Mikroelektronika d.o.o.
DC Motor 5 Click Board
DC Motor 5 Click Board
Couldn't load pickup availability
The DC Motor 5 Click Board™ carries the DRV8701 brushed DC motor gate driver from Texas Instruments.
The DC Motor 5 Click Board™ is designed to run on an external power supply. It communicates with the target MCU over the following pins on the MikroBUS line: AN, RST, CS, PWM, and INT.
![Mikroelektronika d.o.o. MIKROE-2699 DC Motor 5 Click Board - The Debug Store UK](http://thedebugstore.com/cdn/shop/products/mikroelektronika-d-o-o-click-board-dc-motor-5-click-board-30256946905277.jpg?v=1685211775&width=1445)
![Mikroelektronika d.o.o. MIKROE-2699 DC Motor 5 Click Board - The Debug Store UK](http://thedebugstore.com/cdn/shop/products/mikroelektronika-d-o-o-click-board-dc-motor-5-click-board-30256946839741.jpg?v=1685010715&width=1445)
![Mikroelektronika d.o.o. MIKROE-2699 DC Motor 5 Click Board - The Debug Store UK](http://thedebugstore.com/cdn/shop/products/mikroelektronika-d-o-o-click-board-dc-motor-5-click-board-28819329876157.jpg?v=1685160646&width=1445)
![Mikroelektronika d.o.o. MIKROE-2699 DC Motor 5 Click Board - The Debug Store UK](http://thedebugstore.com/cdn/shop/products/mikroelektronika-d-o-o-click-board-dc-motor-5-click-board-28819329810621.jpg?v=1685160655&width=1445)
The DC Motor 5 Click Board™ carries the DRV8701 brushed DC motor gate driver from Texas Instruments. The click is designed to run on an external power supply. It communicates with the target MCU over the following pins on the mikroBUS™ line: AN, RST, CS, PWM, and INT.
DRV8701 DRIVER FEATURES
The DRV8701 is an H-bridge gate driver (also called a pre-driver or controller). The device integrates FET gate drivers in order to control four external NMOS FETs. The device can be powered with a supply voltage between 5.9V and 45V.
Internal protection functions are provided: under-voltage lockout, charge pump faults, overcurrent shutdown, short-circuit protection, pre-driver faults, and overtemperature.
How Does The DC Motor 5 Click Board™ Work?
The motor's velocity and direction can be adjusted with two PWM input signal's.
SPECIFICATIONS
Type | Brushed |
Applications | Industrial brushed-DC motors, robotics, home automation, etc. |
On-board modules | DRV8701 Brushed DC Motor Full-Bridge Gate Driver |
Key Features | supply voltage between 5.9V and 45V |
Interface | GPIO |
Compatibility | mikroBUS |
Click board size | M (42.9 x 25.4 mm) |
Input Voltage | External |
PINOUT DIAGRAM
This table shows how the pinout of the DC Motor 5 Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
Notes | Pin | ![]() |
Pin | Notes | |||
---|---|---|---|---|---|---|---|
Sense comparator output | SNSO | 1 | AN | PWM | 16 | IN1 | Input signal 1 |
Device sleep mode | SLEEP | 2 | RST | INT | 15 | IN2 | Input signal 2 |
Fault indication pin | FAULT | 3 | CS | TX | 14 | NC | |
NC | 4 | SCK | RX | 13 | NC | ||
NC | 5 | MISO | SCL | 12 | NC | ||
NC | 6 | MOSI | SDA | 11 | NC | ||
NC | 7 | 3.3V | 5V | 10 | NC | ||
Ground | GND | 8 | GND | GND | 9 | GND | Ground |
BUTTONS AND LEDS
Designator | Name | Type | Description |
---|---|---|---|
LD1 | PWR | LED | Power Indication LED |
TB1 | VM | CD | Voltage input connector |
TB2 | Out_M | CD | Motor connector |
MAXIMUM RATINGS
Description | Min | Typ | Max | Unit |
---|---|---|---|---|
Supply VOltage | 5.9 | 45 | V | |
Source Current | 6 | 150 | mA | |
Sink Current | 12.5 | 300 | mA | |
Applied PWM signal | 100 | kHz | ||
Operating ambient temperature | -40 | 125 | ℃ |
Software Support
Code examples for the DC Motor 5 Click Board™, written for MikroElektronika hardware and compilers are available on Libstock.
CODE SNIPPET
The following code snippet shows an example of the DC Motor 5 Click Board™ usage. It will detect button press, and change the state of the control pins, putting the motor into one of the 4 possible states.
01 void main() 02 { 03 systemInit(); 04 05 while (1) 06 { 07 // Coast 08 if (Button(&GPIOD_IDR, 1, 1, 1)) 09 { 10 IN1_PIN = 0; 11 IN2_PIN = 0; 12 } 13 14 // Reverse 15 if (Button(&GPIOD_IDR, 2, 1, 1)) 16 { 17 IN1_PIN = 0; 18 IN2_PIN = 1; 19 } 20 21 // Brake 22 if (Button(&GPIOD_IDR, 3, 1, 1)) 23 { 24 IN1_PIN = 1; 25 IN2_PIN = 1; 26 } 27 28 // Forward 29 if (Button(&GPIOD_IDR, 4, 1, 1)) 30 { 31 IN1_PIN = 1; 32 IN2_PIN = 0; 33 } 34 35 } 36 }
DC Motor 5 Click Board
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.
![banner Image](http://thedebugstore.com/cdn/shopifycloud/shopify/assets/no-image-2048-5e88c1b20e087fb7bbe9a3771824e743c244f437e4f8ba93bbf7b11b53f7824c_medium.gif)