Mikroelektronika d.o.o.
LED-Treiber 17 Click-Platine
LED-Treiber 17 Click-Platine
Verfügbarkeit für Abholungen konnte nicht geladen werden
Key Features
- Buck-Mode-LED-Treiber, 500 mA, PWM-Dimmung, breite Eingangsspannungsversorgung, Ausgangsspannung geeignet für 16-V-Hochleistungs-LEDs, Schutzfunktionen, einstellbare Schaltfrequenz, Fehlererkennung und -anzeige und mehr
- Basierend auf dem LTR3755 - DC/DC-Controller von Analog Devices
- Kann für Anwendungen verwendet werden, die eine hohe Leistungsabgabe erfordern, wie etwa gewerbliche und industrielle Beleuchtung
- mikroBUS: PWM-Schnittstelle
Overview
Einführung des LED-Treibers 17 Click Board™ – die ultimative Lösung zur LED-Steuerung
Entdecken Sie das LED Driver 17 Click Board™, eine kompakte und vielseitige Zusatzplatine, die eine einfache und dennoch leistungsstarke Lösung zur Steuerung mehrerer LEDs in verschiedenen Anwendungen bietet. Egal, ob Sie an Architekturbeleuchtung oder Allgemeinbeleuchtung arbeiten oder einfach nur Ihre Kreativität mit LEDs ausleben, dies ist die perfekte Wahl für Sie!
Mit dem LTR3755 – einem hocheffizienten DC/DC-Controller von Analog Devices
Das Herzstück dieser bemerkenswerten Platine ist der LTR3755, ein hocheffizienter DC/DC-Controller, der als Konstantstromquelle fungiert. Mit der Fähigkeit, Hochstrom-LEDs und integrierte externe Low-Side-N-Kanal-Leistungs-MOSFETs problemlos anzusteuern, gewährleistet das LED Driver 17 Click Board™ einen stabilen Betrieb über einen weiten Versorgungsspannungsbereich.
Umfassende LED-Schutzfunktionen
Das LED Driver 17 Click Board™ wurde mit Blick auf die Benutzersicherheit entwickelt und bietet mehrere wichtige Schutzfunktionen für Ihre LEDs, einschließlich Überspannungs- und Überstromschutz. Darüber hinaus können Sie mit dem Frequenzanpassungsstift die Schaltfrequenz von 100 kHz bis 1 MHz programmieren und so Effizienz und Leistung entsprechend Ihren Anforderungen optimieren.
Unterstützt durch mikroSDK – Vereinfachung der Softwareentwicklung
Wenn es um Softwareentwicklung geht, sind Sie mit dem LED Driver 17 Click Board™ bestens bedient. Es wird von einer mikroSDK-kompatiblen Bibliothek unterstützt, die Funktionen enthält, die die Softwareentwicklung zum Kinderspiel machen. Dieses Click Board™ ist ein vollständig getestetes Produkt und kann in jedes System integriert werden, das mit der mikroBUS™-Buchse ausgestattet ist.
Eine vielseitige Wahl für Hobbyisten und Profis
Egal, ob Sie Hobbyist oder Profi sind, das LED Driver 17 Click Board™ ist die ideale Wahl für die Steuerung mehrerer LEDs in verschiedenen Einstellungen. Mit seinen umfassenden Funktionen, seiner Benutzerfreundlichkeit und seiner zuverlässigen Leistung wird dieses Click Board™ Ihre LED-Projekte und -Anwendungen zweifellos verbessern.
How Does The LED Driver 17 Click Board™ Work?
The LED Driver 17 Click Board™ is based on the LT3755, a highly efficient DC/DC controller from Analog Devices. This Click board™ is designed as a Buck mode LED driver with the ability to output 500mA, offering, in addition, PWM dimming functionality. The LTR3755, a highly efficient DC/DC controller, operates as a constant-current source, features onboard low-side external N-channel power MOSFETs, which are driven from an internal regulated supply, and it is capable of driving high-power 16V LEDs. Due to its high efficiency and reliable protection features, this board can be used in applications that require consistent and precise LED lighting control. It can also be used in applications that demand high power output, such as commercial and industrial lighting.
In terms of connectivity, this solution is designed to be controlled via the PWM pin of the mikroBUS™ socket to provide LED dimming control with ratios of up to 3000:1. In addition, the LT3755 also has a frequency adjust pin that allows the user to program the switching frequency from 100kHz to 1MHz. This feature is performed via an onboard R5 resistor, with the 800kHz set as the default value to optimize efficiency and performance.
Besides the PWM pin, this Click board™ also features a fault pin labelled FLT, which is routed to the default interrupt INT position of the mikroBUS™ socket. This fault pin indicates any fault conditions to an external system, including overvoltage and overcurrent protection. Besides information via the mikroBUS™ socket, the fault signal is visually indicated via a red LED labelled LD2. This LED Driver 17 Click supports an external power supply for the driver, which can be connected to the input terminal labelled VIN and should be within the range of 22V to 36V.
The LED Driver 17 Click Board™ can operate with either 3.3V or 5V logic voltage levels selected via the VCC SEL jumper. This way, both 3.3V and 5V capable MCUs can use the communication lines properly. However, the Click board™ comes equipped with a library containing easy-to-use functions and an example code that can be used, as a reference, for further development.
SPECIFICATIONS
| Type | LED Drivers |
| Applications | It can be used for applications that demand high power output, such as commercial and industrial lighting |
| On-board modules | LTR3755 - DC/DC controller from Analog Devices |
| Key Features | Buck mode LED driver, 500mA, PWM dimming, wide input voltage supply, output voltage suitable for 16V high power LEDs, protection features, adjustable switching frequency, fault detection and indication, and more |
| Interface | PWM |
| Compatibility | mikroBUS |
| Click board size | L (57.15 x 25.4 mm) |
| Input Voltage | 3.3V or 5V |
PINOUT DIAGRAM
This table shows how the LED Driver 17 Click Board™ pinout corresponds to the pinout on the mikroBUS™ socket (the latter is shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| NC | 1 | AN | PWM | 16 | PWM | PWM Signal | |
| NC | 2 | RST | INT | 15 | FLT | Fault Signal | |
| NC | 3 | CS | RX | 14 | NC | ||
| NC | 4 | SCK | TX | 13 | NC | ||
| NC | 5 | MISO | SCL | 12 | NC | ||
| NC | 6 | MOSI | SDA | 11 | NC | ||
| Power Supply | 3.3V | 7 | 3.3V | 5V | 10 | 5V | Power Supply |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
ONBOARD SETTINGS AND INDICATORS
| Label | Name | Default | Description |
|---|---|---|---|
| LD1 | PWR | - | Power LED Indicator |
| LD2 | LD2 | - | Fault LED Indicator |
| JP1 | VCC SEL | Left | Logic Level Voltage Selection 3V3/5V: Left position 3V3, Right position 5V |
LED DRIVER 17 CLICK ELECTRICAL SPECIFICATIONS
| Description | Min | Typ | Max | Unit |
|---|---|---|---|---|
| Supply Voltage | 3.3 | - | 5 | V |
| Input Voltage Range | 22 | - | 36 | V |
| Output Current | - | 500 | - | mA |
Software Support
We provide a library for the LED Driver 17 Click Board™ and a demo application (example), developed using MIKROE compilers. The demo can run on all the main MIKROE development boards.
The package can be downloaded/installed directly from NECTO Studio The package Manager (recommended), downloaded from our LibStock™ or found on the MikroE Github account.
Library Description
This library contains API for the LED Driver 17 Click Board™ driver.
Key functions
-
leddriver17_get_fault_pinThis function returns the fault (FLT) pin logic state. -
leddriver17_set_duty_cycleThis function sets the PWM duty cycle in percentages ( Range[ 0..1 ] ).
Example Description
This example demonstrates the use of LED Driver 17 Click board™ by changing the LED dimming level.
void application_task ( void )
{
static int8_t duty_cnt = 1;
static int8_t duty_inc = 1;
float duty = duty_cnt / 10.0;
if ( !leddriver17_get_fault_pin ( &leddriver17 ) )
{
log_printf( &logger, " Fault detected!rn" );
}
leddriver17_set_duty_cycle ( &leddriver17, duty );
log_printf( &logger, " Duty: %u%%rnn", ( uint16_t ) ( duty_cnt * 10 ) );
Delay_ms( 500 );
if ( 10 == duty_cnt )
{
duty_inc = -1;
}
else if ( 0 == duty_cnt )
{
duty_inc = 1;
}
duty_cnt += duty_inc;
}
The full application code, and ready to use projects can be installed directly from NECTO Studio The package Manager (recommended), downloaded from our LibStock™ or found on MikroE Github account.
Other MikroE Libraries used in the example:
- MikroSDK.Board
- MikroSDK.Log
- Click.LEDDriver17
Additional Notes and Information
Depending on the development board you are using, you may need USB UART Click Board™, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MIKROE compilers.
MIKROSDK
The LED Driver 17 Click Board™ is supported with the mikroSDK - MIKROE Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Software Support
We provide a library for the LED Driver 17 Click Board™ and a demo application (example), developed using MIKROE compilers. The demo can run on all the main MIKROE development boards.
The package can be downloaded/installed directly from NECTO Studio The package Manager (recommended), downloaded from our LibStock™ or found on the MikroE Github account.
Library Description
This library contains API for the LED Driver 17 Click Board™ driver.
Key functions
-
leddriver17_get_fault_pinThis function returns the fault (FLT) pin logic state. -
leddriver17_set_duty_cycleThis function sets the PWM duty cycle in percentages ( Range[ 0..1 ] ).
Example Description
This example demonstrates the use of LED Driver 17 Click board™ by changing the LED dimming level.
void application_task ( void )
{
static int8_t duty_cnt = 1;
static int8_t duty_inc = 1;
float duty = duty_cnt / 10.0;
if ( !leddriver17_get_fault_pin ( &leddriver17 ) )
{
log_printf( &logger, " Fault detected!rn" );
}
leddriver17_set_duty_cycle ( &leddriver17, duty );
log_printf( &logger, " Duty: %u%%rnn", ( uint16_t ) ( duty_cnt * 10 ) );
Delay_ms( 500 );
if ( 10 == duty_cnt )
{
duty_inc = -1;
}
else if ( 0 == duty_cnt )
{
duty_inc = 1;
}
duty_cnt += duty_inc;
}
The full application code, and ready to use projects can be installed directly from NECTO Studio The package Manager (recommended), downloaded from our LibStock™ or found on MikroE Github account.
Other MikroE Libraries used in the example:
- MikroSDK.Board
- MikroSDK.Log
- Click.LEDDriver17
Additional Notes and Information
Depending on the development board you are using, you may need USB UART Click Board™, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MIKROE compilers.
MIKROSDK
The LED Driver 17 Click Board™ is supported with the mikroSDK - MIKROE Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.