
Key Features
Overview
The J-Trace Isolator provides 1 kV DC basic electrical isolation between a J-Trace PRO and a target with the standard 0.05" 19-pin Cortex-M connector, while passing JTAG, SWD and ETM trace. It works with 1.2V to 5V targets, at JTAG and SWD speeds up to 4 MHz and trace clocks up to 75 MHz. It is designed for J-Trace V2 or later.
The SEGGER J-Trace Isolator (part number 8.07.10) provides 1 kV DC basic electrical isolation between a J-Trace PRO and a target with the standard 0.05" 19-pin Cortex-M connector, while passing JTAG, SWD and ETM trace. It works with 1.2V to 5V targets, at JTAG and SWD speeds up to 4 MHz and trace clocks up to 75 MHz. It is for trace and debug work where the probe and the target must be kept electrically separate.
Isolated ETM Trace on the 19-Pin Cortex-M Connector
Both sides of the isolator use a 0.05" 19-pin Cortex-M male connector: EMULATOR connects to the J-Trace cable and TARGET to the target cable. ETM trace pins are fully supported, with TRACECLK and TRACEDATA0 to TRACEDATA3 carried through high-speed digital isolators. SEGGER rates the trace clock at up to 75 MHz, the limit of the isolator IC, and reports up to 120 MHz in one example setup at room temperature with adjusted sampling delays in the J-Trace PRO.
Powered from the J-Trace PRO
The probe powers the isolator logic through pins 11 and 13, so the J-Trace PRO must supply 5V there; SEGGER notes that you may need to run "power on perm" once in J-Link Commander. The target side draws only a few microamps (under 25 µA). Three LEDs show emulator power, target power and target RESET.
What's Included
- J-Trace Isolator
- 20-pin target ribbon cable
Specifications
| Isolation | 1 kV DC, basic isolation |
|---|---|
| Connectors | EMULATOR and TARGET, each 0.05" 19-pin Cortex-M male |
| Target voltage | 1.2V to 5V |
| JTAG frequency | Up to 4 MHz |
| SWD frequency | Up to 4 MHz |
| Trace clock | Up to 75 MHz |
| Trace signals | TRACECLK, TRACEDATA0 to TRACEDATA3 |
| Power | From the probe, 5V on pins 11 and 13; under 25 µA from target |
| Indicators | Emulator power (green), target power (green), target RESET (red) |
| Designed for | J-Trace V2 or later |
Limitations
- Basic isolation only. SEGGER requires double or reinforced isolation to protect people from hazardous voltages, so do not rely on the isolator alone in that case.
- JTAG and SWD are limited to 4 MHz, and trace clocks above 75 MHz are beyond the isolator IC's specification.
- VTref (pin 1) must have no series resistor, and pin 9 should be left open on the target.
- Other ARM emulators with the same pinout need 5V on pin 19 of the emulator connector; SEGGER states this is at your own risk.
J-Trace Isolator Compared with the J-Link Isolators
| Isolator | Connectors | Interfaces | Trace | Price ex VAT |
|---|---|---|---|---|
| J-Trace Isolator (this product) | 0.05" 19-pin Cortex-M | JTAG, SWD, up to 4 MHz | ETM, up to 75 MHz trace clock | €400,95 |
| J-Link JTAG Isolator | 20-pin 0.1" JTAG | JTAG, up to 4 MHz | No | €282,95 |
| SWD Isolator | 20-pin 0.1" SWD | SWD and SWO, up to 4 MHz | No | €300,95 |
Order the J-Trace Isolator for €400,95 ex VAT, or ask us for a formal quotation. SEGGER lists it as suitable for the J-Trace PRO, J-Trace PRO Cortex-A/R/M, J-Trace PRO Cortex-M and J-Trace PRO RISC-V. See the full SEGGER debug probes collection.
Last reviewed 16/11/2026.
| General | |
|---|---|
| Isolation | 1 kV DC, basic isolation |
| Indicators | Emulator power (green), target power (green), target RESET (red) |
| Designed for | J-Trace V2 or later |
| Host and Target Interface | |
| Connectors | EMULATOR and TARGET, each 0.05" 19-pin Cortex-M male |
| Target voltage | 1.2V to 5V |
| Performance | |
| JTAG frequency | Up to 4 MHz |
| SWD frequency | Up to 4 MHz |
| Trace clock | Up to 75 MHz |
| Trace signals | TRACECLK, TRACEDATA0 to TRACEDATA3 |
| Power | |
| Power | From the probe, 5V on pins 11 and 13; under 25 µA from target |
| Ordering information | |
| Part number (SKU) | 8.07.10 |
| Manufacturer | SEGGER Microcontroller GmbH |
| EAN | 5055383619962 |
| Warranty | 12 Monate |
| Shipping weight | 0.05 kg |
- 1 ×J-Trace Isolator
- 1 ×20-pin 0.05" target ribbon cable
Questions and Answers
-
Does the Target Need to Power the J-Trace Isolator?
No. The J-Trace PRO powers the isolator logic with 5V on pins 11 and 13. Only a few microamps, under 25 µA, are drawn from the target.
-
How Fast Can Trace Run Through the Isolator?
SEGGER specifies a trace clock up to 75 MHz, set by the digital isolator IC. It reports up to 120 MHz in one tested setup at room temperature with adjusted J-Trace PRO sampling delays, but that is outside the specification.
No questions match your search.