
Caractéristiques principales
Overview
The STM32H7 Trace Reference Board is an ETM trace target built on the ST STM32H743, an ARM Cortex-M7 microcontroller running at up to 400 MHz with 4-bit trace and a trace port clock of 266 MHz. It supports JTAG, SWD and SWO and takes its power from the SEGGER J-Trace PRO through the trace header. Example projects for streaming trace and the on-chip trace buffer are on SEGGER's Knowledge Base.
The SEGGER STM32H7 Trace Reference Board (part number 6.68.20) is an ETM trace target built on the ST STM32H743, an ARM Cortex-M7 microcontroller with a maximum CPU clock of 400 MHz, 4-bit trace reaching a maximum trace bandwidth of 1064 Mbps and a trace port clock of 266 MHz. It supports JTAG, SWD and SWO, takes its power from SEGGER J-Trace PRO through the trace header, and has example projects on SEGGER's Knowledge Base for both streaming trace and the on-chip trace buffer. It serves firmware engineers proving a Cortex-M7 trace setup and hardware engineers who need a reference for trace signal quality on a custom board.
Cortex-M7 Streaming Trace Reference for J-Trace PRO
SEGGER states the prime purpose of the board as quickly setting up a reference project for instruction tracing, live code coverage and profiling. All trace signals on the board are optimised for signal quality, so the board gives a known-good result to compare against when trace on your own STM32H7 design is unreliable.
Trace Header, Test Points and Target Power
The external debug header carries the trace pins. SEGGER's 19-pin JTAG/SWD and trace connector assigns VTref, SWDIO/TMS, SWCLK/TCK, SWO/TDO, TDI, nRESET, TRACECLK and TRACEDATA[0] to [3]; pins 3, 5, 15, 17 and 19 are GND and pin 9 is left open. J-Trace PRO can supply 5V to the target on pins 11 and 13, so the board needs no separate power cable: run power on perm in J-Link Commander, then connect the board, and the green Target power LED on the probe lights. All trace signals are also brought out as test points for oscilloscope measurements, and three LEDs are free for use in trace demo applications.
Streaming Trace and Trace Buffer Example Projects
SEGGER's STM32H7 Knowledge Base article names this board as its tested hardware and provides two tutorial projects. ST_STM32H7_Trace_Tutorial_Project demonstrates streaming trace with the core at 64 MHz and the trace clock at 32 MHz. ST_STM32H7_TraceBuffer_Tutorial_Project uses the on-chip trace buffer instead and is not intended for streaming trace. Both are prebuilt and run in Ozone without rebuilding; SEGGER Embedded Studio is used to rebuild them.
For streaming trace SEGGER lists J-Link software V6.60d or later, Ozone V3.10b or later and J-Trace PRO for Cortex-M hardware V1.0 or later. For TMC/ETB trace through the trace buffer, SEGGER lists J-Link PLUS V10 or later.
Specifications
| Part number | 6.68.20 |
|---|---|
| Microcontroller | ST STM32H743 |
| Core | ARM Cortex-M7 |
| Max. CPU clock | 400 MHz |
| Trace | Embedded Trace Macrocell (ETM), 4-bit trace port |
| Max. trace bandwidth | 1064 Mbps (4-bit trace) |
| Trace port clock | 266 MHz (actual trace clock is half the TPIU frequency, sampled on both edges) |
| Debug interfaces | JTAG, SWD, SWO |
| Debug connector | External debug header with trace pins (19-pin JTAG/SWD and trace) |
| Target power | 5V from J-Trace PRO on pins 11 and 13 |
| Test points | All trace signals |
| LEDs | 3, for demo applications |
| Software | J-Link software V6.60d or later; Ozone V3.10b or later |
What's Included
SEGGER publishes no box list for this board, so the order is for the STM32H7 Trace Reference Board itself. The example projects are free downloads from SEGGER's Knowledge Base.
Limitations
- No trace probe is included. Streaming trace needs J-Trace PRO; the trace buffer example needs a J-Link PLUS V10 or later.
- The streaming trace tutorial runs the core at 64 MHz with a 32 MHz trace clock, not at the board's maximum figures.
- SEGGER says the board can be used with other ARM emulators that share the same pinout, but at your own risk.
- SEGGER publishes no dimensions or weight for the board.
Trace Reference Boards Compared
| Model | Microcontroller | Max. CPU clock | Max. trace bandwidth (4-bit) | Debug interfaces | Price ex VAT |
|---|---|---|---|---|---|
| STM32H7 Trace Reference Board (this product) | ST STM32H743, Cortex-M7 | 400 MHz | 1064 Mbps | JTAG, SWD, SWO | £240 |
| iMX RT1050 Trace Reference Board | NXP iMX RT1051/52, Cortex-M7 | 600 MHz | 1056 Mbps | SWD | £240 |
| Cortex-M Trace Reference Board | ST STM32F407, Cortex-M4F | 168 MHz | 672 Mbps | JTAG, SWD, SWO | £19 |
| J-Trace PRO Cortex-M | Streaming trace probe that powers and traces these boards | £1,515 | |||
Typical Applications
Bringing up streaming trace and live code coverage in Ozone on a Cortex-M7 before the first custom STM32H7 boards arrive. Comparing ETB trace buffer capture with a J-Link PLUS against streaming capture with J-Trace PRO on the same target. Probing the trace test points as a signal quality reference while reviewing a new trace connector layout.
The board suits STM32H7 firmware teams and hardware engineers checking trace routing.
Order the STM32H7 Trace Reference Board for £240 ex VAT, or ask us for a formal quotation. See the full range in our SEGGER debug probes collection.
Last reviewed 16/11/2026.
| General | |
|---|---|
| Part number | 6.68.20 |
| Microcontroller | ST STM32H743 |
| Test points | All trace signals |
| LEDs | 3, for demo applications |
| Host and Target Interface | |
| Debug interfaces | JTAG, SWD, SWO |
| Debug connector | External debug header with trace pins (19-pin JTAG/SWD and trace) |
| Performance | |
| Max. CPU clock | 400 MHz |
| Trace | Embedded Trace Macrocell (ETM), 4-bit trace port |
| Max. trace bandwidth | 1064 Mbps (4-bit trace) |
| Trace port clock | 266 MHz (actual trace clock is half the TPIU frequency, sampled on both edges) |
| Power | |
| Target power | 5V from J-Trace PRO on pins 11 and 13 |
| Software and Compatibility | |
| Core | ARM Cortex-M7 |
| Software | J-Link software V6.60d or later; Ozone V3.10b or later |
| Ordering information | |
| Part number (SKU) | 6.68.20 |
| Manufacturer | SEGGER Microcontroller GmbH |
| EAN | 5055383699186 |
| Warranty | 12 mois |
| Shipping weight | 0.02 kg |
-
1 ×
Carte de référence de trace SEGGER STM332H7
Contact us to confirm the full contents of the box.
Questions et réponses
-
Can I Use a J-Link Instead of a J-Trace PRO?
For the trace buffer example, yes: SEGGER lists J-Link PLUS V10 or later for TMC/ETB trace. Streaming trace through the 4-bit trace port needs J-Trace PRO.
-
Does the Example Project Run the STM32H743 at 400 MHz?
No. SEGGER's streaming trace tutorial runs the core at 64 MHz and the trace clock at 32 MHz. The 400 MHz CPU clock and 266 MHz trace port clock are the board's maximum figures from SEGGER's overview.
-
How Does It Differ From the iMX RT1050 Trace Reference Board?
Both use Cortex-M7 cores. The STM32H7 board offers JTAG, SWD and SWO with a 400 MHz maximum CPU clock; the iMX RT1050 board uses SWD with a 600 MHz maximum CPU clock. Choose the one that matches the silicon in your own design.
No questions match your search.