Mikroelektronika d.o.o.
Air Flow Click-Platine
Air Flow Click-Platine
Verfügbarkeit für Abholungen konnte nicht geladen werden
Das Air Flow Click Board™ ist eine kompakte Zusatzplatine, die einen strömungsbasierten 2-in-1-Differenzdrucksensor enthält. Diese Platine verfügt über den Mikroströmungs-Differenzdrucksensor LHDULTRAM012UB3, LHD ULTRA-Serie von First Sensor (Teil von TE Connectivity). Dieser Drucksensor basiert auf der thermischen Durchflussmessung von Gas durch zwei Mikroströmungskanäle, die in den Silizium-Sensorchip integriert sind, um den Dynamikbereich des Sensors von 0 bis 1250 Pa effektiv zu maximieren. Eine integrierte MCU mit einem genauen 24-Bit-ADC bietet Signalverarbeitung, einschließlich Reaktion der beiden Sensorelemente, Linearisierung, barometrische Kompensation und Temperaturkorrektur.
Das Air Flow Click Board™ ist ideal für die Luftstromüberwachung und medizinische Anwendungen, die hohe Präzision, einen erweiterten Messbereich und den Komfort eines einzelnen Geräts erfordern.
How Does The Air Flow Click Board™ Work?
The Air Flow Click Board™ as its foundation uses the LHDULTRAM012UB3, an LHD ULTRA series flow-based 2-in-1 differential pressure sensor from TE Connectivity Measurement Specialties. It consists of two combined calorimetric micro-flow channels and two sensor elements on a single chip. The first sensing element ensures precise measurement of low differential pressures with high resolution, and the second sensing element is optimized for pressures in the upper measuring range. A fast-response 24-bit onboard controller delivers precise measurement results across the entire dynamic measuring range from 0 to 1250Pa.
The specific concept of the LHDULTRAM012UB3 ensures continuous operation that is highly reliable and economically efficient in addition to the outstanding long-term stability, precision with patented real-time offset compensation, and linearization techniques. The LHD ULTRA's high flow impedance ensures product-specific insensitivity to dust/moisture as well as minimal flow leakage.
The Air Flow Click Board™ provides the possibility of using both I2C and SPI interfaces with a maximum frequency of 100kHz for I2C and 1MHz for SPI communication. The selection can be made by positioning SMD jumpers labelled as COMM SEL to an appropriate position. Note that all the jumpers' positions must be on the same side, or else the Click board™ may become unresponsive.
While the I2C interface is selected, the LHDULTRAM012UB3 allows the choice of the least significant bit (LSB) of its I2C slave address using the SMD jumpers labelled as A0 and A1 to an appropriate position marked as 0 and 1. Also, an additional ready signal, routed on the INT pin of the mikroBUS™ socket, is added, indicating that new data is ready for the host.
The Air Flow Click Board™ can be operated only with a 3.3V logic voltage level. The board must perform appropriate logic voltage level conversion before use with MCUs with different logic levels. However, the Click board™ comes equipped with a library containing functions and an example code that can be used, as a reference, for further development.
SPECIFICATIONS
| Type | Pressure |
| Applications | Can be used for industrial and medical applications that demand high precision, extended measurement range, and the convenience of a single device |
| On-board modules | LHDULTRAM012UB3 - LHD ULTRA series flow-based 2-in-1 differential pressure sensor from TE Connectivity Measurement Specialties |
| Key Features | Low power consumption, ultra-low pressure ranges, based on thermal microflow measurement, high flow impedance, outstanding long-term stability, on-chip temperature sensor and barometer, SPI/I2C interfaces, and more |
| Interface | I2C,SPI |
| Compatibility | mikroBUS |
| Click board size | L (57.15 x 25.4 mm) |
| Input Voltage | 3.3V |
PINOUT DIAGRAM
This table shows how the pinout of the Air Flow Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| NC | 1 | AN | PWM | 16 | NC | ||
| NC | 2 | RST | INT | 15 | RDY | Data Ready | |
| SPI Chip Select | CS | 3 | CS | RX | 14 | NC | |
| SPI Clock | SCK | 4 | SCK | TX | 13 | NC | |
| SPI Data OUT | SDO | 5 | MISO | SCL | 12 | SCL | I2C Clock |
| SPI Data IN | SDI | 6 | MOSI | SDA | 11 | SDA | I2C Data |
| Power Supply | 3.3V | 7 | 3.3V | 5V | 10 | NC | |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
ONBOARD SETTINGS AND INDICATORS
| Label | Name | Default | Description |
|---|---|---|---|
| LD1 | PWR | - | Power LED Indicator |
| JP1/JP2/JP5 | COMM SEL | Left | Communication Interface Selection SPI/I2C: Left position SPI, Right position I2C |
| JP3-JP4 | COMM SEL | Left | Multifunctional Selection SPI lines/I2C Address Selection: Left position 0, Right position 1, Upper position SPI lines |
AIRFLOW CLICK ELECTRICAL SPECIFICATIONS
| Description | Min | Typ | Max | Unit |
|---|---|---|---|---|
| Supply Voltage | - | 3.3 | - | V |
| Pressure Measurement Range | 0 | - | 12.5 | mbar |
| Accuracy | - | 1.5 | - | % |
| Operating Temperature Range | -40 | +25 | +85 | °C |
Software Support
We provide a library for the Air Flow Click Board™ as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
The package can be downloaded/installed directly from NECTO Studio Package Manager (recommended), downloaded from our LibStock™ or found on Mikroe Github account.
Library Description
This library contains an API for the Air Flow Click Board™ driver.
Key Functions
airflow_cfg_setup- Config Object Initialization function.airflow_init- Initialization function.airflow_default_cfg- Click the Default Configuration function.
Example Description
This example showcases the ability of the device to read differential pressure, atmospheric pressure and ambient temperature.
The demo application is composed of two sections :
void application_task ( void )
{
float pressure_data, temperature_data;
airflow_get_differential_pressure( &airflow, &pressure_data );
log_printf( &logger, "Differential pressure[Pa]: %.2frn", pressure_data );
airflow_get_atmospheric_pressure( &airflow, &pressure_data, &temperature_data );
log_printf( &logger, "Atmospheric pressure[mBar]: %.2frnTemperature[degC]: %.2frn", pressure_data, temperature_data );
log_printf( &logger, "***********************************************************rn" );
Delay_ms( 500 );
}
The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe Github account.
Other Mikroe Libraries used in the example:
- MikroSDK.Board
- MikroSDK.Log
- Click.AirFlow
Additional Notes and Information
Depending on the development board you are using, you may need a USB UART click, USB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.
MIKROSDK
The Air Flow Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Air Flow Click-Platine
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.