
Características principales
Descripción general
The J-Trace PRO RISC-V is a streaming trace probe for RV32 and RV64 RISC-V cores, using RISC-V N-Trace BTM. It connects over USB 3.0 SuperSpeed or Gigabit Ethernet, downloads at up to 4.0 MB/s and has a 1.2V to 5V target interface. It combines J-Link debugging with unlimited instruction trace, live code coverage and live code profiling.
The SEGGER J-Trace PRO RISC-V (part number 8.22.00) is a streaming trace probe for RV32 and RV64 RISC-V cores, using RISC-V N-Trace BTM, with a USB 3.0 SuperSpeed and Gigabit Ethernet host link, download speeds up to 4.0 MB/s and a 1.2V to 5V target interface. It combines J-Link debugging with unlimited instruction trace, live code coverage and live code profiling. It suits firmware teams bringing up and validating RISC-V microcontrollers and SoCs that implement N-Trace.
Streaming N-Trace for RISC-V Cores
Streaming trace sends data continuously to the PC instead of stopping when a buffer fills, so a recording can run long enough to catch a rare fault or a program that ends up stuck in a fault handler. SEGGER's Knowledge Base lists N-Trace BTM for RISC-V and supported cores of RV32 and RV64 on this model. Devices without a SEGGER trace reference must implement the RISC-V trace components that SEGGER describes in its N-Trace documentation.
Debug and Trace Connectors
The probe has two target connectors: the 20-pin JTAG/SWD connector used across the J-Link range, with a 14-pin adapter available, and a 19-pin 0.05" JTAG/SWD and Trace connector that carries the trace clock and four trace data lines. Pin assignments for the 20-pin connector are in our SEGGER J-Link 20-pin connector pinout guide. SEGGER's feature table for this model lists JTAG, cJTAG and SWD debug interfaces, and the probe can supply 5V to the target.
Full J-Link PRO Debug Capability
J-Trace PRO RISC-V is also a full J-Link debug probe for RISC-V. It includes the full set of J-Link PRO licences, including Unlimited Flash Breakpoints. SEGGER allows Ozone, its debugger and trace analysis tool, to be used free of charge with a J-Trace PRO, including for commercial use. Ozone is SEGGER's recommended tool for trace analysis; debugging works from any J-Link compatible IDE. Software runs on Windows, Linux and macOS, including ARM64 and Apple Silicon hosts.
The Ethernet data lines are isolated to IEEE 802.3 (1500 Vrms for one minute). The shield is not, so SEGGER recommends an unshielded twisted pair cable where that isolation matters.
What's Included
- J-Trace PRO RISC-V probe
- 20-pin 0.05" target ribbon cable
- 20-pin 0.1" target ribbon cable
- USB 3.0 cable
Specifications
| Host interface | USB 3.0 SuperSpeed; Gigabit Ethernet |
|---|---|
| Target interface | JTAG/SWD 20-pin (14-pin adapter available); JTAG/SWD + Trace 19-pin 0.05" |
| Trace | Streaming trace; N-Trace BTM (RISC-V) |
| Supported cores | RISC-V RV32, RV64 |
| Target interface voltage (VIF) | 1.2V to 5V |
| Target interface speed | Max. 50 MHz |
| Download speed | Up to 4.0 MB/s |
| Power supply | USB powered, max. 400mA |
| Reset type | Open drain with 100 Ohm series resistor, can be pulled low or tristated |
| Trace capacitive load | 3 pF J-Trace plus 8 pF cable (typical) |
| Dimensions (without cables) | 123mm x 68mm x 30mm |
| Weight (without cables) | 120g |
| Operating temperature | +5°C to +60°C |
| Storage temperature | -20°C to +65°C |
| Relative humidity | Max. 90% rH, non-condensing |
| EMC | EN 55022, EN 55024 |
| Host OS | Windows and Linux (x86-64, ARM64); macOS (x86-64, Apple Silicon) |
Limitations
- RISC-V only. SEGGER's feature table for this model lists no ARM ETM, PTM or ETB trace, no SWO and no ARM monitor-mode debugging; for ARM and RISC-V in one probe, choose the J-Trace PRO.
- No SWD multi-drop, VCOM or CMSIS-DAP v1 (HID) mode.
- Trace needs the target to implement N-Trace and bring the trace pins out to a connector; SEGGER notes that trace setup depends on the target hardware design.
- SEGGER's package list for this model does not include the Cortex-M Trace Reference Board.
J-Trace PRO RISC-V Compared with the Other J-Trace PRO Models
| Model | Trace architectures | Cortex-M Trace Reference Board in box | Price ex VAT |
|---|---|---|---|
| J-Trace PRO RISC-V (this product) | RISC-V (RV32, RV64) | Not listed | £2,005 |
| J-Trace PRO | ARM Cortex-A, Cortex-R, Cortex-M and RISC-V | Yes | £3,005 |
| J-Trace PRO Cortex | ARM Cortex-A, Cortex-R and Cortex-M | Yes | £2,005 |
| J-Trace PRO Cortex-M | ARM Cortex-M | Yes | £1,515 |
Typical Applications
Instruction trace on an RV32 microcontroller to find the code path that leads to an intermittent exception. Live code coverage on an RV64 core to show which paths a test suite exercised before release. Trace on a SiFive core bitstream on an ARTY board, connected through the SiFive-ARTY Trace Adapter.
Choose the J-Trace PRO RISC-V when all your trace targets are RISC-V.
Order the J-Trace PRO RISC-V for £2,005 ex VAT. Check that your device implements N-Trace with the trace pins connected, or ask us for a formal quotation. See the full range in our SEGGER debug probes collection.
Last reviewed 16/11/2026.
| General | |
|---|---|
| Reset type | Open drain with 100 Ohm series resistor, can be pulled low or tristated |
| Host and Target Interface | |
| Host interface | USB 3.0 SuperSpeed; Gigabit Ethernet |
| Target interface | JTAG/SWD 20-pin (14-pin adapter available); JTAG/SWD + Trace 19-pin 0.05" |
| Target interface voltage (VIF) | 1.2V to 5V |
| Performance | |
| Trace | Streaming trace; N-Trace BTM (RISC-V) |
| Target interface speed | Max. 50 MHz |
| Download speed | Up to 4.0 MB/s |
| Trace capacitive load | 3 pF J-Trace plus 8 pF cable (typical) |
| Power | |
| Power supply | USB powered, max. 400mA |
| Software and Compatibility | |
| Supported cores | RISC-V RV32, RV64 |
| Host OS | Windows and Linux (x86-64, ARM64); macOS (x86-64, Apple Silicon) |
| Physical | |
| Dimensions (without cables) | 123mm x 68mm x 30mm |
| Weight (without cables) | 120g |
| Environmental | |
| Operating temperature | +5°C to +60°C |
| Storage temperature | -20°C to +65°C |
| Relative humidity | Max. 90% rH, non-condensing |
| EMC | EN 55022, EN 55024 |
| Información de pedido | |
| Referencia (SKU) | 8.22.00 |
| Fabricante | SEGGER Microcontroller GmbH |
| EAN | 5055383618293 |
| Garantía | 12 months |
| Peso de envío | 0.5 kg |
- 1 ×J-Trace PRO RISC-V trace probe
- 1 ×20-pin, 0.05" target ribbon cable
- 1 ×20-pin, 0.1" target ribbon cable
- 1 ×USB 3.0 cable
SEGGER J-Trace PRO RISC-V Debug Probe comparado con SEGGER J-Trace PRO Cortex Trace Debugger , Depurador de traza en streaming SEGGER J-Trace PRO Cortex-M (8.18.00) and SEGGER J-Trace PRO Trace Probe en 15 especificaciones.
| Especificación | Este producto
SEGGER J-Trace PRO RISC-V Debug Probe8.22.00Disponible bajo pedido |
SEGGER J-Trace PRO Cortex Trace Debugger8.20.00Disponible bajo pedido |
Depurador de traza en streaming SEGGER J-Trace PRO Cortex-M (8.18.00)8.18.00En stock |
SEGGER J-Trace PRO Trace Probe8.24.00Disponible bajo pedido |
|---|---|---|---|---|
| Debug architectures | RISC-V (RV32, RV64) | ARM Cortex-A, Cortex-R and Cortex-M | ARM Cortex-M (incl. SC000, SC300) | ARM Cortex-A/R/M, legacy ARM, ARM China STAR-MC, RISC-V, Cadence Tensilica, Microchip PIC32, Renesas RX and RH850, Silicon Labs EFM8 |
| ARM Cortex trace | Not supported | ETM, PTM, ETB | ETM, ETB (solo Cortex-M) | ETM, PTM, ETB |
| RISC-V trace | N-Trace BTM | Not supported | No compatible | N-Trace BTM |
| Trace pins | 4-bit (TRACECLK, TRACEDATA[0..3]) on 19-pin 0.05" connector | 4-bit (TRACECLK, TRACEDATA[0..3]) on 19-pin 0.05" connector | 4 bits (TRACECLK, TRACEDATA[0..3]) en conector de 19 pines y 0.05" | 4-bit (TRACECLK, TRACEDATA[0..3]) on 19-pin 0.05" connector |
| Streaming trace | Supported | Supported | Compatible | Supported |
| On-board trace buffer | 64 MB | 64 MB | 64 MB | 64 MB |
| Host interface | USB 3.0 SuperSpeed and Gigabit Ethernet | USB 3.0 SuperSpeed and Gigabit Ethernet | USB 3.0 SuperSpeed y Gigabit Ethernet | USB 3.0 SuperSpeed and Gigabit Ethernet |
| Target interface speed | Max. 50 MHz | Max. 50 MHz | Máx. 50 MHz | Max. 50 MHz |
| Download speed | Up to 4 MB/s | Up to 4 MB/s | Hasta 4 MB/s | Up to 4 MB/s |
| Target interface voltage (VIF) | 1.2 V to 5 V | 1.2 V to 5 V | 1.2 V a 5 V | 1.2 V to 5 V |
| SWO | Not supported | Supported | Compatible | Supported |
| ARM monitor mode debugging | Not supported | ARMv7-M and ARMv8-M | ARMv7-M y ARMv8-M | ARMv7-M and ARMv8-M |
| 5 V target supply | Supported | Supported | Compatible | Supported |
| Trace reference board in the box | Not included | Cortex-M Trace Reference Board | Cortex-M Trace Reference Board | Cortex-M Trace Reference Board |
| Software licences | Full set of J-Link PRO licences (incl. Unlimited Flash Breakpoints); Ozone included | Full set of J-Link PRO licences (incl. Unlimited Flash Breakpoints); Ozone included | Conjunto completo de licencias J-Link PRO (incl. Unlimited Flash Breakpoints); Ozone incluido | Full set of J-Link PRO licences (incl. Unlimited Flash Breakpoints); Ozone included |
| Precio | £2,005 | £2,005 | £1,515 | £3,005 |
Preguntas y respuestas
-
Can the J-Trace PRO RISC-V Be Used as a Normal J-Link Debug Probe?
Yes. It is a full J-Link debug probe for RISC-V, with the full set of J-Link PRO licences, including Unlimited Flash Breakpoints, and works with J-Link software and J-Link compatible IDEs.
-
Does the J-Trace PRO RISC-V Trace ARM Cortex Devices?
No. SEGGER's Knowledge Base lists no ETM, PTM or ETB trace for this model. The J-Trace PRO (8.24.00) traces both ARM Cortex and RISC-V.
-
What Does the Target Need for Trace?
The device must implement RISC-V N-Trace and the trace clock and data pins must be wired to the 19-pin 0.05" connector. SEGGER asks for contact about devices not on its tested list; it needs J-Link support and a public evaluation board with the trace pins connected.
No questions match your search.