Mikroelektronika d.o.o.
UART MUX Click-Platine
UART MUX Click-Platine
Verfügbarkeit für Abholungen konnte nicht geladen werden
Das UART MUX Click Board™ schaltet die UART-Pins (RX und TX) vom mikroBUS™ auf einen der vier verfügbaren Ausgänge. Es verwendet den SN74LV4052A, einen dualen 4-Kanal-Multiplexer und Demultiplexer von Texas Instruments. Es ist für den VCC-Betrieb von 2 V bis 5,5 V ausgelegt. Einige der typischen Anwendungen für das SN74LV4052A umfassen Signalgating, Chopping, Modulation oder Demodulation (Modem) und Signalmultiplexing für Analog-Digital- und Digital-Analog-Konvertierungssysteme, was es ideal für das Multiplexen der UART-Pins vom mikroBUS™ auf die mehreren Ausgänge macht.
How Does The UART Mux Click Board™ Work?
The UART MUX Click Board™ is equipped with the SN74LV4052A, a Dual 4-Channel Multiplexer and Demultiplexer, from Texas Instruments. Two control pins are used to switch to one of four available outputs, from a single UART input, from the mikroBUS. Control pins labelled as A and B, are routed to the mikroBUS and can be operated by both 3.3V and 5V MCUs. The fourth control pin is labelled as EN pin, and it is used to enable the internal multiplexing switches of the IC, when is set to a HIGH logic level (it is active HIGH). A and B pins are routed to CS and PWM pins of the mikroBUS respectively. The active low Inhibit (INH) tri-state all the channels when high and when low, depending on the A and B inputs, one of the four independent input/outputs is connected to the UART communication pins. INH pin is routed to the RST pin on the mikroBUS.
The ultra-low leakage current ensures that there is no signal interference from the inputs that are not selected by the A and B pins. A low crosstalk also ensures that the signal on one channel remains clean of interferences caused by other channels. This ensures a reliable operation of the IC and the Click Board™ itself.
The output signals can be connected via the 2x4 pin headers. Besides RX and TX pins, every output also has dedicated VCC and GND pins available, so that user can easily route multiple devices with this Click Board™. Independent power supply input allows the user to work with a wide range of signal amplitudes, depending on the application requirements, as long as the power supply stays within the limits.
More information about the SN74LV4052A can be found in the attached datasheet. However, the Click Board™ comes equipped with a library that contains easy to use functions and a usage example that may be used as a reference for the development.
The UART MUX Click Board™ offers a selection between 3.3V and 5V operation, with the onboard SMD jumper, labelled as PWR SEL. This allows both 3.3V and 5V MCUs to be interfaced with this Click Board™.
SPECIFICATIONS
| Type | DAC |
| Applications | Telecomunications, Infotainment, Signal Gating and Isolation, Home Appliances, Programmable Logic Circuits, Modulation and Demodulation |
| On-board modules | SN74LV4052A, a Dual 4-Channel Analog Multiplexer and Demultiplexer from Texas Instruments |
| Key Features | High On-Off Output-Voltage Ratio, Extremely Low Input Current, 2-V to 5.5-V VCC Operation |
| Interface | GPIO,UART |
| Compatibility | mikroBUS |
| Click Board™ size | L (57.15 x 25.4 mm) |
| Input Voltage | 3.3V or 5V |
PINOUT DIAGRAM
This table shows how the pinout of the UART MUX Click Board™ corresponds to the pinout on the mikroBUS socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| NC | 1 | AN | PWM | 16 | B | Control Pin B | |
| Inhibit Input | INH | 2 | RST | INT | 15 | NC | |
| Control Pin A | A | 3 | CS | RX | 14 | TX | UART Transmit |
| NC | 4 | SCK | TX | 13 | RX | UART Receive | |
| NC | 5 | MISO | SCL | 12 | NC | ||
| NC | 6 | MOSI | SDA | 11 | NC | ||
| Power Supply | 3.3V | 7 | 3.3V | 5V | 10 | 5V | Power Supply |
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
ONBOARD SETTINGS AND INDICATORS
| Label | Name | Default | Description |
|---|---|---|---|
| PWR | PWR | - | Power LED Indicator |
| J1 | VCC SEL | Left | Power supply voltage selection: left position 3.3V, right position 5V |
Software Support
We provide a library for the UART MUX Click Board™ on our LibStock page, as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.
Library Description
The library covers all the necessary functions that enables the usage of the UART MUX Click Board™. User can write, read or check if there is a new byte received on all four channels that are available. Library also offers the functions taht allow user to inhibit or uninhibit the communication.
Key Functions
void uartmux_writeByte(uint8_t input)- Writes sinle byteuint8_t uartmux_readByte()- Read received byteuint8_t uartmux_byteReady()- Checks is there a new byte received
Example Description
The application is composed of three sections :
- System Initialization - Initializes UART, GPIO and LOG structures, sets RST, CS and PWM pins as output.
- Application Initialization - Initalizes UART driver, uninhibites communication and makes an initial log.
- Application Task - (code snippet) This example demonstrates the use of UART Mux Click Board™ by eather sending or receiving the message on channel one of the device.
void applicationTask()
{
char tmp;
// RECEIVER - UART polling
/*
if ( 1 == uartmux_byteReadyChann1() )
{
tmp = uartmux_readByteChann1();
mikroBUS_logWrite( &tmp, _LOG_BYTE );
}
*/
// TRANSMITTER - TX each 2 sec
for (tmp = 0; tmp < 9; tmp++)
{
uartmux_writeByteChann1( MESSAGE_DATA[tmp] );
}
Delay_ms(2000);
}
The full application code, and ready to use projects can be found on our LibStock page.
Other mikroE Libraries used in the example:
- UART
- Conversions
Additional Notes and Information
Depending on the development board you are using, you may need a USB UART Click Board™, USB UART 2 Click Board™ or RS232 Click Board™ to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.
MIKROSDK
The UART MUX Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click Board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.
UART MUX Click-Platine
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.