Mikroelektronika d.o.o.
Carte à clic Nano Power 2
Carte à clic Nano Power 2
Impossible de charger la disponibilité du service de retrait
Le Nano Power 2 Click Board™ est un comparateur de tension à très faible puissance, destiné aux applications portables et alimentées par batterie. Il permet de détecter une différence de deux potentiels de tension, appliqués sur deux broches d'entrée. L'appareil peut détecter les différences de manière très précise, évitant les oscillations qui peuvent se produire lorsque les deux tensions d'entrée sont égales en utilisant une hystérésis interne.
La carte Nano Power 2 Click Board™ offre le choix de sélectionner l'une des tensions d'entrée à partir de la référence fixe interne de 1,2 V, ou en réglant les deux tensions d'entrée par les potentiomètres intégrés.
The Nano Power 2 Click Board™ is a very low-power voltage comparator, aimed at portable and battery-powered applications. It allows detecting a difference of two voltage potentials, applied on two input pins. The device can detect differences very precisely, avoiding oscillations that can occur when both input voltages are equal by employing an internal hysteresis. Nano Power 2 Click Board™ offers a choice to select one of the input voltages from the internal fixed reference of 1.2V, or by setting both input voltages by the on-board potentiometers.
The current consumption of the Nano Power 2 Click Board™ ensures that there is no significant load to the measured inputs, and compared to other similar devices, it is several magnitudes lower. It produces clean output signals, which are used to indicate the result of the comparison. Both the logic level and the power supply levels can be selected between 3.3V and 5V, allowing a wide range of MCUs to be used with this Click Board™. With its two high-quality potentiometers, this Click Board™+J1984™ represents a unique testing platform for the integrated nanoPower comparator IC used on the Nano Power 2 Click Board™.
How Does The Nano Power 2 Click Board™ Work?
The Click Board™ is equipped with an integrated comparator IC, labelled as MAX40000AUT12+, a nanoPower comparator with built-in reference, produced by Maxim Integrated. This company offers several variants of the same IC, of which the used IC variant offers reference voltage of 1.2V on one of its pins. This reference voltage can be used at the comparator input, providing an accurate reference voltage throughout the fully operational temperature range, if required by the custom application.
The IC itself requires a very low number of external components. It has two input pins, used as the comparator inputs. Each of these inputs can use -0.2V up to VCC + 0.2V. The VCC is the power supply voltage, and it can be selected via the SMD jumper labelled as LOGIC, between the 3.3V and 5V rails from the mikroBUS™. One of the comparator inputs, labelled as IM on the MAX40000 IC, is routable to either the on-board potentiometer (P1) or the REF pin of the IC, which provides the referent voltage of 1.2V. The routing can be done by another SMD jumper, labelled as REF SEL. The second comparator input (labelled as IP on the MAX40000 IC) is routed to the second on-board potentiometer (P2). Both potentiometers can be used to set any voltage between the GND and VCC, which is selected by the LOGIC jumper, as described above.
As mentioned before, the comparator has two inputs. One of them it is the inverting input and it is labelled as IM. The other input is a non-inverting input, labelled as IP. When the IP voltage becomes higher than the IM voltage, the output state becomes logic HIGH; otherwise, the output is set to a LOW state. A special case is when both voltages are very close, or at the same level, at any given moment. This would result in an appearance of oscillation at the output due to noise or parasitic feedback. To cope with this problem, an internal hysteresis of ±2.5mV is applied.
The output of the MAX40000 IC is routed to the mikroBUS™ INT pin, labelled as OUT on the Click Board™. The output stage employs a unique break-before-make topology, capable of rail-to-rail operation with up to ±2mA loads. The output stage also uses a unique design, which minimizes supply current surges when the switching occurs, resulting in very clean output and low EM radiation. The MAX40000 has a push-pull output stage topology, which can both sink and source the current.
Working with the Nano Power 2 Click Board™ is very easy and straightforward. Only a single pin is used, which can be used to either trigger an interrupt (therefore it is routed to the INT pin), or its status can be read via the input pin of the host MCU. However, MikroElektronika provides a library that contains a function which can be used for simplified control of the Nano Power 2 Click Board™. The library also contains an example application, which demonstrates the use of the function. This example application can be used as a reference for custom designs.
Software Support
We provide a demo application for Nano Power 2 Click Board™ on our Libstock page, as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Library Description
Library initializes and defines GPIO driver and performs control of device voltage.
For more details check the documentation.
Key Functions
NANOPW2_RETVAL_T nanopw2_checkOutput( void )- TFunction gets output voltage from the comparator.
Example Description
The application is composed of three sections:
- System Initialization - Initializes OUT (INT) pin as an input.
- Application Initialization - Initializes GPIO driver.
- Application Task - (code snippet) - Checks the comparator's output and logs output value on USB UART. The hysteresis in a comparator creates two trip points: one for upper threshold (VTRIP+) and one for lower threshold (VTRIP-) for voltage transitions on the input signal. When the comparator’s input voltages are equal, the hysteresis effectively causes one comparator input to move quickly past the other, thus taking the input out of the region where oscillation occurs. The output voltage is high (1) when noninverted input voltage rises above the hysteresis and stays high until noninverted input voltage falls below the hysteresis. Then the output goes low and stays low until noninverted input voltage rises above the hysteresis. This is an example where the inverted input voltage is fixed and the noninverted input voltage is varied. If the inputs were reversed, the example would be the same, except with an inverted output.
void applicationTask()
{
outCheck = nanopw2_checkOutput();
if (outCheck != outCheckPrev)
{
WordToStr( outCheck, text );
mikrobus_logWrite( "OUT is: ", _LOG_TEXT );
mikrobus_logWrite( text, _LOG_LINE );
outCheckPrev = outCheck;
}
}
The full application code, and ready to use projects can be found on our Libstock page.
Additional notes and information
Depending on the development board you are using, you may need USB UART click, USB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.
mikroSDK
The Nano Power 2 Click Board™ is supported by mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant click board demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Carte à clic Nano Power 2
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.