Mikroelektronika d.o.o.
Tableau à 3 clics couleur
Tableau à 3 clics couleur
Impossible de charger la disponibilité du service de retrait
Le Color 3 Click Board™ est une carte complémentaire MikroBUS dotée d'un capteur de couleur TCS3771 (également appelé convertisseur lumière-numérique) et d'une LED infrarouge à faisceau étroit. Le circuit peut également fonctionner comme un capteur de proximité.
TCS3771 is a RGBC sensor: it can detect Red, Green, Blue and clear light. The IC performs well under a variety of lighting conditions. For example, it can be covered with different attenuation materials.
As a proximity sensor it has a large dynamic range of operation. It can take short distance measurements behind dark glass; or it can be configured for longer distance measurement, for example, human presence detection in front of monitors or laptops.
For power-saving, TCS3771 has an internal state machine that can put the device into a low power mode between successive RGBC and proximity measurements.
TCS3771 is also fast enough to give off proximity information at a high rate of repetition. This makes it useful for proximity detection in portable devices (such as a phone coming near to a speaker's ear).
The Color 3 Click Board™ communicates with the target MCU through the mikroBUS™ I2C interface, with additional functionality provided by an INT pin. Designed to use a 3.3 power supply only.
Software Support
The following code snippet shows how to send temperature readings from the Color 3 Click Board™ to a TFT display.
1 void main()
2 {
3 //Local Declarations
4 uint8_t _i2c_address = 0x29;
5 color_t my_color;
6
7 // GPIOs
8 GPIO_Digital_Input( &GPIOD_BASE, _GPIO_PINMASK_10 );
9 Delay_ms(300);
10
11 // I2C
12 I2C1_Init_Advanced( 100000, &_GPIO_MODULE_I2C1_PB67 );
13 Delay_ms(300);
14
15 //Color 3
16 color_3_init( _i2c_address );
17 Delay_ms(300);
18
19 color_3_get_rgb_data( &my_color );
20
21 while(1)
22 {
23
24 }
25 }
Code examples that demonstrate the usage of the Color 3 Click Board™ with MikroElektronika hardware, written for mikroC for ARM, AVR, dsPIC, FT90x, PIC and PIC32 are available on Libstock
Software Support
The following code snippet shows how to send temperature readings from the Color 3 Click Board™ to a TFT display.
1 void main()
2 {
3 //Local Declarations
4 uint8_t _i2c_address = 0x29;
5 color_t my_color;
6
7 // GPIOs
8 GPIO_Digital_Input( &GPIOD_BASE, _GPIO_PINMASK_10 );
9 Delay_ms(300);
10
11 // I2C
12 I2C1_Init_Advanced( 100000, &_GPIO_MODULE_I2C1_PB67 );
13 Delay_ms(300);
14
15 //Color 3
16 color_3_init( _i2c_address );
17 Delay_ms(300);
18
19 color_3_get_rgb_data( &my_color );
20
21 while(1)
22 {
23
24 }
25 }
Code examples that demonstrate the usage of the Color 3 Click Board™ with MikroElektronika hardware, written for mikroC for ARM, AVR, dsPIC, FT90x, PIC and PIC32 are available on Libstock
Tableau à 3 clics couleur
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.