Mikroelektronika d.o.o.
7-Segment-RGB-Click-Platine
7-Segment-RGB-Click-Platine
Verfügbarkeit für Abholungen konnte nicht geladen werden
Der 7-Seg RGB Click Board™ verfügt über eine vollfarbige 7-Segment-Einzelziffernanzeige. Das Click ist für den Betrieb mit einer 3,3-V- oder 5-V-Stromversorgung ausgelegt. Es kommuniziert mit dem Zielmikrocontroller über den CS- und PWM-Pin auf der mikroBUS™-Leitung.
Das 7-Segment RGB Click Board™ kann in einer Kette verbunden werden, um eine größere Anzahl von Zeichen anzuzeigen. Im Gegensatz zu herkömmlichen 7-Segment-Anzeigen können Sie mehrere Farben auf dem Display verwenden.
Display Features
Each segment has R, G, B LEDs that can be adjusted in 255 steps and therefore 16,581,375 colour combinations are available for each segment of the digit on the display.
Also, the ability to control the brightness of all the LED's is driven at 255 steps. It should be noted that brightness values above 80 should rarely be used.
Specifications
| Type | 7-segment, LED Segment |
| Applications | Displaying digits and letters on a seven-segment in full colour |
| On-board modules | RGBdigit full-colour single 7 Segment digit display |
| Key Features | Multi-coloured display |
| Interface | PWM |
| Compatibility | mikroBUS |
| Click board size | L (57.15 x 25.4 mm) |
| Input Voltage | 3.3V or 5V |
Pinout Diagram
This table shows how the pinout on the 7-SEG RGB Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| NC | 1 | AN | PWM | 16 | PWM | Data input | |
| NC | 2 | RST | INT | 15 | NC | ||
| Write enable (active low) | CS | 3 | CS | TX | 14 | NC | |
| NC | 4 | SCK | RX | 13 | NC | ||
| NC | 5 | MISO | SCL | 12 | NC | ||
| NC | 6 | MOSI | SDA | 11 | NC | ||
| Power supply | +3.3V | 7 | 3.3V | 5V | 10 | +5V | Power supply |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
Jumpers and settings
| Designator | Name | Default Position | Default Option | Description |
|---|---|---|---|---|
| JP1 | Logic level | Left | 3.3V | Data in level Voltage Selection 3V3/5V, left position 3V3, right position 5V |
Software Support
Code examples for the 7-SEG RGB Click Board™, written for MikroElektronika hardware and compilers are available on Libstock.
Code Snippet
The following code snippet writes the numbers 1, 2 and 3 in green, red and blue colours on the 7-SEG RGB Click Board™.
01 #define ONE 0x06
02 #define TWO 0x5B
03 #define THREE 0x4F
04 sbit CS_BIT at GPIOD_ODR.B13;
05 sbit RGB_CONTROL_BIT at GPIOA_ODR.B0;
06 void systemInit()
07 {
08 GPIO_Digital_Output( &GPIOD_BASE, _GPIO_PINMASK_13 );
09 GPIO_Digital_Output( &GPIOA_BASE, _GPIO_PINMASK_0 );
10 }
11 void RGB_7_SEG_Init()
12 {
13 RGB_CONTROL_BIT = 0;
14 CS_BIT = 0;
15 }
16 void RGB_7_SEG_Task()
17 {
18 setSevenSegment(ONE,40,0,0);
19 Delay_ms(1000);
20 setSevenSegment(TWO,0,40,0);
21 Delay_ms(1000);
22 setSevenSegment(THREE,0,0,40);
23 Delay_ms(1000);
24 }
25 void main()
26 {
27 systemInit();
28 RGB_7_SEG_Init();
29 while( 1 )
30 {
31 RGB_7_SEG_Task();
32 }
7-Segment-RGB-Click-Platine
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.