power_mode( &audioamp8, pwr_mode );
Delay_ms( 100 );
pm_profile.pm_profile = AUDIOAMP8_PM_PROFILE_3;
pm_profile.pm3_man_sh = AUDIOAMP8_SCHEME_C;
audioamp8_set_config_power_mode_profile( &audioamp8, pm_profile );
Delay_ms( 100 );
audioamp8_set_mute( &audioamp8, AUDIOAMP8_SET_DISABLE );
log_printf( &logger, "-------------------------rn" );
Delay_ms( 1000 );
}
The full application code, and ready to use projects can be installed directly from NECTO Studio The Package Manager (recommended), downloaded from our LibStock™ or found on MikroE Github account.
Other mikroE Libraries used in the example:
- MikroSDK.Board
- MikroSDK.Log
- Click.AudioAmp8
Additional Notes and Information
Depending on the development board you are using, you may need a USB UART Click Board™, USB UART 2 Click Board™ or RS232 Click Board™ to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.
MIKROSDK
The AudioAmp 8 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
AudioAMP 8 Click-Platine
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.