Mikroelektronika d.o.o.
ECG 6 Click-Platine
ECG 6 Click-Platine
Verfügbarkeit für Abholungen konnte nicht geladen werden
Overview
Das ECG 6 Click Board™ ist eine Komplettlösung für die Entwicklung von EKG- und Herzfrequenz-Anwendungen. Es verfügt über den MAX86150, einen reflektierenden Herzfrequenzmonitor und ein medizinisches Pulsoximeter von Maxim Integrated. Das Click Board™ enthält ein integriertes Sensormodul für Elektrokardiogramm, Pulsoximeter und Herzfrequenzmonitor. Das ECG 6 Click kann für die Anwendung in Fitnessassistenten, tragbaren Geräten, Smartphones und Tablets verwendet werden.
Das ECG 6 Click wird von einer mikroSDK-kompatiblen Bibliothek unterstützt, die Funktionen enthält, die die Softwareentwicklung vereinfachen. Dieses Click Board™ wird als vollständig getestetes Produkt geliefert und ist bereit für den Einsatz auf einem System, das mit der mikroBUS™-Buchse ausgestattet ist.
Hinweis: ECG 6 ist ein Entwicklungs- und Prototyping-Tool. Es ist nicht für die medizinische Behandlung von Patienten vorgesehen und sollte nicht zur Diagnose oder Behandlung von Erkrankungen verwendet werden.
How Does The ECG 6 Click Board™ Work?
The ECG 6 Click Board™ is based on the MAX86150, is a complete electrocardiogram (ECG) from Maxim Integrated. It is designed for mobile health. The Click board™ has many features to provide health measurements: electrocardiogram, pulse oximetry, and heart rate. All these features allow ECG 6 click to be used in a range of health-related ECG, SpO2 subsystem and HR applications including fitness and activity heart rate monitors, portable ECG, wearable and remote health monitors, and similar.
The MAX86150 contain integrated the SpO2 subsystem. The SpO2 subsystem is peripheral capillary oxygen saturation. It is measured by a device called a pulse oximeter. A clip is placed on the finger or foot of the patient and light is sent through the finger and measured on the other side. The MAX86150 integrates red and infrared LED drivers to modulate LED pulses for SpO2 and HR measurements. The LED current can be programmed from 0mA to 100mA with proper VLED supply voltage. The LED pulse width can be programmed from 50μs to 400μs to optimize accuracy of results and power consumption based on use cases.
The ECG 6 Click Board™ allows several types of electrodes to be used. It supports both stainless-steel and silver-chloride electrode types. The electrodes are used to perform differential measurement of the voltage generated by the heart. Therefore, the heart can be monitored from a single plane only - the coronal plane. However, this is quite enough for the fitness, heart rate monitoring and similar applications.
The extensive interrupt engine can be used to trigger the host MCU from various sources, including interrupt events due to lead detection, R-R detection, fast-recovery event, FIFO buffer states, and many more. These interrupt sources can be utilized to trigger a state change on the interrupt pin (INT) of the MAX86150 IC. This pin is active-low.
The voltage level of the logic section can be selected via VCC SEL jumper, between 3.3V and 5V. This allows for both 3.3V and 5V capable MCUs to use the SPI communication lines properly.
SPECIFICATIONS
| Type | Biometrics,ECG |
| Applications | Medical health: Fitness Assistant Devices, Wearable Devices, Smartphones, Tablet, |
| On-board modules | MAX86150 electrocardiogram from Maxim Integrated. |
| Key Features | Reflective Heart Rate Monitor, Medical-Grade Pulse Oximeter, |
| Interface | I2C |
| Compatibility | mikroBUS |
| Click board size | M (42.9 x 25.4 mm) |
| Input Voltage | 3.3V or 5V |
PINOUT DIAGRAM
This table shows how the pinout on the ECG 6 Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| NC | 1 | AN | PWM | 16 | NC | ||
| NC | 2 | RST | INT | 15 | INT | Interrupt OUT | |
| NC | 3 | CS | RX | 14 | NC | ||
| NC | 4 | SCK | TX | 13 | NC | ||
| NC | 5 | MISO | SCL | 12 | SCL | I2C Clock | |
| NC | 6 | MOSI | SDA | 11 | SDA | I2C Data | |
| Power Supply | 3.3V | 7 | 3.3V | 5V | 10 | 5V | Power supply |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
ONBOARD SETTINGS AND INDICATORS
| Label | Name | Default | Description |
|---|---|---|---|
| JP1 | VCC SEL | Left | Power supply voltage selection: left position 3.3V, right position 5V |
| LD1 | PWR | - | Power LED indicator |
| CN1 | 3.5mm JACK | - | 3.5mm electrodes connector |
Software Support
We provide a library for the ECG 6 Click Board™ on our LibStock page, as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Library Description
The library provides the user with measurements from ECG sensors and PPG sensors. The user has full control of module settings and reads all registers via I2C communication.
Key Functions
void ecg6_get_sample_data( ecg6_element_t *element, uint8_t num_sample )- Get one sample from FIFOuint8_t ecg6_ppg_default_config ( )- Default configuration for PPG sensoruint8_t ecg6_ecg_default_config ( )- Default configuration for ECG sensor
Example Description
The application is composed of three sections :
- System Initialization - Initialize I2C module and all necessary pins
- Application Initialization - Checking communication accuracy and running default configuration for measurement
- Application Task - Measures an ECG signal or PPG sensor and draws a graph on a SerialPlot
void application_task ( )
{
ecg6_element_t sample;
ecg6_get_sample_data( &sample, 0x00 );
if ( DEMO_EXAMPLE == ECG_EXAMPLE )
{
plot_ecg_data( sample.element_1 );
}
else
{
plot_ppg_data( sample.element_1, sample.element_2 );
}
}
Additional Functions :
- plot_ecg_data ( ) - Sends ECG sensor data to SerialPlot
- plot_ppg_data ( ) - Sends PPG sensor data to SerialPlot
Note: When using ECG measurement - PPG measurement must be switched off ... Drawing speeds vary for PPG and ECG sensor.
The full application code, and ready to use projects can be found on our LibStock page.
Other mikroE Libraries used in the example:
- I2C Library
- Conversions Library
- String Library
- UART Library
Additional Notes and Information
Depending on the development board you are using, you may need a USB UART click, USB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.
MIKROSDK
The ECG 6 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Software Support
We provide a library for the ECG 6 Click Board™ on our LibStock page, as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Library Description
The library provides the user with measurements from ECG sensors and PPG sensors. The user has full control of module settings and reads all registers via I2C communication.
Key Functions
void ecg6_get_sample_data( ecg6_element_t *element, uint8_t num_sample )- Get one sample from FIFOuint8_t ecg6_ppg_default_config ( )- Default configuration for PPG sensoruint8_t ecg6_ecg_default_config ( )- Default configuration for ECG sensor
Example Description
The application is composed of three sections :
- System Initialization - Initialize I2C module and all necessary pins
- Application Initialization - Checking communication accuracy and running default configuration for measurement
- Application Task - Measures an ECG signal or PPG sensor and draws a graph on a SerialPlot
void application_task ( )
{
ecg6_element_t sample;
ecg6_get_sample_data( &sample, 0x00 );
if ( DEMO_EXAMPLE == ECG_EXAMPLE )
{
plot_ecg_data( sample.element_1 );
}
else
{
plot_ppg_data( sample.element_1, sample.element_2 );
}
}
Additional Functions :
- plot_ecg_data ( ) - Sends ECG sensor data to SerialPlot
- plot_ppg_data ( ) - Sends PPG sensor data to SerialPlot
Note: When using ECG measurement - PPG measurement must be switched off ... Drawing speeds vary for PPG and ECG sensor.
The full application code, and ready to use projects can be found on our LibStock page.
Other mikroE Libraries used in the example:
- I2C Library
- Conversions Library
- String Library
- UART Library
Additional Notes and Information
Depending on the development board you are using, you may need a USB UART click, USB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.
MIKROSDK
The ECG 6 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.