Mikroelektronika d.o.o.
Planche à 4 clics H-Bridge
Planche à 4 clics H-Bridge
Impossible de charger la disponibilité du service de retrait
Overview
La carte H-Bridge 4 Click Board™ contient l'AP1010AEN, un pilote de moteur H-Bridge à deux canaux compatible avec une tension de fonctionnement du moteur jusqu'à 18 V et pouvant piloter deux moteurs à courant continu ou un moteur pas à pas. Le circuit de protection est doté d'un circuit de verrouillage de sous-tension, d'un circuit d'arrêt thermique et d'un circuit de protection contre les surintensités, et le circuit de protection contre les surintensités peut être désactivé avec le terminal DIS OCP.
Le H-Bridge 4 Click Board™ prend en charge plusieurs options de connexion et peut être utilisé dans différentes configurations d'application pouvant inclure des moteurs à courant continu ou pas à pas.
How Does The H-Bridge 4 Click Board™ Work?
The main component of the H-Bridge 4 Click Board™ is the AP1010AEN from AsahiKASEI (AKM), which is a two channel H-Bridge motor driver compatible with motor operating voltage up to. This IC is an efficient integrated H-bridge driver, with very low RDS ON output per switch. H-bridge in general, allows the current to flow in one or another direction. The output stages consist of four n-channel mosfets in H-bridge configuration. The outputs are protected against short circuits and over temperature. The bridge is controlled using the inputs IN1, IN2, IN3, and IN4, which are witer to the AN, RST, INT, and PWM pins on the mikroBUS™, respectively.
.jpg)
Its motor operating voltage range is between 6.0V～18V and control power supply is unnecessary. When it comes to its maximum output current (DC) its 0.7A @Ta=25°C and it has H-Bridge On-Resistance, which equals RON(TOP+BOT) = 1.1Ω @Ta=25°C. The Click board™ has an onboard motor voltage supply selection switch, although it is recommended to use the external power supply. The AP1010AEN also has the possibility of a parallel connection, under voltage lockout circuit and the thermal shutdown circuit. The Overcurrent protection circuit is disabled when DIS OCP terminal = "H" and the operating Temperature Range is between -30°C～85°C.
When the internal temperature of the IC reaches the specified temperature (TTSD=155°C), and the H-Bridge driver outputs Hi-Z. When the internal temperature after the detection is lowered about 30°C (TTSDHYS), the driver resumes operation. Restart Temperature = TTSD - TTSDHYS
When the current of 2.6 A or more continues to flow to the H - Bridge driver for 10 μs, all H - Bridge driver outputs are set to Hi - Z, and automatically return after 200 ms. Over current protection circuit can be used by setting the DIS OCP terminal to L level. When not using the overcurrent protection circuit, connect the DIS OCP terminal to the VDC terminal.
SPECIFICATIONS
| Type | Brushed,Stepper |
| Applications | The H-Bridge 4 Click Board™ can be used for a wide range of different applications which require two DC motors or one stepping motor. |
| On-board modules | AP1010AEN, which is a 2ch H-Bridge motor driver compatible with a motor operating voltage 18V |
| Key Features | The protection circuit has under voltage lockout circuit, thermal shutdown circuit, and overcurrent protection circuit, and overcurrent protection circuit can be disabled with the DIS OCP terminal |
| Interface | GPIO |
| Compatibility | mikroBUS |
| Click board size | M (42.9 x 25.4 mm) |
| Input Voltage | 3.3V,5V |
PINOUT DIAGRAM
This table shows how the pinout of the H-Bridge 4 Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| Lead-off detection for IN- | IN1 | 1 | AN | PWM | 16 | IN4 | Lead-off detection for IN- |
| Lead-off detection for IN+ | IN2 | 2 | RST | INT | 15 | IN3 | Lead-off detection for IN+ |
| Enable | EN | 3 | CS | RX | 14 | NC | |
| NC | 4 | SCK | TX | 13 | NC | ||
| NC | 5 | MISO | SCL | 12 | NC | ||
| NC | 6 | MOSI | SDA | 11 | NC | ||
| Power Supply | 3.3V | 7 | 3.3V | 5V | 10 | 5V | Power Supply |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
ONBOARD SETTINGS AND INDICATORS
| Label | Name | Default | Description |
|---|---|---|---|
| LD1 | PWR | - | Power LED Indicator |
| JP1 | VM SEL | - | Select motor voltage |
Software Support
We provide a library for the H-Bridge 4 Click Board™ on our LibStock page, as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Library Description
The library covers all the necessary functions to control the H-Bridge 4 Click Board™. The H-Bridge 4 Click Board™ communicates with the target board through the AN, INT, PWM, RST and CS lines on MikroBUS. This library offers functions for setting or clearing of any and every of the five pins used for communication, also user can use functions that enable or disable clockwise or counter-clockwise motion, as well as standby mode and brake for both channels.
Key Functions
void hbridge4_motorAStandby()- Function is used to put motor A into standby.void hbridge4_motorACW()- Function is used to put motor A into clockwise motion.void hbridge4_motorABrake()- Function is used to brake motor A to a halt.
Example Description
The application is composed of three sections :
- System Initialization - Initializes GPIO and LOG structures, sets AN, INT, PWM, RST and CS pins as output.
- Application Initialization - Initialization driver enables GPIO and also starts write log.
- Application Task - (code snippet) This example demonstrates the use of the H-Bridge 4 Click Board™ by putting A motor in standby mode, then spinning it in clockwise direction and applying brake function, and then spinning it in counter-clockwise direction and applying brake function again.
void applicationTask()
{
mikrobus_logWrite( "The motor A is in standby mode", _LOG_LINE );
hbridge4_motorAStandby();
Delay_ms( 100 );
mikrobus_logWrite( "The motor A turns clockwise", _LOG_LINE );
hbridge4_motorACW();
Delay_ms( 2000 );
mikrobus_logWrite( "The motor A applies brake", _LOG_LINE );
hbridge4_motorABrake();
Delay_ms( 1000 );
mikrobus_logWrite( "The motor A turns counter-clockwise", _LOG_LINE );
hbridge4_motorACCW();
Delay_ms( 2000 );
mikrobus_logWrite( "The motor A applies brake", _LOG_LINE );
hbridge4_motorABrake();
Delay_ms( 1000 );
}
The full application code, and ready to use projects can be found on our LibStock page.
Other mikroE Libraries used in the example:
- UART
Additional Notes and Information
Depending on the development board you are using, you may need USB UART click, USB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.
MIKROSDK
The H-Bridge 4 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Software Support
We provide a library for the H-Bridge 4 Click Board™ on our LibStock page, as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Library Description
The library covers all the necessary functions to control the H-Bridge 4 Click Board™. The H-Bridge 4 Click Board™ communicates with the target board through the AN, INT, PWM, RST and CS lines on MikroBUS. This library offers functions for setting or clearing of any and every of the five pins used for communication, also user can use functions that enable or disable clockwise or counter-clockwise motion, as well as standby mode and brake for both channels.
Key Functions
void hbridge4_motorAStandby()- Function is used to put motor A into standby.void hbridge4_motorACW()- Function is used to put motor A into clockwise motion.void hbridge4_motorABrake()- Function is used to brake motor A to a halt.
Example Description
The application is composed of three sections :
- System Initialization - Initializes GPIO and LOG structures, sets AN, INT, PWM, RST and CS pins as output.
- Application Initialization - Initialization driver enables GPIO and also starts write log.
- Application Task - (code snippet) This example demonstrates the use of the H-Bridge 4 Click Board™ by putting A motor in standby mode, then spinning it in clockwise direction and applying brake function, and then spinning it in counter-clockwise direction and applying brake function again.
void applicationTask()
{
mikrobus_logWrite( "The motor A is in standby mode", _LOG_LINE );
hbridge4_motorAStandby();
Delay_ms( 100 );
mikrobus_logWrite( "The motor A turns clockwise", _LOG_LINE );
hbridge4_motorACW();
Delay_ms( 2000 );
mikrobus_logWrite( "The motor A applies brake", _LOG_LINE );
hbridge4_motorABrake();
Delay_ms( 1000 );
mikrobus_logWrite( "The motor A turns counter-clockwise", _LOG_LINE );
hbridge4_motorACCW();
Delay_ms( 2000 );
mikrobus_logWrite( "The motor A applies brake", _LOG_LINE );
hbridge4_motorABrake();
Delay_ms( 1000 );
}
The full application code, and ready to use projects can be found on our LibStock page.
Other mikroE Libraries used in the example:
- UART
Additional Notes and Information
Depending on the development board you are using, you may need USB UART click, USB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.
MIKROSDK
The H-Bridge 4 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.