Mikroelektronika d.o.o.
Tableau à clic Spirit
Tableau à clic Spirit
Impossible de charger la disponibilité du service de retrait
Overview
La carte Spirit Click Board™ est équipée du module RF ultra-basse consommation SP1ML 868 MHz. La carte est conçue pour utiliser une alimentation 3,3 V et des niveaux de tension E/S 3,3 V ou 5 V. Elle communique avec le microcontrôleur cible via l'interface UART, avec des fonctionnalités supplémentaires fournies par les broches suivantes sur la ligne MikroBUS : PWM, RST, CS.
Il peut être utilisé pour envoyer et recevoir sans fil des données UART.
The SPIRIT Click Board™ carries the SP1ML 868MHz ultra low-power RF module. The board is designed to use 3.3V power supply and 3.3V or 5V I/O voltage levels. It communicates with the target MCU over UART interface, with additional functionality provided by the following pins on the mikroBUS™ line: PWM, RST, CS.
It can be used to wirelessly send and receive UART data.
SP1ML 868MHZ RF MODULE FEATURES
SP1ML is based on the SPIRIT1 RF sub-GHz transceiver (with integrated SMPS), STM32L1 microcontroller, integrated filter/balun, and chip antenna.
There are two operational modes, command mode and operating mode. The command mode allows module configuration and status interrogation using an extended 'AT' style command set. In operating mode the module serves its primary purpose as a wireless transceiver.
In operating mode the module uses only 13.5mA, 2.2mA in command mode, and even lower in standby with just 1.4µA. This kind of power consumption makes it ideal for smart devices that send small amounts of data.
The module has an integrated antenna and crystal.
SPECIFICATIONS
| Type | Sub-1 GHz Transceivers |
| Applications | Security systems, mobile health and medicine applications, IoT, wireless metering, etc. |
| On-board modules | SP1ML 868MHz ultra low-power RF module |
| Radio Region | Europe |
| Key Features | Low data rate, low power sub-GHz transceiver |
| Interface | GPIO,UART |
| Compatibility | mikroBUS |
| Click board size | M (42.9 x 25.4 mm) |
| Input Voltage | 3.3V or 5V |
PINOUT DIAGRAM
This table shows how the pinout of SPIRIT Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| NC | 1 | AN | PWM | 16 | SHDN | Shutdown | |
| Reset input, active low | RST | 2 | RST | INT | 15 | NC | |
| Command mode | CMD | 3 | CS | TX | 14 | TXD | UART transmit data |
| NC | 4 | SCK | RX | 13 | RXD | UART receive data | |
| NC | 5 | MISO | SCL | 12 | NC | ||
| NC | 6 | MOSI | SDA | 11 | NC | ||
| Power supply | +3.3V | 7 | 3.3V | 5V | 10 | +5V | Power supply |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
JUMPERS AND SETTINGS
LOGIC SEL - used to select 3.3 or 5V logical level for UART communication (J1A in the schematic).
Software Support
Code examples for the SPIRIT Click Board™, written for MikroElektronika hardware and compilers are available on Libstock.
GENERAL DESCRIPTION
The library implements communication protocol between the MCU host and SPIRIT click module. It can work in two modes, command mode and operating mode. The command mode allows module configuration and status interrogation using an extended ‘AT’ style command set. In operating mode the module serves its primary purpose as a wireless transceiver. It uses asynchronous approach to issue commands and receive responses via callback functions.
CODE SNIPPET
The code snippet shows an example callback function for the ATO command. It checks if the response is OK to change from library state to operating mode.
01 static bool on_ato(char* response)
02 {
03 if(strcmp(response, "OK") == 0)
04 {
05 LOG_INFO("Entered operating mode.");
06
07 spirit_mode(SPIRIT_OPERATING_MODE);
08 }
09 else
10 {
11 LOG_ERROR("Failed to enter to operation mode...");
12 }
13
14 return true;
15 }
Features
- Configurable command buffer size.
- Ring buffer for receiving data via UART
- Supported mikroC compilers for ARM, PIC32, PIC, FT90.
- Asynchronous command issuing.
Software Support
Code examples for the SPIRIT Click Board™, written for MikroElektronika hardware and compilers are available on Libstock.
GENERAL DESCRIPTION
The library implements communication protocol between the MCU host and SPIRIT click module. It can work in two modes, command mode and operating mode. The command mode allows module configuration and status interrogation using an extended ‘AT’ style command set. In operating mode the module serves its primary purpose as a wireless transceiver. It uses asynchronous approach to issue commands and receive responses via callback functions.
CODE SNIPPET
The code snippet shows an example callback function for the ATO command. It checks if the response is OK to change from library state to operating mode.
01 static bool on_ato(char* response)
02 {
03 if(strcmp(response, "OK") == 0)
04 {
05 LOG_INFO("Entered operating mode.");
06
07 spirit_mode(SPIRIT_OPERATING_MODE);
08 }
09 else
10 {
11 LOG_ERROR("Failed to enter to operation mode...");
12 }
13
14 return true;
15 }
Features
- Configurable command buffer size.
- Ring buffer for receiving data via UART
- Supported mikroC compilers for ARM, PIC32, PIC, FT90.
- Asynchronous command issuing.
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.