Mikroelektronika d.o.o.
DIGI POT 11 Click-Platine
DIGI POT 11 Click-Platine
Verfügbarkeit für Abholungen konnte nicht geladen werden
Key Features:
- Doppelte Dualpotentiometer, 256 lineare Taper-Positionen, einzelne 3,3-V-Versorgung, geringer Stromverbrauch, 50 kΩ End-to-End-Widerstand, I2C-Schnittstelle, Power-On stellt den Wischer auf Mittelskala ein und mehr
- Basierend auf dem MAX5387 – duales, flüchtiges, lineares digitales Potentiometer von Analog Devices
- Kann als Ersatz für ein mechanisches Potentiometer für den tragbaren Verbrauchermarkt und für batteriegestützte Industrieanwendungen verwendet werden
- mikroBUS: I2C-Schnittstelle
Das DIGI POT 11 Click Board™ ist eine kompakte Zusatzplatine, die ein digital gesteuertes Potentiometer darstellt. Diese Platine verfügt über ein Doppelpack des MAX5387, ein duales, flüchtiges, lineares digitales Potentiometer mit 256 Abgriffen und niedriger Spannung von Analog Devices. Auf diese Weise werden vier digital I2C-gesteuerte Potentiometer mit durchgehenden Widerstandswerten von 50 kΩ realisiert. Dieses Gerät wird mit einer einzelnen +3,3-V-Stromversorgung betrieben und bietet einen niedrigen durchgehenden Temperaturkoeffizienten von 35 ppm/ºC. Dieses Click Board™ kann als mechanischer Potentiometerersatz für den tragbaren Verbrauchermarkt und industrielle Anwendungen mit Batterie-Backup verwendet werden.
Das DIGI POT 11 Click Board™ wird von einer mikroSDK-kompatiblen Bibliothek unterstützt, die Funktionen enthält, die die Softwareentwicklung vereinfachen. Dieses Click Board™ ist ein gründlich getestetes Produkt und kann auf einem System verwendet werden, das mit der mikroBUS™-Buchse ausgestattet ist.
How Does The DIGI POT 11 Click Board™ Work?
The DIGI POT 11 Click Board™ is based on dual MAX5387, a dual volatile, low-voltage linear taper digital potentiometers from Analog Devices, with four digitally controlled potentiometers, are realized with end-to-end resistance values of 50kΩ. The potentiometers consist of 255 fixed resistors in series between appropriate H and L terminals, providing a low 35ppm/ºC end-to-end temperature coefficient. The potentiometer wiper (W) terminals are programmable to access any one of the 256 tap points on the resistor string.
The DIGI POT 11 Click Board™ communicates with MCU using the standard I2C 2-Wire interface with a maximum clock frequency of 400kHz. The potentiometers are programmable independently of each other. The MAX5387 has a 7-bit slave address with the first five MSBs fixed to 01010. The address pins A0 and A1 of both potentiometers are programmed by the user and determine the value of the last three LSBs of the slave address, which can be selected by positioning onboard SMD jumpers labelled as ADDR SEL, in U1 or U2 part, to an appropriate position marked as 0 or 1.
The I2C interface contains a shift register that decodes the command and addresses bytes, routing the data to the appropriate control registers. Data written to a control register immediately updates the wiper position. In the beginning, wipers A and B always power up in mid-position.
The DIGI POT 11 Click Board™ can be operated only with a 3.3V logic voltage level. The board must perform appropriate logic voltage level conversion before using MCUs with different logic levels. However, the Click board™ comes equipped with a library containing functions and an example code that can be used, as a reference, for further development.
SPECIFICATIONS
| Type | Digital potentiometer |
| Applications | Can be used as a mechanical potentiometer replacement for the portable consumer market and battery-backup industrial applications |
| On-board modules | MAX5387 - dual volatile linear taper digital potentiometer from Analog Devices |
| Key Features | Double dual potentiometers, 256-tap linear taper positions, single 3.3V supply, low power consumption, 50kΩ end-to-end resistance, I2C interface, Power-On sets wiper to midscale, and more |
| Interface | I2C |
| Compatibility | mikroBUS |
| Click board size | M (42.9 x 25.4 mm) |
| Input Voltage | 3.3V |
PINOUT DIAGRAM
This table shows how the pinout of the DIGI POT 11 Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| NC | 1 | AN | PWM | 16 | NC | ||
| NC | 2 | RST | INT | 15 | NC | ||
| NC | 3 | CS | RX | 14 | NC | ||
| NC | 4 | SCK | TX | 13 | NC | ||
| NC | 5 | MISO | SCL | 12 | SCL | I2C Clock | |
| NC | 6 | MOSI | SDA | 11 | SDA | I2C Data | |
| Power Supply | 3.3V | 7 | 3.3V | 5V | 10 | NC | |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
ONBOARD SETTINGS AND INDICATORS
| Label | Name | Default | Description |
|---|---|---|---|
| LD1 | PWR | - | Power LED Indicator |
| JP1-JP4 | ADDR SEL | Left | I2C Address Selection 0/1: Left position 0, Right position 1 |
| J1-J4 | U1-U2 | Populated | DIGI POT Header Terminals |
DIGI POT 11 CLICK ELECTRICAL SPECIFICATIONS
| Description | Min | Typ | Max | Unit |
|---|---|---|---|---|
| Supply Voltage | - | 3.3 | - | V |
| End-to-end Resistance | - | - | 50 | kΩ |
| Number of Steps | - | - | 256 | step |
| Operating Temperature Range | -40 | +25 | +120 | °C |
Software Support
We provide a library for the DIGI POT 11 Click Board™ as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
The package can be downloaded/installed directly from NECTO Studio The package Manager (recommended), downloaded from our LibStock™ or found on the MikroE Github account.
Library Description
This library contains API for the DIGI POT 11 Click Board™ driver.
Key functions
-
digipot11_set_u1_wiperThis function sets the position of the selected wiper of U1 device by using an I2C serial interface. -
digipot11_set_u2_wiperThis function sets the position of the selected wiper of U2 device by using an I2C serial interface.
Example Description
This example demonstrates the use of the DIGI POT 11 Click Board™ by changing the wipers position of both U1 and U2 devices.
void application_task ( void )
{
for ( uint16_t wiper_pos = DIGIPOT11_WIPER_ZERO_SCALE; wiper_pos <= DIGIPOT11_WIPER_FULL_SCALE; wiper_pos += 5 )
{
if ( DIGIPOT11_OK == digipot11_set_u1_wiper ( &digipot11, DIGIPOT11_WIPER_SEL_BOTH, ( uint8_t ) wiper_pos ) )
{
log_printf( &logger, " U1 wipers position: %urn", wiper_pos );
}
if ( DIGIPOT11_OK == digipot11_set_u2_wiper ( &digipot11, DIGIPOT11_WIPER_SEL_BOTH,
( uint8_t ) ( DIGIPOT11_WIPER_FULL_SCALE - wiper_pos ) ) )
{
log_printf( &logger, " U2 wipers position: %urnn", ( DIGIPOT11_WIPER_FULL_SCALE - wiper_pos ) );
}
Delay_ms( 1000 );
}
}
The complete application code and ready-to-use projects can be installed directly from NECTO Studio. The package Manager (recommended), is downloaded from our LibStock™ or found on the MikroE Github account.
Other MikroE Libraries used in the example:
- MikroSDK.Board
- MikroSDK.Log
- Click.DIGIPOT11
Additional Notes and Information
Depending on the development board you are using, you may need USB UART Click Board™, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MikroElektronika compilers.
MIKROSDK
The DIGI POT 11 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
DIGI POT 11 Click-Platine
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.