Mikroelektronika d.o.o.
Boost 4 Klicken Sie auf Board
Boost 4 Klicken Sie auf Board
Verfügbarkeit für Abholungen konnte nicht geladen werden
Overview
Das Boost 4 Click Board™ verfügt über den TPS61230A, einen hocheffizienten, vollständig integrierten synchronen Aufwärtswandler von Texas Instruments. Das Click Board™ ist für den Betrieb mit einer 3,3-V-Stromversorgung ausgelegt.
Das Boost 4 Click Board™ steuert den Zielchip über den Digipot, der über SPI-Kommunikation mit dem Mikrocontroller des Systems verfügt.
The Boost 4 Click Board™ carries the TPS61230A, a high efficiency fully integrated synchronous boost converter from Texas Instruments. The click is designed to run on a 3.3V power supply. Boost 4 click drives the target chip through the digi pot, which has SPI communication with the microcontroller on the system.
Boost 4 click is the power management solution for your next project.
How Does The oost 4 Click Board™ Work?
The Boost 4 Click Board™ provides an adjustable output voltage through the SPI DAC, that drives the FB pin to set desired voltage. The click is capable of delivering up to 2.4-A output current at a 5V output with the 2.5-V input supply.
TPS61230A FEATURES
The TPS61230A device is a high efficiency fully integrated synchronous boost converter. It integrates 6-A, 21-mΩ and 18-mΩ power switches.
During the light load condition, the TPS61230A automatically enters into the PFM operation for maximizing the efficiency with the lowest quiescent current. In the shutdown by pulling EN pin to the logic low, the load is completely disconnected from the input, and the input current consumption is reduced to below 1.0 μA.
SPECIFICATIONS
| Type | Boost |
| Applications | Battery powered products, battery backup units, etc. |
| On-board modules | TPS61230A, a high efficiency fully integrated synchronous boost converter from Texas Instruments |
| Key Features | Input Voltage Range: 2.5 V to 4.5 V, output Voltage Range: 2.5 V to 5.5 V |
| Interface | SPI |
| Compatibility | mikroBUS |
| Click board size | M (42.9 x 25.4 mm) |
| Input Voltage | 3.3V |
Pinout Diagram
This table shows how the pinout of the Boost 4 Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).
| Notes | Pin |  |
Pin | Notes | |||
|---|---|---|---|---|---|---|---|
| NC | 1 | AN | PWM | 16 | NC | ||
| Enable pin | EN | 2 | RST | INT | 15 | NC | |
| Chip select | CS | 3 | CS | TX | 14 | NC | |
| SPI clock | SCK | 4 | SCK | RX | 13 | NC | |
| SDO | 5 | MISO | SCL | 12 | NC | ||
| Slave data in for SPI | SDI | 6 | MOSI | SDA | 11 | NC | |
| NC | 7 | 3.3V | 5V | 10 | NC | ||
| Ground | GND | 8 | GND | GND | 9 | GND | Ground |
Software Support
Code examples for the Boost 4 Click Board™, written for MikroElektronika hardware and compilers are available on Libstock.
CODE SNIPPET
The following code snippet shows how to cycle through different output voltages.
01 void main()
02 {
03 systemInit();
04
05 while (1)
06 {
07 delay_ms(3000);
08 //Sets the voltage to VOUTmax, ~5.25 V
09 CS_PIN = 0; //Sets chip select to active
10 Spi3_Write(0b01110000);
11 Spi3_Write(0b00000000);
12 CS_PIN = 1; //Sets chip select to inactive
13
14 delay_ms(3000);
15 //Sets the voltage to VOUTmin, which depends on VIN, but cannot
16 //be lower than 2.50 V
17 CS_PIN = 0; //Sets chip select to active
18 Spi3_Write(0b01111111);
19 Spi3_Write(0b11111111);
20 CS_PIN = 1; //Sets chip select to inactive
21
22 delay_ms(3000);
23 //Sets the voltage ~4.0 V
24 CS_PIN = 0; //Sets chip select to active
25 Spi3_Write(0b01110111);
26 Spi3_Write(0b01000000);
27 CS_PIN = 1; //Sets chip select to inactive
28
29 delay_ms(3000);
30 //Sets the voltage ~4.5 V
31 CS_PIN = 0; //Sets chip select to active
32 Spi3_Write(0b01110100);
33 Spi3_Write(0b00011111);
34 CS_PIN = 1; //Sets chip select to inactive
35 }
36 }
Software Support
Code examples for the Boost 4 Click Board™, written for MikroElektronika hardware and compilers are available on Libstock.
CODE SNIPPET
The following code snippet shows how to cycle through different output voltages.
01 void main()
02 {
03 systemInit();
04
05 while (1)
06 {
07 delay_ms(3000);
08 //Sets the voltage to VOUTmax, ~5.25 V
09 CS_PIN = 0; //Sets chip select to active
10 Spi3_Write(0b01110000);
11 Spi3_Write(0b00000000);
12 CS_PIN = 1; //Sets chip select to inactive
13
14 delay_ms(3000);
15 //Sets the voltage to VOUTmin, which depends on VIN, but cannot
16 //be lower than 2.50 V
17 CS_PIN = 0; //Sets chip select to active
18 Spi3_Write(0b01111111);
19 Spi3_Write(0b11111111);
20 CS_PIN = 1; //Sets chip select to inactive
21
22 delay_ms(3000);
23 //Sets the voltage ~4.0 V
24 CS_PIN = 0; //Sets chip select to active
25 Spi3_Write(0b01110111);
26 Spi3_Write(0b01000000);
27 CS_PIN = 1; //Sets chip select to inactive
28
29 delay_ms(3000);
30 //Sets the voltage ~4.5 V
31 CS_PIN = 0; //Sets chip select to active
32 Spi3_Write(0b01110100);
33 Spi3_Write(0b00011111);
34 CS_PIN = 1; //Sets chip select to inactive
35 }
36 }
Frequently Asked Questions
Have a Question?
Be the first to ask a question about this.