Mikroelektronika d.o.o.
Carte à clic RTC 11
Carte à clic RTC 11
Impossible de charger la disponibilité du service de retrait
Key Features:
- Peut être utilisé pour des applications telles que les applications portables, les appareils portables, les équipements médicaux et similaires.
- Le RTC 11 Click est basé sur l'AB0815, une horloge en temps réel à très faible consommation couplée à un ensemble de fonctionnalités très sophistiquées, d'Abracon LLC.
- Faible consommation d'énergie, batterie de secours, compteurs programmables, alarmes pour les fonctions de minuterie et de surveillance, et plus encore.
- Utilise l'interface SPI
La carte RTC 11 Click Board™ est une carte complémentaire compacte qui contient un circuit intégré d'horloge en temps réel conçu pour maximiser la durée de vie de la batterie et réduire les besoins globaux en batterie dans les applications portables. Cette carte est dotée de l'AB0815, une consommation ultra-faible couplée à une fonction très sophistiquée qui règle l'horloge en temps réel d'Abracon LLC. L'AB0815 comprend un oscillateur intégré pour fournir une faible consommation d'énergie, des fonctions RTC complètes telles que la batterie de secours, des compteurs programmables et des alarmes pour les fonctions de minuterie et de surveillance. Ses besoins en énergie sont inférieurs à ceux de tout autre RTC du secteur (jusqu'à 22 nA) et communique avec le microcontrôleur à l'aide de l'interface SPI. Cette carte Click Board™ convient aux applications telles que les applications portables, les objets portables, les équipements médicaux et similaires.
La carte Click Board™ RTC 11 est prise en charge par une bibliothèque compatible mikroSDK, qui comprend des fonctions qui simplifient le développement logiciel. Cette carte Click Board™ est un produit entièrement testé, prêt à être utilisé sur un système équipé du socket mikroBUS™
How Does The RTC 11 Click Board™Work?
The RTC 11 Click Board™ is based on the AB0815, an ultra-low-power coupled with a highly sophisticated feature set, the real-time clock from Abracon LLC. The AB0815 serves as a full-function RTC and includes 3 feature groups: baseline and advanced timekeeping features, and power management. Functions from each feature group may be controlled via I/O offset mapped registers accessed through SPI serial interface. The baseline timekeeping feature group supports the standard 32.786 kHz crystal oscillation mode for maximum frequency accuracy with an ultra-low current draw of 22nA. This feature also includes a standard set of counters for minutes, hours, dates, months, years, and week-days. A complement of countdown timers and alarms may additionally be set to initiate interrupts or resets on several of the outputs.
The most common configuration as performed on the RTC 11 Click Board™ is a battery backed up RTC, which maintains time and may hold data in RAM. In addition to the AB0815, the RTC 11 Click Board™ is equipped with the button cell battery holder compatible with the 3000TR battery holder, suitable for 12mm Coin Cell batteries. By utilizing an automatic backup switch, the AB0815 can use an external battery power source when there is no power supply on its main power terminals, thus allowing for uninterrupted operation.
The AB0815 communicates with MCU using the standard SPI serial interface that supports modes 0 and 3 with a maximum frequency of 2 MHz. The flexible inputs of the AB0815 can be used to aggregate a variety of interrupt sources, including external digital inputs, analog levels, timers, and alarms into a single interrupt source to an MCU. Based on this, functions like external interrupt or watchdog timer reset could be found on this Click board™ routed on the RST and AN pins of the mikroBUS™ socket labeled as EXI and WDI, as well as the primary and secondary interrupt outputs routed on the INT and PWM pins of the mikroBUS™ socket labeled as IT1 and IT2.
The RTC 11 Click Board™ is designed to be operated only with a 3.3V logic voltage level. A proper logic voltage level conversion should be performed before the Click board™ is used with MCUs with different logic levels. However, the Click board™ comes equipped with a library that contains easy to use functions and an example code that can be used as a reference for further development.
SPECIFICATIONS
| Type | RTC |
| Applications | Can be used for applications such as portable applications, wearables, medical equipment, and similar. |
| On-board modules | The RTC 11 Click Board™ is based on the AB0815, an ultra-low-power coupled with a highly sophisticated feature set, the real-time clock from Abracon LLC. |
| Key Features | Low power consumption, battery backup, programmable counters, alarms for timer and watchdog functions, and more. |
| Interface | SPI |
| Compatibility | mikroBUS |
| Click board size | M (42.9 x 25.4 mm) |
| Input Voltage | 3.3V |
PINOUT DIAGRAM
This table shows how the pinout of the RTC 11 Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| Watchdog Timer Reset | WDI | 1 | AN | PWM | 16 | IT2 | Secondary Interrupt |
| External Interrupt | EXI | 2 | RST | INT | 15 | IT1 | Primary Interrupt |
| SPI Chip Select | CS | 3 | CS | RX | 14 | NC | |
| SPI Clock | SCK | 4 | SCK | TX | 13 | NC | |
| SPI Data OUT | SDO | 5 | MISO | SCL | 12 | NC | |
| SPI Data IN | SDI | 6 | MOSI | SDA | 11 | NC | |
| Power Supply | 3.3V | 7 | 3.3V | 5V | 10 | NC | |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
ONBOARD SETTINGS AND INDICATORS
| Label | Name | Default | Description |
|---|---|---|---|
| LD1 | PWR | - | Power LED Indicator |
RTC 11 CLICK ELECTRICAL SPECIFICATIONS
| Description | Min | Typ | Max | Unit |
|---|---|---|---|---|
| Supply Voltage | -0.3 | 3.3 | 3.8 | V |
| Battery Supply Voltage | 1.4 | - | 3.6 | V |
| Maximum Output Current | -20 | - | 20 | mA |
| SPI Clock Frequency | - | - | 2 | MHz |
| Operating Temperature Range | -40 | - | +85 | °C |
Software Support
We provide a library for the RTC 11 Click Board™ on our LibStock page, as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Library Description
The library covers all the necessary functions that enables the usage of the RTC 11 Click Board™. User can set or read time, date, day of the week, alarm, change settings, or use generic read and write functions.
Key Functions
void rtc11_set_time ( uint8_t t_hrs, uint8_t t_min, uint8_t t_sec );- Function is used to set system time.void rtc11_get_time ( uint8_t *t_hrs, uint8_t *t_min, uint8_t *t_sec );- Function is used to get current system time.void rtc11_get_date ( uint8_t *w_day, uint8_t *d_day, uint8_t *d_mon, uint8_t *d_yrs );- Function is used to get system date.
Example Description
The application is composed of three sections :
- System Initialization - Initializes GPIO, SPI and LOG structures, sets INT and PWM pins as input, and AN, RST and CS pins as output, and start to write log.
- Application Initialization - Initalizes SPI, performs software reset, sets system time and date, and starts clocking system.
- Application Task - Demonstrates use of RTC 11 click board by reading and displaying time and date via USART terminal.
void application_task ( )
{
rtc11_get_time ( &t_hrs, &t_min, &t_sec );
Delay_ms( 10 );
rtc11_get_date ( &w_day, &d_day, &d_mon, &d_yrs );
Delay_ms( 10 );
if ( sec_flag != t_sec )
{
mikrobus_logWrite( " Time: ", _LOG_TEXT );
ByteToStr( t_hrs, log_txt );
ltrim( log_txt );
mikrobus_logWrite( log_txt, _LOG_TEXT );
mikrobus_logWrite( ":", _LOG_TEXT );
ByteToStr( t_min, log_txt );
ltrim( log_txt );
mikrobus_logWrite( log_txt, _LOG_TEXT );
mikrobus_logWrite( ":", _LOG_TEXT );
ByteToStr( t_sec, log_txt );
ltrim( log_txt );
mikrobus_logWrite( log_txt, _LOG_TEXT );
mikrobus_logWrite( "", _LOG_LINE );
mikrobus_logWrite( " Date: ", _LOG_TEXT );
disp_day_of_the_week( w_day );
mikrobus_logWrite( "/", _LOG_TEXT );
ByteToStr( d_day, log_txt );
ltrim( log_txt );
mikrobus_logWrite( log_txt, _LOG_TEXT );
mikrobus_logWrite( "/", _LOG_TEXT );
ByteToStr( d_mon, log_txt );
ltrim( log_txt );
mikrobus_logWrite( log_txt, _LOG_TEXT );
mikrobus_logWrite( "/", _LOG_TEXT );
ByteToStr( d_yrs, log_txt );
ltrim( log_txt );
mikrobus_logWrite( "20", _LOG_TEXT );
mikrobus_logWrite( log_txt, _LOG_TEXT );
mikrobus_logWrite( "/", _LOG_TEXT );
mikrobus_logWrite( "", _LOG_LINE );
}
sec_flag = t_sec;
}
Additional Function :
- void disp_day_of_the_week ( uint8_t w_day ) - Writes the day of the week on USART terminal.
The full application code, and ready to use projects can be found on our LibStock page.
Other mikroE Libraries used in the example:
- SPI
- UART
- Conversions
Additional Notes and Information
Depending on the development board you are using, you may need a USB UART click, USB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.
MIKROSDK
The RTC 11 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Carte à clic RTC 11
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.