Mikroelektronika d.o.o.
Motion 3 Klick-Board
Motion 3 Klick-Board
Verfügbarkeit für Abholungen konnte nicht geladen werden
Der Motion 3 Click Board™ basiert auf EKMC1606112, einem PIR-Bewegungssensor von Panasonic Corporation, der als Bewegungsmelder für Menschen verwendet wird. Ebenfalls auf dem Motion 3 Click Board™ enthalten ist das TLP241A-Fotorelais von Toshiba, das für eine verstärkte galvanische Trennung der externen Signale sorgt, die zum Ansteuern einiger externer elektronischer Hochleistungsgeräte bei Bewegungserkennung verwendet werden. Dank eines sehr geringen Widerstands im eingeschalteten Zustand sind im ausgeschalteten Zustand bis zu 40 V zwischen den SSR-Kontakten und im eingeschalteten Zustand Ströme von bis zu 2 A möglich.
Das Motion 3 Click Board™ wird von einer mikroSDK-kompatiblen Bibliothek unterstützt, die Funktionen enthält, die die Softwareentwicklung vereinfachen. Dieses Click Board™ wird als vollständig getestetes Produkt geliefert und ist bereit für den Einsatz auf einem System, das mit der mikroBUS™-Buchse ausgestattet ist.
How Does The Motion 3 Click Board™ Work?
The Motion 3 Click Board™ is using a PIR sensor that can detect changes in the amount of infrared radiation impinging upon it, which varies depending on the temperature and surface characteristics of the objects in front of the sensor. Detection performance of EKMC1606112 at ambient temperature of 25℃ with temperature difference of 8℃ is up to 17m and for temperature difference of 4℃ it's up to 12m. Angle detection area with 128 detection zones is 62°（±31°）horizontal and 62°（±31°）vertical.
Output from PIR sensor is feed into buffer and then photo-relay allowing users to directly control with galvanic isolation from sensor and MCU electronic devices such as lights, motors, gates etc. The TLP241A photo-relay is able to effectively replace traditionally used mechanical relays, bringing up the full set of inherited benefits: virtually unlimited number of cycles since there are no moving parts that would wear off, no bouncing effect on the output contacts, high resistance to mechanical shock and environmental influence, low current required for the activation, constant resistance since no carbon and rust can build up on contacts, there is no sparking or electric arc forming while operated, compact size, higher isolation voltage, and so on.
When an object, such as a person, passes in front of the background, such as a wall, the temperature at that point in the sensor's field of view will rise from room temperature to body temperature, and then back again. The sensor converts the resulting change in the incoming infrared radiation into a change in the output voltage, and this triggers the detection. Objects of similar temperature but different surface characteristics may also have a different infrared emission pattern, and thus moving them with respect to the background may trigger the detector as well. In some cases, going back and forth towards the sensor (parallel movement to the axis Z), may not be detected.
Difficulty in sensing the heat source is that glass, acrylic or similar materials standing between the target and the sensor may not allow a correct transmission of infrared rays and also non-movement or quick movements of the heat source inside the detection area.
SPECIFICATIONS
| Type | Motion |
| Applications | Alarm systems, light switch controllers, automatic doors and similar systems where human presence needs to be detected. |
| On-board modules | EKMC1606112 the PIR motion sensor |
| Key Features | 128 detection zones, wide detection range and maximum range between 12 and 17 m |
| Interface | GPIO |
| Compatibility | mikroBUS |
| Click board size | M (42.9 x 25.4 mm) |
| Input Voltage | 3.3V or 5V |
PINOUT DIAGRAM
This table shows how the pinout of the Motion 3 Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| NC | 1 | AN | PWM | 16 | NC | ||
| NC | 2 | RST | INT | 15 | INT | Interrupt | |
| Enable | EN | 3 | CS | RX | 14 | NC | |
| NC | 4 | SCK | TX | 13 | NC | ||
| NC | 5 | MISO | SCL | 12 | NC | ||
| NC | 6 | MOSI | SDA | 11 | NC | ||
| Power Supply | 3.3V | 7 | 3.3V | 5V | 10 | 5V | Power Supply |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
ONBOARD SETTINGS AND INDICATORS
| Label | Name | Default | Description |
|---|---|---|---|
| PWR | LD1 | - | Power LED Indicator |
| ON | LD2 | - | Photorelay ON Indicator |
| JP1 | VCC SEL | Left | Logic voltage level selection: left position 3.3V, right position 5V |
DETECTION PERFORMANCE AND ELECTRICAL CHARACTERISTICS
| Temperature Difference | Value | |
|---|---|---|
| Detection Range | 8℃ | up to 17m |
| 4℃ | up to 12m | |
| Detection Area | Detection Angle | Value |
| Horizontal | 62°（±31°) | |
| Vertical | 62°（±31°) | |
| Detection Zones | 128 | |
| Photorelay Characteristics | Maximum Voltage | Maximum Current |
| 40V | 2A |
Software Support
We provide a library for the Motion 3 Click Board™ on our LibStock page, as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Library Description
Library provides functions for controlling en pin, and getting int pin state.
Key Functions
void motion3_set_en_pin ( uint8_t state )- Function for setting en pin stateuint8_t motion3_get_int ( void )- Function for getting int pin state
Example Description
The application is composed of three sections :
- System Initialization - Initialization of pins
- Application Initialization - Maps pins and enables device
- Application Task - Waiting for motion to be detected
void application_task ( ) { uint8_t int_status; int_status = motion3_get_int(); if ( int_status != MOTION3_INTERRUPT_NOT_DETECT ) { mikrobus_logWrite( "Motion detected", _LOG_LINE ); while ( int_status != MOTION3_INTERRUPT_NOT_DETECT ) { int_status = motion3_get_int(); } mikrobus_logWrite( "Motion wait", _LOG_LINE ); } }
The full application code, and ready to use projects can be found on our LibStock page.
Other mikroE Libraries used in the example:
- UART
Additional Notes and Information
Depending on the development board you are using, you may need USB UART click, USB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.
MIKROSDK
The Motion 3 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
Motion 3 Klick-Board
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.