Mikroelektronika d.o.o.
Tableau à barres 4 clics
Tableau à barres 4 clics
Impossible de charger la disponibilité du service de retrait
Le Bar Graph 4 Click Board™ est une carte complémentaire compacte qui contient quatre écrans graphiques à barres LED verts à quatre segments. Cette carte est équipée du TLC59283, un pilote de diode électroluminescente (LED) à courant constant à 16 canaux de Texas Instruments. Selon le VCC de fonctionnement, chaque canal peut être contrôlé individuellement avec un simple protocole de communication série SPI compatible avec les niveaux logiques 3,3 V ou 5 V. Il est également livré avec une valeur de courant constant des 16 canaux définie par une seule résistance et une broche GPIO utilisée pour désactiver toutes les sorties pendant la mise sous tension et le verrouillage des données de sortie afin d'éviter les affichages d'images indésirables pendant ces périodes. Ce Click Board™ convient à la création de divers types de VU-mètres, d'indicateurs d'état, de différents types de compteurs et d'appareils similaires.
Le BarGraph 4 Click Board™ est pris en charge par une bibliothèque compatible mikroSDK, qui comprend des fonctions qui simplifient le développement logiciel. Ce Click Board™ est un produit entièrement testé, prêt à être utilisé sur un système équipé du socket mikroBUS™.
How Does The BarGraph 4 Click Board™ Work?
The BarGraph 4 Click Board™ as its foundation uses the TLC59283, a 16-channel, constant-current sink light-emitting diode (LED) driver from Texas Instruments. Each channel can be individually controlled with a simple serial communications protocol compatible with 3.3V or 5V logic levels depending on the operating VCC. It also comes with a constant-current value of all 16 channels, determined by an external resistor R2 with a value of 2.2kΩ, limiting the current to 24mA. You can find the exact value of the current per channel, as well as the corresponding resistance value for a given current, in the attached datasheet.
In the upper part on the front side of the board, marked with the characters A, B, C, and D, four green four-segment LED bar graph displays, the HLMP-2550 are placed. The Green HLMP-2500 series LEDs use a liquid phase GaPepitaxial layer on a GaP substrate. These light bars are designed for various applications where a large bright light source is required, making this Click board™ suitable for creating different VU meters, status indicators, counters, and similar devices.
The TLC59283 communicates with MCU using the standard SPI serial interface with a maximum frequency of 35MHz. It has a 16-bit shift register and an output ON/OFF data latch. Both shift register and data latch are 16 bits long and used to turn the constant-current outputs on and off. It also comes with one GPIO pin, routed on the RST pin of the mikroBUS™ socket, used to turn off all outputs during Power-On and output data latching to prevent unwanted image displays during these times.
When the device is initially powered on, the data in the 16-bit shift register and output on or off data latch are not set to default values. Therefore, the output ON/PFF data must be written to the data latch before turning the constant-current output ON. The RST pin should be high when powered on because the constant-current may be turned ON due to random data in the output on or off data latch.
The BarGraph 4 Click Board™ can operate with both 3.3V and 5V logic voltage levels selected via the VCC SEL jumper. This way, it is allowed for both 3.3V and 5V capable MCUs to use the SPI communication lines properly. However, the Click board™ comes equipped with a library containing easy-to-use functions and an example code that can be used, as a reference, for further development.
SPECIFICATIONS
| Type | Bargraph,LED Segment |
| Applications | Can be used for creating various types of VU meters, status indicators, different types of counters, and similar devices |
| On-board modules | TLC59283 - 16-channel, constant-current sink light-emitting diode (LED) driver from Texas Instruments |
| Key Features | 16-channel constant-current LED Driver, each channel individually controlled, output force-off pin, four green four-segment LED bar graph displays, bright uniform light emitting areas, and more |
| Interface | SPI |
| Compatibility | mikroBUS |
| Click board size | L (57.15 x 25.4 mm) |
| Input Voltage | 3.3V or 5V |
PINOUT DIAGRAM
This table shows how the pinout on BarGraph 4 Click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| NC | 1 | AN | PWM | 16 | NC | ||
| Output Channels Force-OFF |
RST | 2 | RST | INT | 15 | NC | |
| SPI Chip Select | CS | 3 | CS | RX | 14 | NC | |
| SPI Clock | SCK | 4 | SCK | TX | 13 | NC | |
| SPI Data OUT | SDO | 5 | MISO | SCL | 12 | NC | |
| SPI Data IN | SDI | 6 | MOSI | SDA | 11 | NC | |
| Power Supply | 3.3V | 7 | 3.3V | 5V | 10 | 5V | Power Supply |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
ONBOARD SETTINGS AND INDICATORS
| Label | Name | Default | Description |
|---|---|---|---|
| LD1 | PWR | - | Power LED Indicator |
| JP1 | VCC SEL | Left | Logic Level Voltage Selection 3V3/5V: Left position 3V3, Right position 5V |
BARGRAPH 4 CLICK ELECTRICAL SPECIFICATIONS
| Description | Min | Typ | Max | Unit |
|---|---|---|---|---|
| Supply Voltage | 3.3 | - | 5 | V |
| Output Current per Channel | - | 24 | - | mA |
| Operating Temperature Range | -40 | +25 | +85 | °C |
Software Support
We provide a library for the BarGraph 4 Click Board™ as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
The package can be downloaded/installed directly from NECTO Studio Package Manager (recommended), downloaded from our LibStock™ or found on Mikroe GitHub account.
Library Description
This library contains an API for the BarGraph 4 Click driver.
Key Functions
bargraph4_cfg_setup- Config Object Initialization function.bargraph4_init- Initialization function.
Example Description
This example demonstrates the use of the BarGraph 4 click board.
The application is composed of three sections :
void application_task ( void )
{
for ( bargraph4_level_t cnt = BARGRAPH4_LEVEL_0; cnt <= BARGRAPH4_LEVEL_4; cnt++ )
{
bargraph4_set_channel_level( &bargraph4, BARGRAPH4_CHANNEL_A, cnt );
bargraph4_set_channel_level( &bargraph4, BARGRAPH4_CHANNEL_B, cnt );
bargraph4_set_channel_level( &bargraph4, BARGRAPH4_CHANNEL_C, cnt );
bargraph4_set_channel_level( &bargraph4, BARGRAPH4_CHANNEL_D, cnt );
log_printf( &logger, " All channels set to level %urnn", ( uint16_t ) cnt );
Delay_ms( 1000 );
}
}
The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on Mikroe GitHub account.
Other mikroE Libraries used in the example:
- MikroSDK.Board
- MikroSDK.Log
- Click.BarGraph4
Additional Notes and Information
Depending on the development board you are using, you may need a USB UART click, USB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.
MIKROSDK
The BarGraph 4 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Tableau à barres 4 clics
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.