Lineeye LE-3500XR-E Multi Protocol Analyzer

It can be used for connection of TTL communication signals and external trigger signals.
If you use both at the same time, please purchase extra.

The RS-422/485 measurement port is removable terminal block

The RS-422/485 cable can be directly connected to the port. When you temporarily need to disconnect the analyzer from the monitor line, you do not need to screw off the cable, you just need to detach the terminal.

Supports DSUB 9-pin and DSUB 25-pin of RS-232C as standard

The RS-232C measurement port adopts the DSUB25 pin where the transmission/reception synchronization clock signal is arranged. As the produt includes a DSUB 25-pin monitor cable, DSUB 25-pin to 9-pin conversion adapter, and DSUB 9-pin monitor cable, it can be connected to both DSUB 25-pin and DSUB 9-pin of a RS-232C device.

Various Line Monitor Displays According to the Communication Protocol

Flexible support for ASYNC asynchronous communication from legacy to present

It can monitor asynchronous communciation in which one data consists of a start bit, data bits (5 to 8 bits), parity bit (none, odd number, even, mark, space, or multiprocessor bit definition MP), and stop bit (1, 2 bits).
The MSB first transfer of the legacy protocol can be selected, and the suppress (removal) of the flag character is supported by the ASYNC-PPP protocol.

Bit synchronous communication such as character synchronous communication and HDLC

BSC communication synchronized with the SYNC character and HDLC/SDLC synchronized with the flag bit can be measured. It supports BCC/FCS (block check code/frame check sequence) judgment and HDLC address filters. NRZ, NRZI, FM0, FM1 data modulation formats can be selected.

Support Modbus, a fieldbus protocol, as a standard

Even in high-speed Modbus communication, it can accurately detect the idle time (silent interval) for 3.5 characters and then separate and measure the communication frames. It supports Modbus-ASCII and Modbus-RTU data formats, and the LRC/CRC frame check is automatically performed according to the data format, thus error judgment display and error trigger are available.

You can easily monitor SPI and I²C of TTL level communication

You can easily monitor I²C and SPI communication used in sensor modules, AD conversion ICs, memory ICs, etc. Also, transmission/reception tests can be performed on the master side or slave side.

2C monitoring example>

Logic analyzer function and signal voltage measurement function

The analzyer has a logic analyzer function which can measure the timing of communication lines with a time resolution of up to 50 nsec. It also has a function to measure RS-232C signals and TTL voltage amplitude which are difficult for testers to hit.

Statistical Analysis Function

Statistics of the number of transmitted/received data, the number of frames, and the number of times the trigger condition is satisfied are displayed in a graph in units of 1 to 240 minutes. You can see the communication traffic (line usage rate) and error occurrence tendency for each time zone.

Smoothly swipe and display long-term trend recording data

Mega-speed measurement, arbitrary speed can be set with 4 significant figures

It supports half-duplex/full-duplex line monitors up to 2.048 Mbps, simulation transmission test, and BERT measurement. As it has a high-precision DPLL circuit, you can set any communication speed (baud rate) of 50 bps to 2.048 Mbps separately for transmission and reception with 4 significant digits. Therefore, it is possible to support devices with special communication speeds, and it is also possible to intentionally send test data with slightly different communication speeds from this analyzer to evaluate the speed margin of the device under test.

Long time recording by AUTO SAVE function

By using the auto save function, you can save communication data to SDHC card or USB memory continuously for a long time. As the data is saved in multiple log files of the specified size (#nnnnnnn.DT: n is a sequential number in the order of saving), you can narrow down the communication logs of before and after the failure from the time stamp of the file in the time zone when the communication failure occurred.

Safely records measured communication files even if the battery runs out suddenly

In the conventional model, if the power is turned off while recording the communication log file, the file may be damaged and communication data cannot be analyzed. With this model, even if the internal battery is exhausted after a bus power failure, the communication status up to that point can be safely saved in a file.

*: When you use an extremely depleted battery, the file protection process for right before the battery run out may not be in time and the file may be damaged.

*1: When 1 kilobyte data is repeatedly transmitted by full duplex with intervals of 1m second idle time for each. Both transmission and reception data consume 4 byte of memory for each capture. *2: When using SD-8GX and SD-32GX (optional)

Saving the captured data to USB flash or SD card	External memory up to 32GB
	Supports optional SD card (such as SD-32GX) or USB flash

Added a mode to prevent overwriting of communication log files

Besides the Restart mode - the communication log files are recorded up to the specified number of files, the communication log file with the smallest file number is deleted and the communication data is endlessly recorded in a new communication log file - and the Append mode - measurement starts from the continuation of the existing communication log file -, the MAX stop mode - automatically stops the measurement after recording the specified number of communication log files - has been added.

AUTO RUN automatic measurement function - convenient for unattended measurement

It can automatically execute a measurement for the specified period by specifying the date and time of measurement start and end.

With the settings on this screen, measurement starts every day at 12:30 and automatically ends at 13:00.

6 Simulation Modes

The analyzer has 6-mode simulation function in which it performs transmission and reception tests as a communication partner of the device under test.

MANUAL mode

You can send the test data registered in the transmission data table of [0] to [F] of 10 groups by pressing the [0] to [F] keys. In this mode, you can easily test the communication procedure by key operation while on the monitor screen checking the response from the target device in development.

FLOW mode

In this mode, flow control procedures such as X-on/off or RTS-CTS of asynchronous communication are simulated on the transmitting side or the receiving side. You can check whether the device under test is operating correctly in response to the transmission interruption request.

ECHO mode

In this mode, the received data is returned inside the unit and returned. It can be used for a communication test with a terminal in echo back mode and as a BERT loopback point.

POLLING mode

In this mode, the analyzer operates for simulation as a slave side or a master side in the multi-drop (1:N connection) polling communication procedure. You can test the procedure including error checking process without writing a program.

BUFFER mode

In this mode, you can select the send side or receive side from the send/receive data captured in the capture memory using the line monitor function and send the data as is. It can be used for a reproduction test of communication data captured on site.

PROGRAM mode

In this mode, you can flexibly simulate a communication protocol with condition judgment by creating a program of dedicated commands.

Explanation of the example
000: Label 000
001: Send the string "ABC"
002: Wait for receive frame from the test target
003: If there is a character string "OK" in the received frame, go to label 000
004: Buzzer a sound if the string "OK" is not included
005: Program end

PROGRAM Mode Commands

Equipped With BERT Function - Comparable to a Dedicated Machine

It is equipped with a bit error rate test function that can measure the communication error rate with parameters compliant with ITU-T Recommendation G.821, and can evaluate the quality of the communication line and isolate fault points.

Full use of measurement data by PC connection

The PC link software is attached

By using the included PC link software LE-PC300R (light), you can utilize the measurement data on your PC.
>> PC link software "LE-PC300R"

■ Offline data display/text conversion

By connecting an SDHC card or USB memory (in which measurement data files are saved) to a PC, you can open and display multiple data files on the PC at the same time or convert the file to .text / .CSV file. Of course, you can also analyze the data file sent by email from another department.

>> Text conversion example
>> CSV conversion example

■ Records measurement data on PC via remote connection

By connect the analyzer to a PC with USB or Wi-Fi, you can remotely control the communication analyzer from the PC or remotely monitor the measured data of the communication analyzer. When connecting via Wi-Fi, you can select the station mode (when connecting via an external Wi-Fi access point) or the access point mode (when connecting directly to tthe analyzer which acts as a W-Fi access point).

Multiple analyzers can be controlled at the same time from one PC to which the PC link software is installed. You can also access the analyzer from a desktop computer connected to an external Wi-Fi access point connected to the LAN.

The computer and analyzer have a 1:1 connection, which is convenient when an external Wi-Fi access point cannot be used.

*: Wi-Fi function is available only in Japan, USA, Canada, and EU nations where the product is needed to be compliant with RE directive (2014/53/EU).

Obtain the communication log file while continuing measurement

By using the LE file downloader (lefiledownload.exe) which can be downloaded free of charge from the LINEEYE website, you can connect the analyzer and a PC via Wi-Fi and obtain the communication log file (saved in the storage device inserted to the analyzer) to the PC. The imported communication log file can be opened and displayed by PC link software for analysis.

  *: The communication log file in saveing process by the auto save function cannot be downloaded.

Firmware update

The latest firmware with new features and improvements will be posted on our website. If you download it to your computer, you can easily update it to the latest version via a USB cable.

Improved Measurement Efficiency

Auto Configuration Function

It analyzes the received communication data and can automatically sets basic measurement conditions such as communication speed, character framing, data code, synchronization character, BCC/FCS, etc.

* Automatic setting is available only for ASYNC, SYNC/BSC, HDLC/SDLC. If the communication data volume is small or the data has many errors, it may not be able to configure correctly. * The maximum supported speed of automatic setting is 460.8kbps.

The trigger function supports an external trigger

Trigger function that can specify up to 4 sets of conditions such as transmission and reception of specific data and measurement action after the condition is satisfied. It is very useful for investigating an intermittent failures often found in communication systems. As you can spcify the meet of a trigger condition as the other trigger condition, you can analyze the complex event involving sequence-like condition determination. Using the external trigger input/output, you can use the analyzer in combination with external device contacts and external measuring instruments such as oscilloscopes for various situations.

When the switch is turned on (external trigger input is L), the character string ABC is sent, and when the character string 123 is received as a response, the trigger signal (external trigger output 2) is supplied to the oscilloscope.
Trigger 0 and 1 are enabled, external trigger input 0 of line state is set for both factors, trigger 2 is enabled by trigger 0 action, and data transmission is set for trigger 1 action. Set the detection of the character string 123 to the trigger 2 factor and the OT2 pulse output to the trigger 2 action.
Set it to the simulation MANUAL mode and register the character string ABC in the send data table.

Offline Analysis and Data Search

The measured data can be freely scrolled by swiping the screen. You can mark the data you want to read, scroll the display, and then return to the mark position with one touch. The powerful search function can display and count error data, specific character strings, time stamp data in a specified range, etc.

Auto backup function

In addition to 100 MB of capture memory, it has a built-in battery-backed SRAM area. At the end of measurement, the latest measurement data of approximately 512 Kbytes is automatically backed up in this SRAM area and automatically loaded to the capture memory when the power is turned on. This allows you to use it as if you were using an old model in which the measured data did not disappear when the power was turned off.

PC Compatible File Management

The analyzer setting data and measurement data can be saved in the SDHC card or USB memory as a FAT management format file compatible with a PC. Of course, since files can be used interchangeably between each model, you can use the measurement data saved by a LE-2500XR on site and analyze it in detail by the LE-3500XR in the development department.

* Measurement data files can be used mutually between LE-3500XR(A)/LE-3500(XR/R)/LE-2500(XR/R)/LE-1500(R). However, some files and data may not be available when using a file saved by a higher model on a lower model and when using a file saved on a new model on a conventional model . Also, files saved with extended options with different firmware cannot be used because the data is incompatible.

You can check the type, name, size, and creation date/time of the saved file by switching the storage device for file operation.

When many files are saved, you can specify the file type you want to display on the file operation screen at the file filter setting screen.

This screen shows the setting to display only the files automatically saved by the auto save function from 0:00 January 10, 2020 to 23:59 February 25, 2020.

Bus-Powered. Lithium-Ion Battery is Built-In.

You can power the analyzer by bus power from the micro USB connector and charge the built-in lithium-ion battery. The battery can be operated continuously for 7 hours, thus there is no need to worry even in places where AC power is difficult to use.

You can extend the battery life by using a commercially available 5V mobile battery.
(With a 13,000mAh mobile battery it can operate for more than 30 hours continuously)