{"product_id":"test-card-set-shunt-thru","title":"OMICRON Lab Test Card Set - Shunt-Thru","description":"\u003cp\u003eThe OMICRON Lab Test Card Set - Shunt-Thru (P0011462) is a replacement set of 32 Shunt-Thru test cards and one Shunt-Thru calibrator for the B-TCA test card adapter. OMICRON Lab rates Shunt-Thru as the best of the four B-TCA setups for low impedance, with an optimal DUT impedance magnitude of 1 mΩ to 100 Ω, within the B-TCA's recommended DC to 450 MHz range, on a Bode 500 (10 mHz to 450 MHz) or Bode 100 (1 Hz to 50 MHz) vector network analyser. Order it to restock the blue Shunt-Thru cards when you characterise low-impedance passive SMD components.\u003c\/p\u003e\n\n\u003ch2\u003eShunt-Thru Impedance Measurement From 1 mΩ to 100 Ω\u003c\/h2\u003e\n\u003cp\u003eOn a Shunt-Thru test card the DUT is soldered between the signal pad and the GND pad, so it shunts the signal line to ground. This two-port arrangement gives the best low-impedance sensitivity of the four setups. Above 100 Ω the 50 Ω parallel path degrades sensitivity, so for high-impedance parts move to the Series-Thru set. The maximum recommended DUT size is about 9 mm from one contact to the other, with a maximum width of 10 mm.\u003c\/p\u003e\n\n\u003ch2\u003eShunt-Thru Calibrator: Open, Short and Load\u003c\/h2\u003e\n\u003cp\u003eThe blue Shunt-Thru calibrator carries Open (Thru), Short and Load references, with the Load at 50 Ω ±0.1%. In the Bode Analyzer Suite, run Open first, then Short with the Short-Delay Time set to 23 ps, then Load. A Thru-only calibration using the Open element is possible, but OMICRON Lab notes that it does not remove impedance mismatch or the low-frequency ground-loop error, so a full Open, Short and Load calibration is the one to use for low-impedance work.\u003c\/p\u003e\n\n\u003ch2\u003eSoldering and Fitting B-TCA Test Cards\u003c\/h2\u003e\n\u003cp\u003eEach test card is a 1.57 mm (nominal) PCB for the 100-pin, 0.8 mm pitch card-edge connector of the \u003ca href=\"\/it\/products\/omicron-lab-b-tca-test-card-adapter-p0009653\"\u003eB-TCA test card adapter\u003c\/a\u003e, with the DUT soldered directly to the marked pads. Signal line contact resistance is 2 mΩ typ. with under 1 mΩ repeatability, and the connection is rated for 1,000 mating cycles. Wear gloves when breaking cards off and remove any sharp edges. Clean the contacts, then push the card straight down at its centre with under 2° of tilt.\u003c\/p\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eOrder number\u003c\/th\u003e\n\u003ctd\u003eP0011462\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eMeasurement setup\u003c\/th\u003e\n\u003ctd\u003eShunt-Thru (two-port impedance)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTest card colour\u003c\/th\u003e\n\u003ctd\u003eBlue\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDUT connection\u003c\/th\u003e\n\u003ctd\u003eBetween signal and GND pads\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eBest-suited impedance range\u003c\/th\u003e\n\u003ctd\u003e1 mΩ to 100 Ω (impedance magnitude)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eMax. recommended DUT size\u003c\/th\u003e\n\u003ctd\u003e≈ 9 mm contact to contact, max. width 10 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eCalibrator references\u003c\/th\u003e\n\u003ctd\u003eOpen (Thru), Short, Load (50 Ω ±0.1%)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eShort-Delay Time\u003c\/th\u003e\n\u003ctd\u003e23 ps\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eRecommended frequency range\u003c\/th\u003e\n\u003ctd\u003eDC to 450 MHz (B-TCA)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eCard thickness\u003c\/th\u003e\n\u003ctd\u003e1.57 mm (nominal)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eCard-edge connector\u003c\/th\u003e\n\u003ctd\u003e100 pins, 0.8 mm pitch\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eSignal line contact resistance (4 pins)\u003c\/th\u003e\n\u003ctd\u003e2 mΩ typ., \u0026lt; 1 mΩ repeatability typ.\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTest card ground contact resistance\u003c\/th\u003e\n\u003ctd\u003e\u0026lt; 0.5 mΩ typ., \u0026lt; 100 µΩ repeatability typ.\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTest card mating cycles\u003c\/th\u003e\n\u003ctd\u003e1,000\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eMax. voltage and current (B-TCA)\u003c\/th\u003e\n\u003ctd\u003e60 V DC, 30 V AC, 1 A\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003eB-TCA test card adapter (P0009653)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eCompatible analysers\u003c\/th\u003e\n\u003ctd\u003eBode 100, Bode 500 (via the B-TCA)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eLimitations\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eThese are replacement parts for the \u003ca href=\"\/it\/products\/omicron-lab-b-tca-test-card-adapter-p0009653\"\u003eB-TCA test card adapter\u003c\/a\u003e. The adapter and the \u003ca href=\"\/it\/products\/omicron-lab-bode-100-vector-network-analyser-uk\"\u003eBode 100\u003c\/a\u003e or \u003ca href=\"\/it\/products\/omicron-lab-bode-500-vector-network-analyser-vna\"\u003eBode 500\u003c\/a\u003e analyser are not included.\u003c\/li\u003e\n  \u003cli\u003eB-TCA limits are 60 V DC or 30 V AC, 1 A, and under 350 mJ stored in an inductive DUT. Use only DC sources isolated from mains.\u003c\/li\u003e\n  \u003cli\u003eThe B-TCA has no internal bias-T. Above 3.3 V DC, OMICRON Lab suggests an external bias-T between the analyser and the adapter.\u003c\/li\u003e\n  \u003cli\u003eSensitivity degrades above 100 Ω. For 1 kΩ to 1 MΩ choose the \u003ca href=\"\/it\/products\/test-card-set-series-thru\"\u003eSeries-Thru set\u003c\/a\u003e; to push a shunt measurement up to 4,500 Ω, use the \u003ca href=\"\/it\/products\/test-card-set-shunt-thru-with-rs\"\u003eShunt-Thru with Rs set\u003c\/a\u003e with a 950 Ω Rs.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eB-TCA Test Card Set Comparison\u003c\/h2\u003e\n\u003cdiv style=\"overflow-x:auto\"\u003e\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth scope=\"col\"\u003eFeature\u003c\/th\u003e\n\u003cth\u003e\u003ca href=\"\/it\/products\/omicron-lab-b-tca-test-card-adapter-p0009653\"\u003eB-TCA adapter\u003c\/a\u003e\u003c\/th\u003e\n\u003cth\u003eShunt-Thru set\u003c\/th\u003e\n\u003cth\u003e\u003ca href=\"\/it\/products\/test-card-set-series-thru\"\u003eSeries-Thru set\u003c\/a\u003e\u003c\/th\u003e\n\u003cth\u003e\u003ca href=\"\/it\/products\/test-card-set-one-port\"\u003eOne-Port set\u003c\/a\u003e\u003c\/th\u003e\n\u003cth\u003e\u003ca href=\"\/it\/products\/test-card-set-shunt-thru-with-rs\"\u003eShunt-Thru with Rs set\u003c\/a\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eOrder number\u003c\/th\u003e\n\u003ctd\u003eP0009653\u003c\/td\u003e\n\u003ctd\u003eP0011462\u003c\/td\u003e\n\u003ctd\u003eP0011464\u003c\/td\u003e\n\u003ctd\u003eP0011465\u003c\/td\u003e\n\u003ctd\u003eP0011466\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eContents\u003c\/th\u003e\n\u003ctd\u003eAdapter, 2 N-N and 2 N-BNC cables, 4 calibrators, 32 test cards (8 per setup)\u003c\/td\u003e\n\u003ctd\u003e32 test cards, 1 calibrator\u003c\/td\u003e\n\u003ctd\u003e32 test cards, 1 calibrator\u003c\/td\u003e\n\u003ctd\u003e32 test cards, 1 calibrator\u003c\/td\u003e\n\u003ctd\u003e32 test cards, 1 calibrator\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTest card colour\u003c\/th\u003e\n\u003ctd\u003eAll four\u003c\/td\u003e\n\u003ctd\u003eBlue\u003c\/td\u003e\n\u003ctd\u003eRed\u003c\/td\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003ctd\u003eGreen\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eBest-suited impedance range\u003c\/th\u003e\n\u003ctd\u003eMilliohms to megohms across four setups\u003c\/td\u003e\n\u003ctd\u003e1 mΩ to 100 Ω\u003c\/td\u003e\n\u003ctd\u003e1 kΩ to 1 MΩ\u003c\/td\u003e\n\u003ctd\u003e500 mΩ to 10 kΩ\u003c\/td\u003e\n\u003ctd\u003eSet by Rs: 1 mΩ to 100 Ω (0 Ω) up to 20 mΩ to 4,500 Ω (950 Ω)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eMax. recommended DUT size\u003c\/th\u003e\n\u003ctd\u003ePer setup\u003c\/td\u003e\n\u003ctd\u003e≈ 9 mm contact to contact, 10 mm wide\u003c\/td\u003e\n\u003ctd\u003e≈ 9 mm contact to contact\u003c\/td\u003e\n\u003ctd\u003e15 mm contact to contact\u003c\/td\u003e\n\u003ctd\u003e≈ 9 mm x 9 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eShort-Delay Time\u003c\/th\u003e\n\u003ctd\u003ePer setup\u003c\/td\u003e\n\u003ctd\u003e23 ps\u003c\/td\u003e\n\u003ctd\u003e0 ps\u003c\/td\u003e\n\u003ctd\u003e0 ps\u003c\/td\u003e\n\u003ctd\u003e23 ps\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePrice\u003c\/th\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"omicron-lab-b-tca-test-card-adapter-p0009653\"\u003e£950\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"test-card-set-shunt-thru\"\u003e£175\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"test-card-set-series-thru\"\u003e£165.02\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"test-card-set-one-port\"\u003e£175\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"test-card-set-shunt-thru-with-rs\"\u003e£175\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003c\/div\u003e\n\n\u003ch2\u003eTypical Applications\u003c\/h2\u003e\n\u003cp\u003eImpedance against frequency, up to 450 MHz, of SMD parts whose impedance magnitude sits between 1 mΩ and 100 Ω. Low-impedance measurements where the One-Port setup's 500 mΩ lower limit is too high.\u003c\/p\u003e\n\u003cp\u003eThis set suits engineers who already run a B-TCA and have used up the eight Shunt-Thru cards supplied with it.\u003c\/p\u003e\n\n\u003ch2\u003eWhat's Included\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003e32 Shunt-Thru test cards (4 × 8)\u003c\/li\u003e\n  \u003cli\u003e1 Shunt-Thru calibrator\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eThe OMICRON Lab Test Card Set - Shunt-Thru is \u003cspan data-ds-price=\"test-card-set-shunt-thru\"\u003e£175\u003c\/span\u003e ex VAT. If you do not have the adapter yet, the \u003ca href=\"\/it\/products\/omicron-lab-b-tca-test-card-adapter-p0009653\"\u003eB-TCA\u003c\/a\u003e ships with eight cards and a calibrator per setup; contact us for a formal quotation.\u003c\/p\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003ch3\u003eWhy Choose Shunt-Thru Over One-Port for Low Impedance?\u003c\/h3\u003e\n\u003cp\u003eBecause its best-suited range starts at 1 mΩ, against 500 mΩ for One-Port. OMICRON Lab rates Shunt-Thru best and One-Port only OK for low impedance, as the One-Port range is limited by contact resistance and the analyser's signal-to-noise ratio.\u003c\/p\u003e\n\u003cp\u003e\u003csmall\u003eAnswered by John Legg, Director, Debug Store\u003c\/small\u003e\u003c\/p\u003e\n\u003ch3\u003eIs This the Same as the Shunt-Thru with Rs Set?\u003c\/h3\u003e\n\u003cp\u003eNo. Shunt-Thru with Rs cards are green and carry extra solder locations for two series resistors (Rs, 0603 to 1206), which move the measurement range upwards. With Rs at 0 Ω that setup behaves like Shunt-Thru, but the blue Shunt-Thru cards here need no resistors.\u003c\/p\u003e\n\u003cp\u003e\u003csmall\u003eAnswered by John Legg, Director, Debug Store\u003c\/small\u003e\u003c\/p\u003e\n\n\u003cp\u003e\u003csmall\u003eLast reviewed: 18 November 2026\u003c\/small\u003e\u003c\/p\u003e\n\u003cdetails\u003e\u003csummary\u003e\u003csmall\u003eSources (1 manufacturer page, 1 user manual)\u003c\/small\u003e\u003c\/summary\u003e\u003cul\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.omicron-lab.com\/products\/vector-network-analysis\/accessories\/b-tca-test-card-adapter\"\u003eOMICRON Lab B-TCA Test Card Adapter\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/files.thedebugstore.com\/omicron-lab\/p0009653\/omicron-lab-b-tca-test-card-adapter-user-manual.pdf\"\u003eB-TCA User Manual (ENU 1302 05 02)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/details\u003e","brand":"OMICRON-Lab","offers":[{"title":"Default Title","offer_id":55280504078711,"sku":"P0011462","price":175.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0522\/6931\/8333\/files\/omicron-lab-test-card-set-shunt-thru-card-set.png?v=1795011456","url":"https:\/\/thedebugstore.com\/it\/products\/test-card-set-shunt-thru","provider":"Debug Store","version":"1.0","type":"link"}