Zu Produktinformationen springen
1 von 3

OMICRON-Lab

OMICRON Lab Test Card Set - Series-Thru

OMICRON Lab Test Card Set - Series-Thru

Replacement set of 32 Series-Thru test cards and one calibrator for the B-TCA, best suited to high impedances from 1 kΩ to 1 MΩ.

SKU: P0011464

Normaler Preis
€206,95 EUR exc tax
Normaler Preis Verkaufspreis
€206,95 EUR exc tax
Sale Ausverkauft
Versand wird beim Checkout berechnet
Check Availability before Ordering

Zahlungsmethoden

  • American Express
  • Visa
  • Mastercard
  • Maestro
  • PayPal
  • Apple Pay
  • Google Pay
  • Banküberweisung
Vollständige Details anzeigen

Overview

The OMICRON Lab Test Card Set - Series-Thru is a replacement set of 32 red Series-Thru test cards and one Series-Thru calibrator (Open, Short, Load) for the B-TCA test card adapter. Series-Thru is rated best of the four B-TCA setups for high impedance, 1 kΩ to 1 MΩ, within the B-TCA's DC to 450 MHz range (up to 50 MHz on a Bode 100), with DUTs up to about 9 mm contact to contact. The cards fit the 100-pin card-edge connector of the B-TCA, used with a Bode 100 or Bode 500.

The OMICRON Lab Test Card Set - Series-Thru (P0011464) is a replacement set of 32 Series-Thru test cards and one Series-Thru calibrator for the B-TCA test card adapter. OMICRON Lab rates Series-Thru as the best of the four B-TCA setups for high impedance, with an optimal DUT impedance magnitude of 1 kΩ to 1 MΩ, within the B-TCA's recommended DC to 450 MHz range, on a Bode 500 (10 mHz to 450 MHz) or Bode 100 (1 Hz to 50 MHz) vector network analyser. Order it to restock the red Series-Thru cards when you characterise high-impedance passive SMD components.

Series-Thru Impedance Measurement From 1 kΩ to 1 MΩ

On a Series-Thru test card the DUT is soldered between the two pads in the signal line, the signal pad and the CH2 pad, so the test signal passes through it. This two-port arrangement gives the best high-impedance sensitivity of the four setups. Below 1 kΩ the 50 Ω termination and source impedance degrade sensitivity, so for low-impedance parts move to the Shunt-Thru set. The maximum recommended DUT size is about 9 mm from one contact to the other.

Series-Thru Calibrator: Open, Short and Load

The red Series-Thru calibrator carries Open, Short and Load references, with the Short doubling as the Thru and the Load at 50 Ω ±0.1%. In the Bode Analyzer Suite, run Open first, then Short with the Short-Delay Time set to 0 ps, then Load. A Thru-only calibration using the Short element is possible, but OMICRON Lab notes that it does not remove impedance mismatch errors, so a full Open, Short and Load calibration is the one to use for high-impedance work.

Soldering and Fitting B-TCA Test Cards

Each test card is a 1.57 mm (nominal) PCB for the 100-pin, 0.8 mm pitch card-edge connector of the B-TCA test card adapter, with the DUT soldered directly to the marked pads. Signal line contact resistance is 2 mΩ typ. with under 1 mΩ repeatability, and the connection is rated for 1,000 mating cycles. Wear gloves when breaking cards off and remove any sharp edges. Clean the contacts, then push the card straight down at its centre with under 2° of tilt.

Specifications

Order number P0011464
Measurement setup Series-Thru (two-port impedance)
Test card colour Red
DUT connection Between signal and CH2 pads in the signal line
Best-suited impedance range 1 kΩ to 1 MΩ (impedance magnitude)
Max. recommended DUT size ≈ 9 mm contact to contact
Calibrator references Open, Short (Thru), Load (50 Ω ±0.1%)
Short-Delay Time 0 ps
Recommended frequency range DC to 450 MHz (B-TCA)
Card thickness 1.57 mm (nominal)
Card-edge connector 100 pins, 0.8 mm pitch
Signal line contact resistance (4 pins) 2 mΩ typ., < 1 mΩ repeatability typ.
Test card ground contact resistance < 0.5 mΩ typ., < 100 µΩ repeatability typ.
Test card mating cycles 1,000
Max. voltage and current (B-TCA) 60 V DC, 30 V AC, 1 A
Fits B-TCA test card adapter (P0009653)
Compatible analysers Bode 100, Bode 500 (via the B-TCA)

Limitations

  • These are replacement parts for the B-TCA test card adapter. The adapter and the Bode 100 or Bode 500 analyser are not included.
  • B-TCA limits are 60 V DC or 30 V AC, 1 A, and under 350 mJ stored in an inductive DUT. Use only DC sources isolated from mains.
  • The B-TCA has no internal bias-T. Above 3.3 V DC, OMICRON Lab suggests an external bias-T between the analyser and the adapter.
  • Sensitivity degrades below 1 kΩ. For 1 mΩ to 100 Ω choose the Shunt-Thru set; for 500 mΩ to 10 kΩ on a single port, the One-Port set.

B-TCA Test Card Set Comparison

Feature B-TCA adapter Shunt-Thru set Series-Thru set One-Port set Shunt-Thru with Rs set
Order number P0009653 P0011462 P0011464 P0011465 P0011466
Contents Adapter, 2 N-N and 2 N-BNC cables, 4 calibrators, 32 test cards (8 per setup) 32 test cards, 1 calibrator 32 test cards, 1 calibrator 32 test cards, 1 calibrator 32 test cards, 1 calibrator
Test card colour All four Blue Red Black Green
Best-suited impedance range Milliohms to megohms across four setups 1 mΩ to 100 Ω 1 kΩ to 1 MΩ 500 mΩ to 10 kΩ Set by Rs: 1 mΩ to 100 Ω (0 Ω) up to 20 mΩ to 4,500 Ω (950 Ω)
Max. recommended DUT size Per setup ≈ 9 mm contact to contact, 10 mm wide ≈ 9 mm contact to contact 15 mm contact to contact ≈ 9 mm x 9 mm
Short-Delay Time Per setup 23 ps 0 ps 0 ps 23 ps
Price €1.191,95 €219,95 €206,95 €219,95 €219,95

Typical Applications

Impedance against frequency, up to 450 MHz, of SMD parts whose impedance magnitude sits between 1 kΩ and 1 MΩ. High-impedance measurements beyond the 10 kΩ upper limit of the One-Port setup.

This set suits engineers who already run a B-TCA and have used up the eight Series-Thru cards supplied with it.

What's Included

  • 32 Series-Thru test cards (4 × 8)
  • 1 Series-Thru calibrator

The OMICRON Lab Test Card Set - Series-Thru is €206,95 ex VAT. If you do not have the adapter yet, the B-TCA ships with eight cards and a calibrator per setup; contact us for a formal quotation.

Frequently Asked Questions

Which Setup Should I Use Below 1 kΩ?

Shunt-Thru for 1 mΩ to 100 Ω, or One-Port for 500 mΩ to 10 kΩ. OMICRON Lab rates Series-Thru worst of the four setups for low impedance, because the 50 Ω termination and source impedance limit its sensitivity there.

Answered by John Legg, Director, Debug Store

Can I Calibrate the Series-Thru Setup With a Thru Only?

Yes, using the Short element of the calibrator as the Thru. OMICRON Lab prefers a full Open, Short and Load calibration, because a Thru-only calibration does not remove impedance mismatch errors.

Answered by John Legg, Director, Debug Store

Last reviewed: 18 November 2026

Sources (1 manufacturer page, 1 user manual)
Ordering information
Part number (SKU)P0011464
ManufacturerOMICRON-Lab
EAN5055383604074
Warranty12 months
Shipping weight1.0 kg
  • 1 ×Calibrator for Series-Thru
  • 32 ×Series-Thru test card
Engineer Q&A

Questions and Answers

No questions have been asked about this product yet. Ask our engineers below and we'll reply by email.

Can't find your answer? Ask our engineers.

Ask a Question

Ask Our Engineers About This Product

Your question goes to the Debug Store technical team. We answer by email, and useful questions may be added to this page without your name or email address.

We reply within 24 hours.