Mikroelektronika d.o.o.
Clicker Board 2 for Kinetis
Clicker Board 2 for Kinetis
Couldn't load pickup availability
With two mikroBUS sockets on Click Board™ 2 for Kinetis, you can take advantage of the huge potential of Click Boards™, the constantly expanding range of over 300 add-on boards. Blend different functionalities together and come up with new and original inventions. That's just two Click Boards™ and your project is half-way done. Go ahead and play with a few ideas right away.
Focus on your main idea because Click Board™ 2 will take care of the details for you: your prototype already has a power management system in place. The on-board LTC3586-1 IC will provide 3.3V or 5V to the Click Boards™. It turns the USB port into a battery charger. For convenience, Clicker 2 Board™ for Kinetis features a reset button and an ON/OFF switch (you can also connect an external ON/OFF switch).
Technical Specifications
Thousands of possibilities with Click Boards
With two mikroBUS™ sockets on clicker 2, you can take advantage of the huge potential of Click boards™, the constantly expanding range of over 1210 Click boards™ add-on boards. Blend different functionalities together and come up with new and original inventions. That's just two clicks and your project is half-way done. Go ahead and play with a few ideas right away.
Programming
To make your prototyping experience as convenient as possible, clicker 2 for Kinetis is preprogrammed with a USB HID bootloader. Just download our mikroBootloader application and you're ready to upload your firmware. On-board mikroProg for Kinetis connector enables programming through external programmer/debugger.
Power Management
The Clicker 2 for Kinetis features LTC®3586, a highly integrated power management and battery charger IC that includes a current limited switching PowerPath manager. LTC®3586 also enables battery charging over a USB connection. You can supply power to the board with a micro USB cable provided in the package. On-board voltage regulators provide the appropriate voltage levels to each component on the board.
Powering Your Inventions
Focus on your main idea because clicker 2 will take care of the details for you: your prototype already has a power management system in place. The onboard LTC®3586-1 IC will provide 3.3V or 5V to the clicks. It turns the USB port into a battery charger. For convenience, clicker 2 for Kinetis features a reset button and an ON/OFF switch (you can also connect an external ON/OFF switch).
Processor
- MK64FN1M0VDC12 has 1MB Flash
- Runs at 120 MHz
- 256 KB boot SRAM
Connectivity
- 52 programmable GPIOs
- 2 x mikroBUS connectors
- USB Mini-B connector
Expanding Your Ideas
No idea is too big for Clicker 2. Let your train of thought lead you anywhere. Consider all options, explore all directions. More click boards? Additional electronics? Done and done. clicker 2 has the same pocket-size form factor and the same pair of 1x26 connection pads as mikromedia boards. This makes it compatible with mikromedia shields letting you expand your device any way you want.
mikroBUS Shield for mikromedia 
mikromedia connect shield 
mikromedia PROTO shield 
Battery Boost Shield 
Hardware Debugging
Efficiently eradicate any bugs and iron out your code until it's wrinkle free and your clicker 2 device works perfectly—use mikroProg™ for Kinetis. It's a fast hardware debugger and programmer that exploits the MCU's integrated encryption module, enabling secure firmware updating.
USB HID BOOTLOADER Inside
To make your prototyping experience as convenient as possible, clicker 2 for Kinetis is preprogrammed with a USB-HID bootloader. Just download our mikroBootloader application and you're ready to upload your firmware.
SPECIFICATION TABLE
| Type | Clicker 2 |
| Architecture | ARM (32-bit) |
| Programming | Bootloader, External |
| Silicon Vendor | NXP |
| mikroBUS No. | 2 |
| Supply Voltage | Battery, USB |
| Category | Clicker 2 |
Clicker Board 2 for Kinetis
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.