Mikroelektronika d.o.o.
Planche à clic Spirit 2 (États-Unis)
Planche à clic Spirit 2 (États-Unis)
Impossible de charger la disponibilité du service de retrait
Le Spirit 2 Click Board™ est doté du SP1ML-915, un module RF à très faible consommation et entièrement intégré qui fonctionne dans la bande ISM 915 MHz. Ce Click Board™ peut être utilisé pour ajouter une connectivité sans fil à n'importe quelle application, sans nécessiter d'expérience approfondie en communication RF. Le module intègre tous les composants requis, notamment le microcontrôleur STM32L1 32 bits, une antenne à puce compacte et les circuits associés. Le module SP1ML-915 prend en charge plusieurs types de schémas de modulation, notamment 2-FSK, GFSK, GMSK, OOK et ASK, ce qui lui permet de répondre à différentes exigences de transmission RF.
La carte Click Board™ SPIRIT 2 est supportée par une bibliothèque compatible mikroSDK, qui comprend des fonctions qui simplifient le développement logiciel. Cette carte Click Board™ est un produit entièrement testé, prêt à être utilisé sur un système équipé du socket mikroBUS™.
Remarque : le SPIRIT 2 Click Board™ est conçu et certifié pour être utilisé en Amérique (région 2) ; pour l'Europe (région 1), vous pouvez utiliser le Spirit Click Board™
Thanks to very low power consumption, high level of integration, and simple UART communication interface, the SPIRIT 2 Click Board™ can be used to add wireless connectivity to a wide range of different applications, including data acquisition equipment, security systems, home and building automation, wireless sensor network, wireless metering, etc. It is also an ideal solution for developing various IoT-based applications, which demand low power consumption and wireless connectivity.
How Does The SPIRIT 2 Click Board™ Work?
The SPIRIT 2 Click Board™ uses the SP1ML-915, a low power RF module with integrated MCU, from STMicroelectronics. The module incorporates all the necessary components packed in a compact size of 14 x 13.4 x 2.5 mm. The STM32L1, an integrated 32-bit MCU is designed with maximised power saving in mind, offering many power-saving features. This allows even lower power consumption for the entire module, providing data rates up to 500 kbps. RF signal modulation schemes facilitate RF transmission requirements, allowing fine-tuning of the range and power consumption.
The primary function of the SP1ML-915 module is to be used as a wireless serial cable replacement. The Click board™ features the SWD compatible programming header, allowing custom firmware to be uploaded to the integrated MCU. However, that may destroy the factory firmware and void the warranty.
Offering a simple UART interface, combined with the lowered power consumption, it represents a perfect solution for adding wireless connectivity, especially to IoT applications. Since the module is designed to be used without an extensive RF communication experience, it is straightforward to be used. The Click board™ offers two modes of operation: Operating mode and Command mode.
In operating mode, data received from the host on the UART interface will be wirelessly transmitted by the module using the current configuration settings for frequency, data rate, modulation and output power. Also, any data received by the module that meets the configured filtering criteria, will be output to the UART interface.
Command mode allows the configuration of the SP1ML-915 module. When the Click board™ receives an escape sequence "+++", followed by at least of 500ms of RX inactivity, it will enter the Command mode. By using a number of simple AT commands, the developer has the possibility to configure the operating parameters of the device. The complete list of AT commands is provided in the datasheet of the SP1ML-915 module.
A note should be taken not to send the escape sequence during the regular operation, if entering the Command mode is not intended.
Besides using the aforementioned escape sequence, the module can be put into the Command mode by driving the CMD pin of the Click board™ to a LOW logic level. A HIGH logic level on this pin will force the Click board™ into the Operating mode. The Click board™ should be reset after changing the state on this pin.
To reset the SP1ML-915 module, a LOW logic level to the RST pin of the Click board™ should be applied. While a LOW logic level is present on the RST pin, the SP1ML-915module will be held in the RESET mode.
The SHD pin of the Click board™ will drive the Click board™ into the power down mode by applying the LOW logic level on it. A HIGH logic level will wake up the device.
The data traffic is indicated by a LED labelled as TX/RX. However, the indicator should be enabled to use it. Consult the datasheet of the SP1ML-915 for more information.
The Click board™ can be interfaced with both 3.3V and 5V MCUs without needing external components. Thanks to the TXB0106, 6-Bit bidirectional voltage-level translator, the Click board™ can be simply used with a wide range of different MCUs.
SPECIFICATIONS
| Type | Sub-1 GHz Transceivers |
| Applications | It can be used to add wireless connectivity to a wide range of different applications, including data acquisition equipment, security systems, home and building automation, wireless sensor network, wireless metering, etc |
| On-board modules | SP1ML-915, a low-power RF module with integrated MCU from STMicroelectronics |
| Radio Region | America |
| Key Features | Low power consumption, high level of integration, a large number of RF modulation schemes, simple use over the UART interface, data rate up to 500 kbps |
| Interface | GPIO,UART |
| Compatibility | mikroBUS |
| Click board size | M (42.9 x 25.4 mm) |
| Input Voltage | 3.3V or 5V |
PINOUT DIAGRAM
This table shows how the pinout on SPIRIT 2 Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| NC | 1 | AN | PWM | 16 | SHD | Shut down | |
| Reset | RST | 2 | RST | INT | 15 | NC | |
| Command mode | CMD | 3 | CS | RX | 14 | TX | UART RX |
| NC | 4 | SCK | TX | 13 | RX | UART TX | |
| NC | 5 | MISO | SCL | 12 | NC | ||
| NC | 6 | MOSI | SDA | 11 | NC | ||
| Power Supply | 3.3V | 7 | 3.3V | 5V | 10 | 5V | Power Supply |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
ONBOARD SETTINGS AND INDICATORS
| Label | Name | Default | Description |
|---|---|---|---|
| PWR | PWR | - | Power LED Indicator |
| TX/RX | TX/RX | - | Data traffic LED indicator |
| LOGIC SEL | LOGIC SEL | Left | Logic voltage selection level: left position 3.3V, right position 5V |
Software Support
We provide a library for the SPIRIT 2 Click on our LibStock page and a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Library Description
The library contains all the necessary functions for working with SPIRIT modules. Generic parser
Key Functions
spirit2_cmdSingle- Sends provided command to the module.spirit2_moduleReset- Reset module.spirit2_modulePower- Turn on module.
Example Description
The application is composed of three sections :
- System Initialization - Initializes all necessary GPIO pins, UART used for the communication with SPIRIT module and UART used for infromation logging .
- Application Initialization - Initializes driver, power on module .
- Application Task - running in the parallel core state machine. In the RX mode, the unit reads data received from another device and sends a message in TX mode every 2 seconds. .
void applicationTask()
{
spirit2_process();
if( _userAppMode == _SPIRIT2_APP_TX_MODE)
{
mikrobus_logWrite("** SPIRIT SENDS MESSAGE.....", _LOG_LINE);
spirit2_cmdSingle(&_txBuffer[0]);
Delay_ms( 2000 );
}
}
Additional Functions :
All additional functions such as timer initialization and default handler.
The full application code, and ready to use projects can be found on our LibStock page.
Other mikroE Libraries used in the example:
StringConversionUART
Depending on the development board you are using, you may need USB UART Click Board™, USB UART 2 Click Board™ or RS232 Click Board™ to connect to your PC for development systems with no UART to the USB interface on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.
MIKROSDK
The SPIRIT 2 Click Board™ board is supported by the mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click Board™ board demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Planche à clic Spirit 2 (États-Unis)
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.