Ir directamente a la información del producto
1 de 3

Mikroelektronika d.o.o.

Stepper 8 Click Board™

Stepper 8 Click Board™

SKU: MIKROE-4157

Precio habitual
£18.00 exc VAT
£21.60 inc VAT
Precio habitual £18.00 GBP Precio de oferta
£18.00 exc VAT
£21.60 inc VAT
Oferta Agotado
Los gastos de envío se calculan en la pantalla de pago.
If no stock shown above, check availability

Formas de pago

  • American Express
  • Visa
  • Mastercard
  • Maestro
  • PayPal
  • Apple Pay
  • Google Pay
  • Bank transfer
Ver todos los detalles

Descripción general

The Stepper 8 Click Board™ is a motor control add on board based on TC78H670FT from Toshiba. A clock-in and serial controlled Bipolar Stepping Motor Driver which can drive a 128 micro-stepping motor with a power supply ranging from 2.5V to 16V for a wide range of applications include USB-powered, battery-powered, and standard 9-12V system devices. A perfect solution for driving stepper motors in security cameras, portable printers, handheld scanners, pico-projectors, smartphones and many more.

How Does The Stepper 8 Click Board™ Work?

The Stepper 8 Click Board™ can be used with bipolar step motor, coils should be connected to the onboard screw terminals. There are two terminals, used to connect each of the step motor coils. The third connector is used to connect an external voltage, ranging from 2.5V to 16V, depending on the used motor voltage requirements and current of 2A. The maximum output current may be further limited in view of thermal considerations, depending on ambient temperature and board conditions. It should be noted that without a valid external voltage connected to this terminal, the motor will not work.

stepper 8 click inner

The Stepper 8 Click Board™ can operate a bipolar stepper motor in full, half, quarter, 1/8, 1/16, 1/32, 1/64, 1/128 step operation. Thanks to internal safety features, such as thermal shutdown (TSD), over current (ISD), motor load open (OPD) and under voltage lockout(UVLO), this Click board™ is perfectly suited for rapid development of various stepper motor applications.

This TC78H670FTG integrated driver offers a simple interface, featuring a set of pins used to control the functions of the step motor. Since the number of pins exceeds the available mikroBUS™ general purpose pins, an additional port expander IC is used, exposing a 2-wire I2C interface for the communication with the host MCU. The port expander IC is the PCA9538, an 8-bit port expander with the I2C interface.

The MODE0-3 pins can be selected Serial mode or CLK-IN mode. The control mode is set up by the input state of the MODE0-3 pins after releasing standby mode. Under the serial mode, it performs setting and motor control in the following 32 bit format using SPI on mikroBUS™. For the motor control, each current value is set in the serial setting, and the output is updated to the set current value at the timing of the LATCH signal. More information about using Serial mode or CLK-IN mode can be find in TC78H670FTG datasheet.

To allow both Serial mode or CLK-IN mode on mikroBUS™ a TC7WH157 two channel multiplexer from Toshiba is used. Selection is done using I2C communication with PCA9538 port expander and changing state of SELECT pins on multiplexers.

SPECIFICATIONS

Type Stepper
Applications The Stepper 8 Click Board™ is suitable for Security cameras, portable printers, handheld scanners, pico-projectors, smartphones and many more
On-board modules TC78H670FTG
Key Features Advanced Current Detection System, Built-in Dual H Bridges, Low on-resistance, Multi error detect functions
Interface GPIO,I2C,SPI
Compatibility mikroBUS
Click board size L (57.15 x 25.4 mm)
Input Voltage 3.3V or 5V

PINOUT DIAGRAM

This table shows how the pinout on the Stepper 8 Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes Pin Mikrobus logo.png Pin Notes
MODE3 MD3 1 AN PWM 16 MD2 MODE2
MODE0 MD0 2 RST INT 15 ERR Enable/Error
MODE1 MD1 3 CS RX 14 NC
SPI Clock SCK 4 SCK TX 13 NC
NC 5 MISO SCL 12 SCL I2C Clock
SPI Data IN SDI 6 MOSI SDA 11 SDA I2C Data
Power Supply 3.3V 7 3.3V 5V 10 5V Power Supply
Ground GND 8 GND GND 9 GND Ground

ONBOARD SETTINGS AND INDICATORS

Label Name Default Description
LD1 PWR - Power LED Indicator
JP2 VCC SEL Left Logic level voltage selection: left position 3V3, right position 5V
JP1 VM Right Power supply selection: left position - External supply, right position - On-board supply
JP3, JP4 ADDR SEL Right Slave address selection: left position 1, right position 0
VR1 VR1 - Current threshold reference adjustment trimmer

STEPPER 8 CLICK ELECTRICAL SPECIFICATIONS

Description Min Typ Max Unit
Supply Voltage 2.5 - 16 V
Output Current 0 - 2 A
fOSCM 656 1266 3290 kHz
fchop 41 79 206 kHz

Overview
CategoryStepper
ApplicationsSecurity cameras, portable printers, handheld scanners, pico-projectors, smartphones and many more
Key components
On-board modulesTC78H670FT
Features
Key featuresAdvanced Current Detection System, Built-in Dual H Bridges, Low on-resistance, Multi error detect functions
Interfaces
InterfaceI2C, SPI, GPIO
CompatibilitymikroBUS™
Electrical
Input voltage3.3V or 5V
Physical
Click board sizeL (57.15 x 25.4 mm)
Compliance
Country of originSerbia
RoHSCompliant
Información de pedido
Referencia (SKU)MIKROE-4157
FabricanteMikroelektronika d.o.o.
EAN8606018717606
Garantía12 months
Peso de envío0.022 kg
  • 1 × Stepper 8 Click Board™

Contacte con nosotros para confirmar el contenido completo de la caja.

Preguntas a nuestros ingenieros

Preguntas y respuestas

No questions have been asked about this product yet. Ask our engineers below and we'll reply by email.

¿No encuentra la respuesta? Pregunte a nuestros ingenieros.

Hacer una pregunta

Ask Our Engineers About This Product

Your question goes to the Debug Store technical team. We answer by email, and useful questions may be added to this page without your name or email address.

We reply within 24 hours.