{"title":"SEGGER Debuggers","description":"\u003cp\u003eSEGGER Debuggers, available from Debug Store, are high-performance tools for embedded system development. They offer seamless integration with various IDEs, support a wide range of microcontrollers, and provide features like real-time transfer, flash breakpoints, and unlimited flash breakpoints. These debuggers enable efficient debugging, programming, and testing of embedded systems, making them essential for electronic design engineers.\u003c\/p\u003e","products":[{"product_id":"segger-j-link-pro-debugger-programmer-8-12-00","title":"SEGGER J-Link PRO, sonda di debug Ethernet\/USB ultraveloce","description":"\u003cp\u003eLa SEGGER J-Link PRO (codice 8.12.00) è una sonda di debug JTAG\/SWD Ethernet e USB con velocità dell'interfaccia target fino a 50 MHz, velocità di download fino a 4 MB\/s e interfaccia target da 1.2V a 5V. Aggiunge una porta Ethernet da 100 Mbit\/s con web server integrato, la misura analogica della potenza a 200 kHz con risoluzione di 50µA e le licenze per J-Flash, Unlimited Flash Breakpoints, Ozone e RDI. È adatta ai team firmware che devono raggiungere un target attraverso la LAN, lontano dal PC host, su dispositivi ARM Cortex, RISC-V, Renesas RX e Microchip PIC32.\u003c\/p\u003e\n\n\u003ch2\u003eDebug JTAG\/SWD remoto via Ethernet\u003c\/h2\u003e\n\u003cp\u003eLa sonda si collega via Ethernet a 100 Mbit\/s o USB 2.0 Hi-Speed, quindi la stessa unità può stare sulla scrivania o in rete. Alla consegna è configurata per il DHCP e con J-Link Configurator si può impostare un indirizzo statico. Un web server integrato sulla porta TCP 80 consente la configurazione da browser. SEGGER propone l'interfaccia Ethernet per il debug remoto in team distribuiti e grandi ambienti di sviluppo. Le linee dati Ethernet sono isolate secondo IEEE 802.3 con una tensione di prova di 1500 Vrms per un minuto.\u003c\/p\u003e\n\n\u003ch2\u003eInterfaccia a 50 MHz, download a 4 MB\/s e misura della potenza\u003c\/h2\u003e\n\u003cp\u003eSEGGER indica fino a 50 MHz di velocità dell'interfaccia target e fino a 4 MB\/s di velocità di download, contro i 15 MHz e 1 MB\/s massimi di J-Link BASE e PLUS. Il segnale SWO viene campionato fino a 100 MHz. La PRO misura la corrente del target con una frequenza di campionamento di 200 kHz e una risoluzione di 50µA, e può alimentare il target con 5V fino a 300mA prelevati dalla linea USB. Il target utilizza il connettore standard J-Link a 20 pin da 0.1\"; le assegnazioni dei pin e gli adattatori sono nella nostra guida \u003ca href=\"\/it\/pages\/segger-j-link-20-pin-connector-pinout\"\u003epinout del connettore SEGGER J-Link a 20 pin\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ch2\u003eInterfacce, core supportati e licenze\u003c\/h2\u003e\n\u003cp\u003eLe interfacce di debug supportate sono JTAG, cJTAG, SWD, SWD multi-drop, SWO, SPI, Microchip ICSP, Renesas FINE e Silicon Labs C2. L'elenco dei core di SEGGER comprende ARM da Cortex-M0 a Cortex-M85, Cortex-A e Cortex-R, i core ARM di generazioni precedenti da ARM7 a ARM11, core RISC-V di SiFive, Andes, Codasip e Nuclei, Renesas RX, Microchip PIC32, Silicon Labs EFM8 e Cadence Tensilica Xtensa. La licenza J-Flash è preinstallata sulla sonda, quindi non c'è nulla da attivare; sono inclusi anche Unlimited Flash Breakpoints, Ozone e RDI. Il debug in monitor mode è supportato sui core ARMv7-M e ARMv8-M, e sono supportati RTT e VCOM (pin 5 e 17, solo SWD).\u003c\/p\u003e\n\n\u003ch2\u003eSoftware e compatibilità con gli IDE\u003c\/h2\u003e\n\u003cp\u003eIl software J-Link è gratuito, per Windows e Linux (x86-64 e ARM64) e macOS (x86-64 e Apple Silicon). SEGGER indica il supporto, tra gli altri, in SEGGER Embedded Studio, Eclipse, IAR EWARM, Keil MDK-ARM, STM32CubeIDE, MCUXpresso e Visual Studio Code.\u003c\/p\u003e\n\n\u003ch2\u003eContenuto della confezione\u003c\/h2\u003e\n\u003cp\u003eSonda J-Link PRO, cavo piatto a 20 pin da 0.1\" e cavo USB-C.\u003c\/p\u003e\n\n\u003ch2\u003eSpecifiche\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eInterfacce host\u003c\/th\u003e\n\u003ctd\u003eEthernet 100 Mbit\/s; USB 2.0 Hi-Speed\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eConnettore target\u003c\/th\u003e\n\u003ctd\u003eJTAG\/SWD a 20 pin, 0.1\" (2.54mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eInterfacce di debug supportate\u003c\/th\u003e\n\u003ctd\u003eJTAG, cJTAG, SWD, SWD multi-drop, SWO, SPI, Microchip ICSP, Renesas FINE, Silicon Labs C2\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTensione dell'interfaccia target (VIF)\u003c\/th\u003e\n\u003ctd\u003eDa 1.2V a 5V\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eCorrente assorbita da VTref\u003c\/th\u003e\n\u003ctd\u003eMeno di 25µA\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eAlimentazione del target\u003c\/th\u003e\n\u003ctd\u003e5V (derivati da USB), max. 300mA\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eVelocità dell'interfaccia target\u003c\/th\u003e\n\u003ctd\u003eMax. 50 MHz\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eFrequenza di campionamento SWO\u003c\/th\u003e\n\u003ctd\u003eMax. 100 MHz\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eVelocità di download\u003c\/th\u003e\n\u003ctd\u003eFino a 4 MB\/s\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eMisura della potenza\u003c\/th\u003e\n\u003ctd\u003eFrequenza di campionamento 200 kHz, risoluzione 50µA\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eIsolamento Ethernet\u003c\/th\u003e\n\u003ctd\u003eLinee dati secondo IEEE 802.3, 1500 Vrms per un minuto\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eLicenze incluse\u003c\/th\u003e\n\u003ctd\u003eJ-Flash (preinstallata), Unlimited Flash Breakpoints, Ozone, RDI\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDimensioni (senza cavi)\u003c\/th\u003e\n\u003ctd\u003e100mm x 53mm x 27mm\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePeso (senza cavi)\u003c\/th\u003e\n\u003ctd\u003e73g\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTemperatura di esercizio\u003c\/th\u003e\n\u003ctd\u003eDa +5°C a +60°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTemperatura di stoccaggio\u003c\/th\u003e\n\u003ctd\u003eDa -20°C a +65°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eUmidità relativa\u003c\/th\u003e\n\u003ctd\u003eMax. 90% rH, senza condensa\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eEMC\u003c\/th\u003e\n\u003ctd\u003eEN 55024, EN 55032\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eSistema operativo host\u003c\/th\u003e\n\u003ctd\u003eWindows e Linux (x86-64, ARM64); macOS (x86-64, Apple Silicon)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eLimitazioni\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eÈ supportata una sola connessione Ethernet alla volta.\u003c\/li\u003e\n  \u003cli\u003eNessun Power over Ethernet; per i nodi di test farm alimentati in PoE scelga la J-Link PRO PoE.\u003c\/li\u003e\n  \u003cli\u003eLo schermo Ethernet non è isolato; per un isolamento efficace SEGGER prescrive un cavo a doppino non schermato.\u003c\/li\u003e\n  \u003cli\u003eI valori di 50 MHz e 4 MB\/s sono massimi; il clock di interfaccia utilizzabile e la velocità di programmazione della flash dipendono dal dispositivo target.\u003c\/li\u003e\n  \u003cli\u003eNessun trace ETM su Cortex-M (usare SEGGER J-Trace) e nessuna interfaccia target QSPI.\u003c\/li\u003e\n  \u003cli\u003eVCOM è disponibile solo durante il debug in SWD.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eJ-Link PRO a confronto con i modelli correlati\u003c\/h2\u003e\n\u003cdiv style=\"overflow-x:auto\"\u003e\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eModello\u003c\/th\u003e\n\u003cth\u003eInterfaccia host\u003c\/th\u003e\n\u003cth\u003eVelocità di download\u003c\/th\u003e\n\u003cth\u003eVelocità dell'interfaccia target\u003c\/th\u003e\n\u003cth\u003eEthernet\u003c\/th\u003e\n\u003cth\u003ePower over Ethernet\u003c\/th\u003e\n\u003cth\u003ePrezzo IVA esclusa\u003c\/th\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-8-02-28-j-link-plus-classic-debugger\"\u003eJ-Link PLUS Classic\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eUSB 2.0 Hi-Speed\u003c\/td\u003e\n\u003ctd\u003eFino a 1 MB\/s\u003c\/td\u003e\n\u003ctd\u003eFino a 15 MHz\u003c\/td\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-8-02-28-j-link-plus-classic-debugger\"\u003e£660\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-j-link-ultra-plus-8-16-28\"\u003eJ-Link ULTRA+ (J-Link Ultra)\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eUSB 2.0 Hi-Speed\u003c\/td\u003e\n\u003ctd\u003eFino a 4 MB\/s\u003c\/td\u003e\n\u003ctd\u003eFino a 50 MHz\u003c\/td\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-j-link-ultra-plus-8-16-28\"\u003e£870\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eJ-Link PRO (questo prodotto)\u003c\/td\u003e\n\u003ctd\u003eUSB 2.0 Hi-Speed ed Ethernet 100 Mbit\/s\u003c\/td\u003e\n\u003ctd\u003eFino a 4 MB\/s\u003c\/td\u003e\n\u003ctd\u003eFino a 50 MHz\u003c\/td\u003e\n\u003ctd\u003eSì\u003c\/td\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-j-link-pro-debugger-programmer-8-12-00\"\u003e£1,100\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-8-12-28-j-link-pro-poe-debugger-uk\"\u003eJ-Link PRO PoE\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eUSB 2.0 Hi-Speed ed Ethernet 100 Mbit\/s\u003c\/td\u003e\n\u003ctd\u003eFino a 4 MB\/s\u003c\/td\u003e\n\u003ctd\u003eFino a 50 MHz\u003c\/td\u003e\n\u003ctd\u003eSì\u003c\/td\u003e\n\u003ctd\u003eSì, IEEE 802.3af\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-8-12-28-j-link-pro-poe-debugger-uk\"\u003e£1,320\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-j-link-wifi-8-14-28\"\u003eJ-Link WiFi\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eUSB 2.0 Hi-Speed e WiFi IEEE 802.11 b\/g\/n\u003c\/td\u003e\n\u003ctd\u003eFino a 1 MB\/s\u003c\/td\u003e\n\u003ctd\u003eFino a 15 MHz\u003c\/td\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-j-link-wifi-8-14-28\"\u003e£1,100\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003c\/div\u003e\n\n\u003ch2\u003eApplicazioni tipiche\u003c\/h2\u003e\n\u003cp\u003eDebug di una scheda Cortex-M33 o Cortex-A in laboratorio da una scrivania a un altro piano, attraverso la LAN aziendale. Hardware da banco condiviso da un team firmware distribuito, raggiunto tramite indirizzo IP anziché con un cavo USB.\u003c\/p\u003e\n\u003cp\u003eScelga la ULTRA+ per gli stessi valori di 50 MHz e 4 MB\/s solo via USB, oppure la PRO PoE per nodi di test farm alimentati dalla rete.\u003c\/p\u003e\n\n\u003cp\u003eOrdini la J-Link PRO a \u003cspan data-ds-price=\"segger-j-link-pro-debugger-programmer-8-12-00\"\u003e£1,100\u003c\/span\u003e IVA esclusa. Verifichi il codice del suo dispositivo nell'elenco dei dispositivi supportati da SEGGER, oppure ci chieda un preventivo formale. Veda l'intera gamma nella nostra collezione \u003ca href=\"\/it\/collections\/segger-debugger-catalogue-uk\"\u003esonde di debug SEGGER\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003cp\u003e\u003csmall\u003eUltima revisione: 16 novembre 2026.\u003c\/small\u003e\u003c\/p\u003e\n\u003cdetails\u003e\u003csummary\u003e\u003csmall\u003eFonti (7 pagine del produttore)\u003c\/small\u003e\u003c\/summary\u003e\u003cul\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/debug-probes\/j-link\/models\/j-link-pro\/\"\u003ePagina prodotto SEGGER J-Link Pro\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/J-Link_PRO\"\u003eSEGGER Knowledge Base: J-Link PRO\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/Setting_up_Ethernet_interface\"\u003eSEGGER Knowledge Base: configurazione dell'interfaccia Ethernet\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/debug-probes\/j-link\/models\/j-link-pro-poe\/\"\u003ePagina prodotto SEGGER J-Link Pro PoE\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/purchase\/pricing\/jlink-related\/\"\u003ePrezzi e licenze SEGGER J-Link\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/Using_J-Link_VCOM_functionality\"\u003eSEGGER Knowledge Base: utilizzo della funzionalità VCOM di J-Link\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/Supported_IDEs\"\u003eSEGGER Knowledge Base: IDE supportati\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/details\u003e","brand":"SEGGER Microcontroller GmbH","offers":[{"title":"Default Title","offer_id":44263171948767,"sku":"8.12.00","price":1100.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0522\/6931\/8333\/files\/segger-microcontroller-gmbh-8-12-00-40189792583903.jpg?v=1688907179"},{"product_id":"segger-j-link-wifi-8-14-28","title":"SEGGER J-Link WiFi Wireless Debug Probe (8.14.28)","description":"\u003cp\u003eThe SEGGER J-Link WiFi (part number 8.14.28) is a JTAG\/SWD debug probe that connects to the host over IEEE 802.11 b\/g\/n WiFi in the 2.4 GHz band, or over USB 2.0 Hi-Speed, with up to 15 MHz target interface speed, download speeds up to 1 MB\/s and a 1.2V to 5V target interface. SEGGER lists J-Flash, Unlimited Flash Breakpoints, Ozone and RDI licences with it. It is built for targets that move, as in robotics, or that must stay shielded or inside a hazardous area, away from the development PC.\u003c\/p\u003e\n\n\u003ch2\u003eWireless JTAG\/SWD Debug Probe for Moving or Shielded Targets\u003c\/h2\u003e\n\u003cp\u003eThe probe travels with the target and links to the PC over WiFi, so a robot arm or a moving platform can be debugged without a USB cable trailing back to the bench. Where the target operates in a hazardous environment, the PC and the engineer can stay outside, behind a physical barrier. The J-Link WiFi is USB powered and shares that supply with the target: it can supply the target with 5V at up to 300mA. On the target side it uses the standard J-Link 20-pin 0.1\" connector; pin assignments and adapter options are in our \u003ca href=\"\/it\/pages\/segger-j-link-20-pin-connector-pinout\"\u003eSEGGER J-Link 20-pin connector pinout\u003c\/a\u003e guide.\u003c\/p\u003e\n\n\u003ch2\u003eWiFi Setup Over USB\u003c\/h2\u003e\n\u003cp\u003eThe network is set up while the probe is connected by USB. In J-Link Configurator you enter the SSID and password in the WiFi configuration section; in J-Link Commander the SetWifi command sets the SSID. SEGGER notes that WiFi probes are usually only shown in J-Link Configurator when connected via USB, and that UDP discovery will usually not work for them.\u003c\/p\u003e\n\n\u003ch2\u003eLicences, Debug Interfaces, RTT and VCOM\u003c\/h2\u003e\n\u003cp\u003eSEGGER's licence overview lists J-Flash, Unlimited Flash Breakpoints, Ozone and RDI as included with the J-Link WiFi, with monitor-mode debugging. Supported debug interfaces are JTAG, cJTAG, SWD, SWD multi-drop, SWO, SPI, Microchip ICSP, Renesas FINE and Silicon Labs C2. SEGGER's cores list covers ARM Cortex-M, Cortex-A and Cortex-R, legacy ARM7 to ARM11, RISC-V cores from SiFive, Andes, Codasip and Nuclei, Renesas RX, Microchip PIC32, Silicon Labs EFM8 and Cadence Tensilica Xtensa. Real Time Transfer (RTT) moves data between the running target and the host over the debug connection, and VCOM bridges a target UART to a virtual COM port when debugging over SWD.\u003c\/p\u003e\n\n\u003ch2\u003eSoftware and IDE Compatibility\u003c\/h2\u003e\n\u003cp\u003eJ-Link software is free of charge. The software runs on Windows (x86-64 and ARM64), Linux (x86-64 and ARM64) and macOS (x86-64 and Apple Silicon). SEGGER lists support in SEGGER Embedded Studio, Eclipse, IAR EWARM, Keil MDK-ARM, STM32CubeIDE, MCUXpresso and Visual Studio Code, among others.\u003c\/p\u003e\n\n\u003ch2\u003eWhat's Included\u003c\/h2\u003e\n\u003cp\u003eJ-Link WiFi probe, 20-pin 0.1\" ribbon cable and a USB cable.\u003c\/p\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eHost interfaces\u003c\/th\u003e\n\u003ctd\u003eIEEE 802.11 b\/g\/n WiFi, 2.4 GHz; USB 2.0 Hi-Speed\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget connector\u003c\/th\u003e\n\u003ctd\u003eJTAG\/SWD 20-pin, 0.1\" (2.54mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eSupported debug interfaces\u003c\/th\u003e\n\u003ctd\u003eJTAG, cJTAG, SWD, SWD multi-drop, SWO, SPI, Microchip ICSP, Renesas FINE, Silicon Labs C2\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget interface voltage (VIF)\u003c\/th\u003e\n\u003ctd\u003e1.2V to 5V\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eCurrent drawn from VTref\u003c\/th\u003e\n\u003ctd\u003eLess than 25µA\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget supply\u003c\/th\u003e\n\u003ctd\u003e5V (derived from USB), max. 300mA\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget interface speed\u003c\/th\u003e\n\u003ctd\u003eMax. 15 MHz\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eSWO sampling frequency\u003c\/th\u003e\n\u003ctd\u003eMax. 30 MHz\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDownload speed\u003c\/th\u003e\n\u003ctd\u003eUp to 1 MB\/s\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePower supply\u003c\/th\u003e\n\u003ctd\u003eUSB powered, max. 220mA at 5V\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eIncluded licences\u003c\/th\u003e\n\u003ctd\u003eJ-Flash, Unlimited Flash Breakpoints, Ozone, RDI\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDimensions (without cables)\u003c\/th\u003e\n\u003ctd\u003e103mm x 53mm x 28mm\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eWeight (without cables)\u003c\/th\u003e\n\u003ctd\u003e70g\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eOperating temperature\u003c\/th\u003e\n\u003ctd\u003e+5°C to +60°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eStorage temperature\u003c\/th\u003e\n\u003ctd\u003e-20°C to +65°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eRelative humidity\u003c\/th\u003e\n\u003ctd\u003eMax. 90% rH, non-condensing\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eStandards (listed by SEGGER under EMC)\u003c\/th\u003e\n\u003ctd\u003eEN 301 489-1\/-17, EN 300 328, EN 62368\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eHost OS\u003c\/th\u003e\n\u003ctd\u003eWindows and Linux (x86-64, ARM64); macOS (x86-64, Apple Silicon)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eLimitations\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eWiFi is 2.4 GHz IEEE 802.11 b\/g\/n only.\u003c\/li\u003e\n  \u003cli\u003eInitial WiFi setup needs a USB connection, and UDP discovery will usually not work over WiFi.\u003c\/li\u003e\n  \u003cli\u003eDownload speed is up to 1 MB\/s and target interface speed up to 15 MHz; the J-Link ULTRA+ and PRO models reach up to 4 MB\/s and 50 MHz.\u003c\/li\u003e\n  \u003cli\u003eNo ETM trace on Cortex-M (use SEGGER J-Trace) and no QSPI target interface.\u003c\/li\u003e\n  \u003cli\u003eVCOM is available only when debugging over SWD.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eJ-Link WiFi Compared with PLUS and PRO\u003c\/h2\u003e\n\u003cdiv style=\"overflow-x:auto\"\u003e\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eHost interface\u003c\/th\u003e\n\u003cth\u003eDownload speed\u003c\/th\u003e\n\u003cth\u003eTarget interface speed\u003c\/th\u003e\n\u003cth\u003eEthernet\u003c\/th\u003e\n\u003cth\u003ePrice ex VAT\u003c\/th\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eJ-Link WiFi (this product)\u003c\/td\u003e\n\u003ctd\u003eUSB 2.0 Hi-Speed and IEEE 802.11 b\/g\/n WiFi\u003c\/td\u003e\n\u003ctd\u003eUp to 1 MB\/s\u003c\/td\u003e\n\u003ctd\u003eUp to 15 MHz\u003c\/td\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-j-link-wifi-8-14-28\"\u003e£1,100\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-8-02-28-j-link-plus-classic-debugger\"\u003eJ-Link PLUS Classic\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eUSB 2.0 Hi-Speed\u003c\/td\u003e\n\u003ctd\u003eUp to 1 MB\/s\u003c\/td\u003e\n\u003ctd\u003eUp to 15 MHz\u003c\/td\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-8-02-28-j-link-plus-classic-debugger\"\u003e£660\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-j-link-pro-debugger-programmer-8-12-00\"\u003eJ-Link PRO\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eUSB 2.0 Hi-Speed and 100 Mbit\/s Ethernet\u003c\/td\u003e\n\u003ctd\u003eUp to 4 MB\/s\u003c\/td\u003e\n\u003ctd\u003eUp to 50 MHz\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-j-link-pro-debugger-programmer-8-12-00\"\u003e£1,100\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-8-12-28-j-link-pro-poe-debugger-uk\"\u003eJ-Link PRO PoE\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eUSB 2.0 Hi-Speed and 100 Mbit\/s Ethernet\u003c\/td\u003e\n\u003ctd\u003eUp to 4 MB\/s\u003c\/td\u003e\n\u003ctd\u003eUp to 50 MHz\u003c\/td\u003e\n\u003ctd\u003eYes, with IEEE 802.3af PoE\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-8-12-28-j-link-pro-poe-debugger-uk\"\u003e£1,320\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003c\/div\u003e\n\n\u003ch2\u003eTypical Applications\u003c\/h2\u003e\n\u003cp\u003eDebugging the Cortex-M motor controller of a mobile robot while it drives, with RTT logs streamed back to the PC. Firmware work on a target that runs inside a test chamber or a guarded machine cell, with the engineer outside the barrier.\u003c\/p\u003e\n\u003cp\u003eIf the probe can stay wired to a network, the J-Link PRO adds 50 MHz and 4 MB\/s over Ethernet.\u003c\/p\u003e\n\n\u003cp\u003eOrder the J-Link WiFi for \u003cspan data-ds-price=\"segger-j-link-wifi-8-14-28\"\u003e£1,100\u003c\/span\u003e ex VAT. Check your part number against SEGGER's supported devices list, or ask us for a formal quotation. See the full range in our \u003ca href=\"\/it\/collections\/segger-debugger-catalogue-uk\"\u003eSEGGER debug probes\u003c\/a\u003e collection.\u003c\/p\u003e\n\n\u003cp\u003e\u003csmall\u003eLast reviewed 16\/11\/2026.\u003c\/small\u003e\u003c\/p\u003e\n\u003cdetails\u003e\u003csummary\u003e\u003csmall\u003eSources (6 manufacturer pages)\u003c\/small\u003e\u003c\/summary\u003e\u003cul\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/debug-probes\/j-link\/models\/j-link-wifi\/\"\u003eSEGGER J-Link WiFi product page\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/J-Link_WiFi\"\u003eSEGGER Knowledge Base: J-Link WiFi\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/Setting_up_Ethernet_interface\"\u003eSEGGER Knowledge Base: Setting up Ethernet interface (WiFi setup)\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/purchase\/pricing\/jlink-related\/\"\u003eSEGGER J-Link pricing and licence overview\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/shop-us.segger.com\/product\/j-link-wifi-8-14-28\/\"\u003eSEGGER US shop: J-Link WiFi (8.14.28)\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/Supported_IDEs\"\u003eSEGGER Knowledge Base: Supported IDEs\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/details\u003e","brand":"SEGGER Microcontroller GmbH","offers":[{"title":"Default Title","offer_id":44263172014303,"sku":"8.14.28","price":1100.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0522\/6931\/8333\/files\/segger-microcontroller-gmbh-8-14-28-segger-j-link-wifi-8-14-28-42714466615519.png?v=1722900000"},{"product_id":"segger-8-08-00-j-link-base-classic","title":"Sonda di debug USB JTAG\/SWD SEGGER J-Link BASE Classic","description":"\u003cp\u003eLa SEGGER J-Link BASE Classic (codice 8.08.00) è una sonda di debug JTAG\/SWD alimentata via USB, in un contenitore da banco di 100mm x 53mm x 27mm, con interfaccia target da 1.2V a 5V, velocità dell'interfaccia target fino a 15 MHz e velocità di download fino a 1 MB\/s. Offre le stesse funzioni J-Link BASE del modello Compact, con una porta host USB Type B. È adatta al bring-up del firmware e al debug quotidiano al banco su target ARM Cortex, RISC-V, Renesas RX e Microchip PIC32.\u003c\/p\u003e\n\n\u003ch2\u003eSonda di debug JTAG\/SWD da banco\u003c\/h2\u003e\n\u003cp\u003eLa Classic è il contenitore J-Link a grandezza piena, 70g senza cavi, pensato per stare accanto alla scheda sul banco. Il collegamento con l'host è USB 2.0 Hi-Speed tramite connettore USB Type B e la sonda è alimentata via USB. Lato target utilizza il connettore J-Link standard a 20 pin da 0.1\" presente sulla maggior parte dei modelli J-Link. Assegnazione dei pin e adattatori disponibili sono descritti nella nostra guida \u003ca href=\"\/it\/pages\/segger-j-link-20-pin-connector-pinout\"\u003epiedinatura del connettore a 20 pin SEGGER J-Link\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ch2\u003eInterfacce target e core supportati\u003c\/h2\u003e\n\u003cp\u003eL'hardware J-Link BASE attuale supporta JTAG, cJTAG, SWD, SWD multi-drop, SWO, SPI, Microchip ICSP, Renesas FINE e Silicon Labs C2. L'elenco dei core supportati da SEGGER comprende ARM Cortex-M0 fino a Cortex-M85, Cortex-A e Cortex-R, i precedenti ARM7 fino ad ARM1176, core RISC-V di SiFive, Andes, Codasip e Nuclei, Renesas RX, Microchip PIC32 e Silicon Labs EFM8. La sonda può anche alimentare il target a 5V fino a 300mA dalla linea USB.\u003c\/p\u003e\n\n\u003ch2\u003eSupporto di RTT, VCOM e trace buffer\u003c\/h2\u003e\n\u003cp\u003eSEGGER Real Time Transfer (RTT) trasferisce dati tra il target in esecuzione e l'host attraverso la connessione di debug, così potete registrare log o interagire con un'applicazione senza bisogno di una UART libera. Dove è disponibile una UART, la funzione VCOM la collega a una porta COM virtuale sul PC utilizzando i pin 5 (J-Link Tx) e 17 (J-Link Rx) del connettore a 20 pin; VCOM funziona solo durante il debug via SWD. Embedded Trace Buffer (ETB) e Micro Trace Buffer (MTB) sono supportati quando il target li implementa.\u003c\/p\u003e\n\n\u003ch2\u003eSoftware, IDE e percorso di aggiornamento\u003c\/h2\u003e\n\u003cp\u003eIl software J-Link e gli aggiornamenti del firmware sono gratuiti. Il software di configurazione e controllo funziona su Windows (x86-64 e ARM64), Linux (x86-64 e ARM64) e macOS (x86-64 e Apple Silicon). SEGGER indica il supporto completo in SEGGER Embedded Studio, Eclipse, IAR EWARM, Keil MDK-ARM, STM32CubeIDE, MCUXpresso e Visual Studio Code, tra gli altri. Più J-Link possono funzionare da un unico PC, ciascuno identificato dal proprio numero di serie.\u003c\/p\u003e\n\n\u003ch2\u003eContenuto della confezione\u003c\/h2\u003e\n\u003cp\u003eSonda J-Link BASE Classic, cavo piatto a 20 pin da 0.1\" (18cm) e un cavo USB. Non è incluso alcun adattatore per i connettori Cortex Debug a 10 pin da 0.05\".\u003c\/p\u003e\n\n\u003ch2\u003eSpecifiche\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eInterfaccia host\u003c\/th\u003e\n\u003ctd\u003eUSB 2.0 Hi-Speed, USB Type B\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eInterfaccia target\u003c\/th\u003e\n\u003ctd\u003eJTAG\/SWD a 20 pin, 0.1\" (2.54mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eInterfacce di debug supportate\u003c\/th\u003e\n\u003ctd\u003eJTAG, cJTAG, SWD, SWD multi-drop, SWO, SPI, Microchip ICSP, Renesas FINE, Silicon Labs C2\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTensione dell'interfaccia target (VIF)\u003c\/th\u003e\n\u003ctd\u003eDa 1.2V a 5V\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eCorrente assorbita da VTref\u003c\/th\u003e\n\u003ctd\u003eMeno di 25µA\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eAlimentazione del target\u003c\/th\u003e\n\u003ctd\u003e5V (derivati da USB), max. 300mA\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eVelocità dell'interfaccia target\u003c\/th\u003e\n\u003ctd\u003eMax. 15 MHz\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eFrequenza di campionamento SWO\u003c\/th\u003e\n\u003ctd\u003eMax. 30 MHz\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eVelocità di download\u003c\/th\u003e\n\u003ctd\u003eFino a 1 MB\/s\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eAlimentazione\u003c\/th\u003e\n\u003ctd\u003eAlimentata via USB, max. 50mA più la corrente di alimentazione del target\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDimensioni (senza cavi)\u003c\/th\u003e\n\u003ctd\u003e100mm x 53mm x 27mm\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePeso (senza cavi)\u003c\/th\u003e\n\u003ctd\u003e70g\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTemperatura di esercizio\u003c\/th\u003e\n\u003ctd\u003eDa +5°C a +60°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTemperatura di stoccaggio\u003c\/th\u003e\n\u003ctd\u003eDa -20°C a +65°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eUmidità relativa\u003c\/th\u003e\n\u003ctd\u003eMax. 90% UR, senza condensa\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eEMC\u003c\/th\u003e\n\u003ctd\u003eEN 55022, EN 55024\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eSistema operativo host\u003c\/th\u003e\n\u003ctd\u003eWindows e Linux (x86-64, ARM64); macOS (x86-64, Apple Silicon)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eLimiti\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eJ-Flash e J-Flash SPI, Unlimited Flash Breakpoints, il debugger Ozone e il pacchetto di licenze RDI non sono inclusi, e SEGGER colloca il debug in modalità monitor nell'upgrade PLUS. Sono forniti con la J-Link PLUS, oppure con la licenza di upgrade da BASE a PLUS per una BASE esistente.\u003c\/li\u003e\n  \u003cli\u003eLa velocità di download arriva fino a 1 MB\/s; SEGGER indica fino a 4 MB\/s per i modelli J-Link di fascia superiore.\u003c\/li\u003e\n  \u003cli\u003eNessun trace ETM (usate SEGGER J-Trace) e nessuna interfaccia target QSPI.\u003c\/li\u003e\n  \u003cli\u003eVCOM è disponibile solo durante il debug via SWD ed è disattivato alla consegna: attivatelo in J-Link Configurator o J-Link Commander, quindi spegnete e riaccendete la sonda.\u003c\/li\u003e\n  \u003cli\u003eSolo USB, senza Ethernet. Per il montaggio all'interno di un'attrezzatura di collaudo, la BASE Compact ha due fori di fissaggio in un contenitore quadrato da 46mm.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eJ-Link BASE Classic a confronto con i modelli correlati\u003c\/h2\u003e\n\u003cdiv style=\"overflow-x:auto\"\u003e\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eModello\u003c\/th\u003e\n\u003cth\u003eFormato\u003c\/th\u003e\n\u003cth\u003eConnettore host\u003c\/th\u003e\n\u003cth\u003eJ-Flash, Ozone, Unlimited Flash Breakpoints\u003c\/th\u003e\n\u003cth\u003ePrezzo IVA esclusa\u003c\/th\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eJ-Link BASE Classic (questo prodotto)\u003c\/td\u003e\n\u003ctd\u003e100 x 53 x 27mm, 70g\u003c\/td\u003e\n\u003ctd\u003eUSB Type B\u003c\/td\u003e\n\u003ctd\u003eNon inclusi\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-8-08-00-j-link-base-classic\"\u003e£470\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-8-19-00-j-link-base-compact-debugger\"\u003eJ-Link BASE Compact\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e46 x 46 x 17mm, 20g, due fori di fissaggio\u003c\/td\u003e\n\u003ctd\u003eUSB-C\u003c\/td\u003e\n\u003ctd\u003eNon inclusi\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-8-19-00-j-link-base-compact-debugger\"\u003e£470\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-8-02-28-j-link-plus-classic-debugger\"\u003eJ-Link PLUS Classic\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e100 x 53 x 27mm, 70g\u003c\/td\u003e\n\u003ctd\u003eUSB Type B\u003c\/td\u003e\n\u003ctd\u003eInclusi\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-8-02-28-j-link-plus-classic-debugger\"\u003e£660\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/j-link-upgrade-base-to-plus\"\u003eJ-Link Upgrade BASE to PLUS\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eLicenza per una BASE esistente\u003c\/td\u003e\n\u003ctd\u003en\/d\u003c\/td\u003e\n\u003ctd\u003eLi aggiunge\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"j-link-upgrade-base-to-plus\"\u003e£320\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003c\/div\u003e\n\n\u003ch2\u003eApplicazioni tipiche\u003c\/h2\u003e\n\u003cp\u003eDownload in Flash e debug a livello di sorgente di componenti Cortex-M STM32, NXP LPC e Kinetis da STM32CubeIDE o MCUXpresso. Log RTT da un target senza UART libera durante il bring-up del firmware.\u003c\/p\u003e\n\u003cp\u003eScegliete la Classic per il banco; per un'attrezzatura di collaudo o un contenitore, la Compact offre le stesse funzioni in un contenitore quadrato da 46mm.\u003c\/p\u003e\n\n\u003cp\u003eOrdinate la J-Link BASE Classic a \u003cspan data-ds-price=\"segger-8-08-00-j-link-base-classic\"\u003e£470\u003c\/span\u003e IVA esclusa. Verificate il vostro codice componente nell'elenco dei dispositivi supportati da SEGGER, oppure richiedeteci un'offerta formale. Scoprite la gamma completa nella nostra collezione \u003ca href=\"\/it\/collections\/segger-debugger-catalogue-uk\"\u003esonde di debug SEGGER\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003cp\u003e\u003csmall\u003eUltima revisione: 16\/11\/2026.\u003c\/small\u003e\u003c\/p\u003e\n\u003cdetails\u003e\u003csummary\u003e\u003csmall\u003eFonti (5 pagine del produttore)\u003c\/small\u003e\u003c\/summary\u003e\u003cul\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/debug-probes\/j-link\/models\/j-link-base\/\"\u003ePagina prodotto SEGGER J-Link BASE\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/J-Link_BASE\"\u003eSEGGER Knowledge Base: J-Link BASE\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/purchase\/pricing\/jlink-related\/\"\u003ePrezzi e licenze SEGGER J-Link\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/Using_J-Link_VCOM_functionality\"\u003eSEGGER Knowledge Base: uso della funzione VCOM di J-Link\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/Supported_IDEs\"\u003eSEGGER Knowledge Base: IDE supportati\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/details\u003e","brand":"SEGGER Microcontroller GmbH","offers":[{"title":"Default Title","offer_id":44263172079839,"sku":"8.08.00","price":470.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0522\/6931\/8333\/files\/segger-microcontroller-gmbh-8-08-00-40212524663007.jpg?v=1689508389"},{"product_id":"segger-j-link-plus-compact-8-19-28","title":"SEGGER J-Link PLUS Compact (8.19.28)","description":"\u003cp\u003eLa SEGGER J-Link PLUS Compact (codice 8.19.28) è una sonda di debug JTAG\/SWD alimentata via USB in un contenitore da 46mm x 46mm x 17mm, con interfaccia target da 1.2V a 5V, velocità dell'interfaccia target fino a 15 MHz e velocità di download fino a 1 MB\/s. Offre lo stesso set di funzioni J-Link PLUS del modello desktop Classic, incluse le licenze per J-Flash, Unlimited Flash Breakpoints, Ozone e RDI, con porta host USB-C e due fori di fissaggio. È adatta a fixture di test, banchi automatici e stazioni di produzione che richiedono debug e programmazione della flash su target ARM Cortex, RISC-V, Renesas RX e Microchip PIC32.\u003c\/p\u003e\n\n\u003ch2\u003eSonda di debug JTAG\/SWD compatta per fixture e banchi\u003c\/h2\u003e\n\u003cp\u003eCon 20g di peso, 46mm di lato e due fori di fissaggio, la PLUS Compact può essere collocata all'interno di contenitori di apparecchiature esistenti, maschere di collaudo e banchi automatici. Il collegamento host è USB 2.0 Hi-Speed su USB-C e la sonda è alimentata da USB. Sul lato target utilizza il connettore standard J-Link a 20 pin da 0.1\"; le assegnazioni dei pin e gli adattatori disponibili sono nella nostra guida \u003ca href=\"\/it\/pages\/segger-j-link-20-pin-connector-pinout\"\u003epinout del connettore SEGGER J-Link a 20 pin\u003c\/a\u003e. La sonda può alimentare il target con 5V fino a 300mA prelevati dalla linea USB.\u003c\/p\u003e\n\n\u003ch2\u003eLicenze J-Link PLUS incluse sulla sonda\u003c\/h2\u003e\n\u003cp\u003eLa licenza J-Flash è preinstallata sulla sonda, quindi non c'è nulla da attivare. J-Flash programma la flash interna ed esterna senza un IDE. Unlimited Flash Breakpoints consente di impostare breakpoint in flash oltre il numero di breakpoint hardware disponibili nel core. Ozone, il debugger standalone di SEGGER, e la licenza RDI completano il pacchetto. Il debug in monitor mode è supportato sui core ARMv7-M e ARMv8-M.\u003c\/p\u003e\n\n\u003ch2\u003eCore supportati, RTT e VCOM\u003c\/h2\u003e\n\u003cp\u003eLe interfacce di debug supportate sono JTAG, cJTAG, SWD, SWD multi-drop, SWO, SPI, Microchip ICSP, Renesas FINE e Silicon Labs C2. L'elenco dei core supportati da SEGGER per J-Link PLUS comprende ARM da Cortex-M0 a Cortex-M85, Cortex-A e Cortex-R, i core ARM di generazioni precedenti da ARM7 a ARM11, core RISC-V di SiFive, Andes, Codasip e Nuclei, Renesas RX, Microchip PIC32, Silicon Labs EFM8 e Cadence Tensilica Xtensa. Real Time Transfer (RTT) trasferisce dati tra il target in esecuzione e l'host attraverso il collegamento di debug. Dove è disponibile una UART, VCOM la collega a una porta COM virtuale tramite i pin 5 (J-Link Tx) e 17 (J-Link Rx) del connettore a 20 pin, durante il debug in SWD.\u003c\/p\u003e\n\n\u003ch2\u003eSoftware e compatibilità con gli IDE\u003c\/h2\u003e\n\u003cp\u003eIl software J-Link è gratuito. Funziona su Windows (x86-64 e ARM64), Linux (x86-64 e ARM64) e macOS (x86-64 e Apple Silicon). SEGGER indica il supporto, tra gli altri, in SEGGER Embedded Studio, Eclipse, IAR EWARM, Keil MDK-ARM, STM32CubeIDE, MCUXpresso e Visual Studio Code.\u003c\/p\u003e\n\n\u003ch2\u003eContenuto della confezione\u003c\/h2\u003e\n\u003cp\u003eSonda J-Link PLUS Compact, cavo piatto a 20 pin da 0.1\" e cavo USB-C.\u003c\/p\u003e\n\n\u003ch2\u003eSpecifiche\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eInterfaccia host\u003c\/th\u003e\n\u003ctd\u003eUSB 2.0 Hi-Speed, USB-C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eConnettore target\u003c\/th\u003e\n\u003ctd\u003eJTAG\/SWD a 20 pin, 0.1\" (2.54mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eInterfacce di debug supportate\u003c\/th\u003e\n\u003ctd\u003eJTAG, cJTAG, SWD, SWD multi-drop, SWO, SPI, Microchip ICSP, Renesas FINE, Silicon Labs C2\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTensione dell'interfaccia target (VIF)\u003c\/th\u003e\n\u003ctd\u003eDa 1.2V a 5V\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eCorrente assorbita da VTref\u003c\/th\u003e\n\u003ctd\u003eMeno di 25µA\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eAlimentazione del target\u003c\/th\u003e\n\u003ctd\u003e5V (derivati da USB), max. 300mA\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eVelocità dell'interfaccia target\u003c\/th\u003e\n\u003ctd\u003eMax. 15 MHz\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eFrequenza di campionamento SWO\u003c\/th\u003e\n\u003ctd\u003eMax. 30 MHz\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eVelocità di download\u003c\/th\u003e\n\u003ctd\u003eFino a 1 MB\/s\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eAlimentazione\u003c\/th\u003e\n\u003ctd\u003eAlimentazione da USB, max. 50mA più la corrente di alimentazione del target\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eLicenze incluse\u003c\/th\u003e\n\u003ctd\u003eJ-Flash (preinstallata), Unlimited Flash Breakpoints, Ozone, RDI\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDimensioni (senza cavi)\u003c\/th\u003e\n\u003ctd\u003e46mm x 46mm x 17mm\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePeso (senza cavi)\u003c\/th\u003e\n\u003ctd\u003e20g\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTemperatura di esercizio\u003c\/th\u003e\n\u003ctd\u003eDa +5°C a +60°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTemperatura di stoccaggio\u003c\/th\u003e\n\u003ctd\u003eDa -20°C a +65°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eUmidità relativa\u003c\/th\u003e\n\u003ctd\u003eMax. 90% rH, senza condensa\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eEMC\u003c\/th\u003e\n\u003ctd\u003eEN 55022, EN 55024\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eSistema operativo host\u003c\/th\u003e\n\u003ctd\u003eWindows e Linux (x86-64, ARM64); macOS (x86-64, Apple Silicon)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eLimitazioni\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eSolo USB. Per l'accesso via Ethernet scelga la J-Link PRO, oppure la J-Link PRO PoE per il Power over Ethernet.\u003c\/li\u003e\n  \u003cli\u003eLa velocità di download arriva fino a 1 MB\/s e quella dell'interfaccia target fino a 15 MHz; i modelli J-Link ULTRA+ e PRO raggiungono fino a 4 MB\/s e 50 MHz.\u003c\/li\u003e\n  \u003cli\u003eNessun trace ETM su Cortex-M (usare SEGGER J-Trace) e nessuna interfaccia target QSPI.\u003c\/li\u003e\n  \u003cli\u003eVCOM è disponibile solo durante il debug in SWD.\u003c\/li\u003e\n  \u003cli\u003eSe serve solo il debug senza le licenze, la \u003ca href=\"\/it\/products\/segger-8-19-00-j-link-base-compact-debugger\"\u003eJ-Link BASE Compact\u003c\/a\u003e condivide lo stesso contenitore e le stesse specifiche hardware.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eJ-Link PLUS Compact a confronto con i modelli correlati\u003c\/h2\u003e\n\u003cdiv style=\"overflow-x:auto\"\u003e\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eModello\u003c\/th\u003e\n\u003cth\u003eFormato\u003c\/th\u003e\n\u003cth\u003eConnettore host\u003c\/th\u003e\n\u003cth\u003eVelocità di download\u003c\/th\u003e\n\u003cth\u003eJ-Flash, Ozone, Unlimited Flash Breakpoints\u003c\/th\u003e\n\u003cth\u003ePrezzo IVA esclusa\u003c\/th\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eJ-Link PLUS Compact (questo prodotto)\u003c\/td\u003e\n\u003ctd\u003e46 x 46 x 17mm, 20g, due fori di fissaggio\u003c\/td\u003e\n\u003ctd\u003eUSB-C\u003c\/td\u003e\n\u003ctd\u003eFino a 1 MB\/s\u003c\/td\u003e\n\u003ctd\u003eIncluse\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-j-link-plus-compact-8-19-28\"\u003e£660\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-8-02-28-j-link-plus-classic-debugger\"\u003eJ-Link PLUS Classic\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e100 x 53 x 27mm, 70g\u003c\/td\u003e\n\u003ctd\u003eUSB Type B\u003c\/td\u003e\n\u003ctd\u003eFino a 1 MB\/s\u003c\/td\u003e\n\u003ctd\u003eIncluse\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-8-02-28-j-link-plus-classic-debugger\"\u003e£660\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-8-19-00-j-link-base-compact-debugger\"\u003eJ-Link BASE Compact\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e46 x 46 x 17mm, 20g, due fori di fissaggio\u003c\/td\u003e\n\u003ctd\u003eUSB-C\u003c\/td\u003e\n\u003ctd\u003eFino a 1 MB\/s\u003c\/td\u003e\n\u003ctd\u003eNon incluse\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-8-19-00-j-link-base-compact-debugger\"\u003e£470\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-j-link-ultra-plus-8-16-28\"\u003eJ-Link ULTRA+ (J-Link Ultra)\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e72 x 45 x 18mm, 40g\u003c\/td\u003e\n\u003ctd\u003eUSB-C\u003c\/td\u003e\n\u003ctd\u003eFino a 4 MB\/s\u003c\/td\u003e\n\u003ctd\u003eIncluse\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-j-link-ultra-plus-8-16-28\"\u003e£870\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003c\/div\u003e\n\n\u003ch2\u003eApplicazioni tipiche\u003c\/h2\u003e\n\u003cp\u003eUna sonda fissata all'interno di una maschera di collaudo, che programma con J-Flash schede STM32 o NXP Kinetis alla fine di una linea pilota. Debug a livello di sorgente di codice Cortex-M eseguito dalla flash, con più breakpoint di quanti ne offra l'FPB del Cortex-M, su un banco dove la sonda resta montata.\u003c\/p\u003e\n\u003cp\u003eScelga la Compact per una fixture o un contenitore; per il banco di lavoro, la PLUS Classic offre le stesse funzioni in un contenitore più grande.\u003c\/p\u003e\n\n\u003cp\u003eOrdini la J-Link PLUS Compact a \u003cspan data-ds-price=\"segger-j-link-plus-compact-8-19-28\"\u003e£660\u003c\/span\u003e IVA esclusa. Verifichi il codice del suo dispositivo nell'elenco dei dispositivi supportati da SEGGER, oppure ci chieda un preventivo formale. Veda l'intera gamma nella nostra collezione \u003ca href=\"\/it\/collections\/segger-debugger-catalogue-uk\"\u003esonde di debug SEGGER\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003cp\u003e\u003csmall\u003eUltima revisione: 16 novembre 2026.\u003c\/small\u003e\u003c\/p\u003e\n\u003cdetails\u003e\u003csummary\u003e\u003csmall\u003eFonti (6 pagine del produttore)\u003c\/small\u003e\u003c\/summary\u003e\u003cul\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/debug-probes\/j-link\/models\/j-link-plus\/\"\u003ePagina prodotto SEGGER J-Link PLUS\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/J-Link_PLUS\"\u003eSEGGER Knowledge Base: J-Link PLUS\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/purchase\/pricing\/jlink-related\/\"\u003ePrezzi e licenze SEGGER J-Link\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/debug-probes\/j-link\/models\/j-link-ultra\/\"\u003ePagina prodotto SEGGER J-Link Ultra\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/Using_J-Link_VCOM_functionality\"\u003eSEGGER Knowledge Base: utilizzo della funzionalità VCOM di J-Link\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/Supported_IDEs\"\u003eSEGGER Knowledge Base: IDE supportati\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/details\u003e","brand":"SEGGER Microcontroller GmbH","offers":[{"title":"Default Title","offer_id":44263172112607,"sku":"8.19.28","price":660.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0522\/6931\/8333\/files\/segger-microcontroller-gmbh-8-19-28-40212529381599.jpg?v=1689508757"},{"product_id":"segger-8-19-00-j-link-base-compact-debugger","title":"SEGGER J-Link BASE Compact Debug Probe","description":"\u003cp\u003eThe SEGGER J-Link BASE Compact (part number 8.19.00) is a USB-powered JTAG\/SWD debug probe in a 46mm x 46mm x 17mm housing, with a 1.2V to 5V target interface, up to 15 MHz target interface speed and download speeds up to 1 MB\/s. It has the same J-Link BASE feature set as the desktop Classic model, with a USB-C host port and two mounting holes so it can stay inside a test fixture or end equipment. It suits firmware bring-up on ARM Cortex, RISC-V, Renesas RX and Microchip PIC32 targets, and fixed debug or programming stations where a full-size probe will not fit.\u003c\/p\u003e\n\n\u003ch2\u003eCompact JTAG\/SWD Debug Probe Built for Fixtures\u003c\/h2\u003e\n\u003cp\u003eAt 20g and 46mm square, with two mounting holes, the Compact is built to be fixed inside equipment housings, test jigs and development systems. The host link is USB 2.0 Hi-Speed over USB-C, and the probe is USB powered. On the target side it uses the standard J-Link 20-pin 0.1\" connector found on most J-Link models. Pin assignments and adapter options are in our \u003ca href=\"\/it\/pages\/segger-j-link-20-pin-connector-pinout\"\u003eSEGGER J-Link 20-pin connector pinout\u003c\/a\u003e guide.\u003c\/p\u003e\n\n\u003ch2\u003eTarget Interfaces and Supported Cores\u003c\/h2\u003e\n\u003cp\u003eCurrent J-Link BASE hardware supports JTAG, cJTAG, SWD, SWD multi-drop, SWO, SPI, Microchip ICSP, Renesas FINE and Silicon Labs C2. SEGGER's supported cores list covers ARM Cortex-M0 to Cortex-M85, Cortex-A and Cortex-R, legacy ARM7 to ARM1176, RISC-V cores from SiFive, Andes, Codasip and Nuclei, Renesas RX, Microchip PIC32 and Silicon Labs EFM8. The probe can also supply the target with 5V at up to 300mA from the USB rail.\u003c\/p\u003e\n\n\u003ch2\u003eRTT, VCOM and Trace Buffer Support\u003c\/h2\u003e\n\u003cp\u003eSEGGER Real Time Transfer (RTT) moves data between the running target and the host through the debug connection, so you can log or interact with an application without a spare UART. Where a UART is available, the VCOM function bridges it to a virtual COM port on the PC using pins 5 (J-Link Tx) and 17 (J-Link Rx) of the 20-pin connector; VCOM works only when debugging over SWD. Embedded Trace Buffer (ETB) and Micro Trace Buffer (MTB) are supported where the target implements them.\u003c\/p\u003e\n\n\u003ch2\u003eSoftware and IDE Compatibility\u003c\/h2\u003e\n\u003cp\u003eThe J-Link software and firmware updates are free. Setup and control software runs on Windows (x86-64 and ARM64), Linux (x86-64 and ARM64) and macOS (x86-64 and Apple Silicon). SEGGER lists full support in SEGGER Embedded Studio, Eclipse, IAR EWARM, Keil MDK-ARM, STM32CubeIDE, MCUXpresso and Visual Studio Code, among others. Several J-Links can run from one PC, each identified by its serial number.\u003c\/p\u003e\n\n\u003ch2\u003eWhat Is in the Box\u003c\/h2\u003e\n\u003cp\u003eJ-Link BASE Compact probe, 20-pin 0.1\" ribbon cable and a USB-C cable. No adapter for 10-pin 0.05\" Cortex Debug headers is included.\u003c\/p\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eHost interface\u003c\/th\u003e\n\u003ctd\u003eUSB 2.0 Hi-Speed, USB-C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget interface\u003c\/th\u003e\n\u003ctd\u003eJTAG\/SWD 20-pin, 0.1\" (2.54mm)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eSupported debug interfaces\u003c\/th\u003e\n\u003ctd\u003eJTAG, cJTAG, SWD, SWD multi-drop, SWO, SPI, Microchip ICSP, Renesas FINE, Silicon Labs C2\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget interface voltage (VIF)\u003c\/th\u003e\n\u003ctd\u003e1.2V to 5V\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget supply\u003c\/th\u003e\n\u003ctd\u003e5V (derived from USB), max. 300mA\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget interface speed\u003c\/th\u003e\n\u003ctd\u003eMax. 15 MHz\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eSWO sampling frequency\u003c\/th\u003e\n\u003ctd\u003eMax. 30 MHz\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDownload speed\u003c\/th\u003e\n\u003ctd\u003eUp to 1 MB\/s\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePower supply\u003c\/th\u003e\n\u003ctd\u003eUSB powered, max. 50mA plus target supply current\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDimensions (without cables)\u003c\/th\u003e\n\u003ctd\u003e46mm x 46mm x 17mm\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eWeight (without cables)\u003c\/th\u003e\n\u003ctd\u003e20g\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eOperating temperature\u003c\/th\u003e\n\u003ctd\u003e+5°C to +60°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eStorage temperature\u003c\/th\u003e\n\u003ctd\u003e-20°C to +65°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eRelative humidity\u003c\/th\u003e\n\u003ctd\u003eMax. 90% rH, non-condensing\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eEMC\u003c\/th\u003e\n\u003ctd\u003eEN 55022, EN 55024\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eHost OS\u003c\/th\u003e\n\u003ctd\u003eWindows and Linux (x86-64, ARM64); macOS (x86-64, Apple Silicon)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eLimitations\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eJ-Flash and J-Flash SPI, Unlimited Flash Breakpoints, the Ozone debugger and the RDI licence pack are not included, and SEGGER lists monitor-mode debugging under the PLUS upgrade. They come with the J-Link PLUS, or with the BASE to PLUS upgrade licence for an existing BASE.\u003c\/li\u003e\n  \u003cli\u003eDownload speed is up to 1 MB\/s; SEGGER quotes up to 4 MB\/s for higher-tier J-Link models.\u003c\/li\u003e\n  \u003cli\u003eNo ETM trace (use SEGGER J-Trace) and no QSPI target interface.\u003c\/li\u003e\n  \u003cli\u003eVCOM is available only when debugging over SWD.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eJ-Link BASE Compact Compared with Related Models\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eForm factor\u003c\/th\u003e\n\u003cth\u003eHost connector\u003c\/th\u003e\n\u003cth\u003eJ-Flash, Ozone, Unlimited Flash Breakpoints\u003c\/th\u003e\n\u003cth\u003ePrice ex VAT\u003c\/th\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eJ-Link BASE Compact (this product)\u003c\/td\u003e\n\u003ctd\u003e46 x 46 x 17mm, 20g, two mounting holes\u003c\/td\u003e\n\u003ctd\u003eUSB-C\u003c\/td\u003e\n\u003ctd\u003eNot included\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-8-19-00-j-link-base-compact-debugger\"\u003e£470\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-8-08-00-j-link-base-classic\"\u003eJ-Link BASE Classic\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e100 x 53 x 27mm, 70g\u003c\/td\u003e\n\u003ctd\u003eUSB Type B\u003c\/td\u003e\n\u003ctd\u003eNot included\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-8-08-00-j-link-base-classic\"\u003e£470\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-j-link-plus-compact-8-19-28\"\u003eJ-Link PLUS Compact\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e46 x 46 x 17mm, two mounting holes\u003c\/td\u003e\n\u003ctd\u003eUSB\u003c\/td\u003e\n\u003ctd\u003eIncluded\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-j-link-plus-compact-8-19-28\"\u003e£660\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/j-link-upgrade-base-to-plus\"\u003eJ-Link Upgrade BASE to PLUS\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eLicence for an existing BASE\u003c\/td\u003e\n\u003ctd\u003en\/a\u003c\/td\u003e\n\u003ctd\u003eAdds them\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"j-link-upgrade-base-to-plus\"\u003e£320\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eTypical Applications\u003c\/h2\u003e\n\u003cp\u003eFlash download and source-level debug of STM32, NXP LPC and Kinetis Cortex-M parts from STM32CubeIDE or MCUXpresso. A probe fixed inside a test jig, wired to a 20-pin header, for repeat debug access to Cortex-M33 or RISC-V boards in validation. RTT logging from a target with no free UART during firmware bring-up.\u003c\/p\u003e\n\u003cp\u003eChoose the Compact for a fixture or enclosure; for the bench, the Classic carries the same feature set in a larger housing.\u003c\/p\u003e\n\n\u003cp\u003eOrder the J-Link BASE Compact for \u003cspan data-ds-price=\"segger-8-19-00-j-link-base-compact-debugger\"\u003e£470\u003c\/span\u003e ex VAT. Check your part number against SEGGER's supported devices list, or ask us for a formal quotation. See the full range in our \u003ca href=\"\/it\/collections\/segger-debugger-catalogue-uk\"\u003eSEGGER debug probes\u003c\/a\u003e collection.\u003c\/p\u003e\n\n\u003cp\u003e\u003csmall\u003eLast reviewed 30\/10\/2026.\u003c\/small\u003e\u003c\/p\u003e\n\u003cdetails\u003e\u003csummary\u003e\u003csmall\u003eSources (4 manufacturer pages)\u003c\/small\u003e\u003c\/summary\u003e\u003cul\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/debug-probes\/j-link\/models\/j-link-base\/\"\u003eSEGGER J-Link BASE product page\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/J-Link_BASE\"\u003eSEGGER Knowledge Base: J-Link BASE\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/Using_J-Link_VCOM_functionality\"\u003eSEGGER Knowledge Base: Using J-Link VCOM functionality\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/Supported_IDEs\"\u003eSEGGER Knowledge Base: Supported IDEs\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/details\u003e","brand":"SEGGER Microcontroller GmbH","offers":[{"title":"Default Title","offer_id":44263172145375,"sku":"8.19.00","price":470.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0522\/6931\/8333\/files\/segger-microcontroller-gmbh-8-19-00-40212528234719.jpg?v=1689509458"},{"product_id":"segger-j-trace-pro-cortex-debugger","title":"SEGGER J-Trace PRO Cortex Trace Debugger","description":"\u003cp\u003eThe SEGGER J-Trace PRO Cortex (part number 8.20.00) is a streaming trace probe for ARM Cortex-A, Cortex-R and Cortex-M devices, with ETM and PTM trace, a USB 3.0 SuperSpeed and Gigabit Ethernet host link, download speeds up to 4.0 MB\/s and a 1.2V to 5V target interface. It combines J-Link debugging with unlimited instruction trace, live code coverage and live code profiling. It suits firmware teams working across Cortex-A, Cortex-R and Cortex-M targets.\u003c\/p\u003e\n\n\u003ch2\u003eStreaming Trace for Cortex-A, Cortex-R and Cortex-M\u003c\/h2\u003e\n\u003cp\u003eStreaming trace sends data continuously to the PC instead of stopping when a buffer fills, so a recording can run long enough to catch a rare fault or a program that ends up stuck in a fault handler. SEGGER's Knowledge Base lists ETM, PTM and ETB trace for ARM Cortex on this model. The supported cores list covers Cortex-A5 to Cortex-A17, Cortex-A53, A55, A57, A72 and A76, Cortex-R4, R5, R8, R52 and R82, Cortex-M0 to Cortex-M85, and SC000 and SC300. RISC-V is not supported; use the J-Trace PRO or J-Trace PRO RISC-V for those targets.\u003c\/p\u003e\n\n\u003ch2\u003eDebug and Trace Connectors\u003c\/h2\u003e\n\u003cp\u003eThe probe has two target connectors: the 20-pin JTAG\/SWD connector used across the J-Link range, with a 14-pin adapter available, and a 19-pin 0.05\" JTAG\/SWD and Trace connector that carries the trace clock and four trace data lines. Targets with a 38-pin Mictor header connect through the \u003ca href=\"\/it\/products\/segger-8-06-21-j-trace-mictor-38-adapter\"\u003eJ-Trace Mictor 38 Adapter\u003c\/a\u003e. Pin assignments for the 20-pin connector are in our \u003ca href=\"\/it\/pages\/segger-j-link-20-pin-connector-pinout\"\u003eSEGGER J-Link 20-pin connector pinout\u003c\/a\u003e guide. Supported debug interfaces are JTAG, cJTAG, SWD, SWD multi-drop and SWO, and the probe can supply 5V to the target.\u003c\/p\u003e\n\n\u003ch2\u003eFull J-Link PRO Debug Capability\u003c\/h2\u003e\n\u003cp\u003eJ-Trace PRO Cortex is also a complete J-Link. It includes the full set of J-Link PRO licences, including Unlimited Flash Breakpoints, and supports Real Time Transfer (RTT) and monitor-mode debugging on ARMv7-M and ARMv8-M. SEGGER allows Ozone, its debugger and trace analysis tool, to be used free of charge with a J-Trace PRO, including for commercial use. Ozone is SEGGER's recommended tool for trace analysis; debugging works from any J-Link compatible IDE. Software runs on Windows, Linux and macOS, including ARM64 and Apple Silicon hosts.\u003c\/p\u003e\n\u003cp\u003eThe Ethernet data lines are isolated to IEEE 802.3 (1500 Vrms for one minute). The shield is not, so SEGGER recommends an unshielded twisted pair cable where that isolation matters.\u003c\/p\u003e\n\n\u003ch2\u003eWhat's Included\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eJ-Trace PRO Cortex probe\u003c\/li\u003e\n  \u003cli\u003eCortex-M Trace Reference Board\u003c\/li\u003e\n  \u003cli\u003e20-pin 0.05\" target ribbon cable\u003c\/li\u003e\n  \u003cli\u003e20-pin 0.1\" target ribbon cable\u003c\/li\u003e\n  \u003cli\u003eMicro USB cable\u003c\/li\u003e\n  \u003cli\u003eUSB 3.0 cable\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eHost interface\u003c\/th\u003e\n\u003ctd\u003eUSB 3.0 SuperSpeed; Gigabit Ethernet\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget interface\u003c\/th\u003e\n\u003ctd\u003eJTAG\/SWD 20-pin (14-pin adapter available); JTAG\/SWD + Trace 19-pin 0.05\" (38-pin Mictor adapter available)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTrace\u003c\/th\u003e\n\u003ctd\u003eStreaming trace; ETM, PTM and ETB (ARM Cortex)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eSupported cores\u003c\/th\u003e\n\u003ctd\u003eARM Cortex-A, Cortex-R, Cortex-M, SC000, SC300\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget interface voltage (VIF)\u003c\/th\u003e\n\u003ctd\u003e1.2V to 5V\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget interface speed\u003c\/th\u003e\n\u003ctd\u003eMax. 50 MHz\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDownload speed\u003c\/th\u003e\n\u003ctd\u003eUp to 4.0 MB\/s\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePower supply\u003c\/th\u003e\n\u003ctd\u003eUSB powered, max. 400mA\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eReset type\u003c\/th\u003e\n\u003ctd\u003eOpen drain with 100 Ohm series resistor, can be pulled low or tristated\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTrace capacitive load\u003c\/th\u003e\n\u003ctd\u003e3 pF J-Trace plus 8 pF cable (typical)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDimensions (without cables)\u003c\/th\u003e\n\u003ctd\u003e123mm x 68mm x 30mm\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eWeight (without cables)\u003c\/th\u003e\n\u003ctd\u003e120g\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eOperating temperature\u003c\/th\u003e\n\u003ctd\u003e+5°C to +60°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eStorage temperature\u003c\/th\u003e\n\u003ctd\u003e-20°C to +65°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eRelative humidity\u003c\/th\u003e\n\u003ctd\u003eMax. 90% rH, non-condensing\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eEMC\u003c\/th\u003e\n\u003ctd\u003eEN 55022, EN 55024\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eHost OS\u003c\/th\u003e\n\u003ctd\u003eWindows and Linux (x86-64, ARM64); macOS (x86-64, Apple Silicon)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eLimitations\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eNo RISC-V support; choose the J-Trace PRO or the J-Trace PRO RISC-V.\u003c\/li\u003e\n  \u003cli\u003eTrace needs the target to implement trace hardware and bring the trace pins out to a connector; SEGGER notes that trace setup depends on the target hardware design.\u003c\/li\u003e\n  \u003cli\u003eNo VCOM and no CMSIS-DAP v1 (HID) mode.\u003c\/li\u003e\n  \u003cli\u003eMost IDEs offer little or no trace analysis; plan on Ozone for coverage and profiling.\u003c\/li\u003e\n  \u003cli\u003eThe Mictor 38 adapter is a separate purchase.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eJ-Trace PRO Cortex Compared with the Other J-Trace PRO Models\u003c\/h2\u003e\n\u003cdiv style=\"overflow-x:auto\"\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eTrace architectures\u003c\/th\u003e\n\u003cth\u003eCortex-M Trace Reference Board in box\u003c\/th\u003e\n\u003cth\u003ePrice ex VAT\u003c\/th\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eJ-Trace PRO Cortex (this product)\u003c\/td\u003e\n\u003ctd\u003eARM Cortex-A, Cortex-R and Cortex-M\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-j-trace-pro-cortex-debugger\"\u003e£2,005\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-j-trace-pro-trace-probe\"\u003eJ-Trace PRO\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eARM Cortex-A, Cortex-R, Cortex-M and RISC-V\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-j-trace-pro-trace-probe\"\u003e£3,005\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-j-trace-pro-cortex-m-8-18-00\"\u003eJ-Trace PRO Cortex-M\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eARM Cortex-M\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-j-trace-pro-cortex-m-8-18-00\"\u003e£1,515\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-8-22-00-j-trace-pro-risc-v\"\u003eJ-Trace PRO RISC-V\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eRISC-V (RV32, RV64)\u003c\/td\u003e\n\u003ctd\u003eNot listed\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-8-22-00-j-trace-pro-risc-v\"\u003e£2,005\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTypical Applications\u003c\/h2\u003e\n\u003cp\u003ePTM trace on a Cortex-A9, or ETM trace on a Cortex-A53, application processor to follow program flow into a crash. ETM trace on a Cortex-R5 or Cortex-R52 real-time core to measure interrupt timing over a long run. Live code coverage on a Cortex-M4 or Cortex-M33 microcontroller to show which paths a test suite exercised.\u003c\/p\u003e\n\u003cp\u003eChoose the J-Trace PRO Cortex when your targets include Cortex-A or Cortex-R cores; for Cortex-M only work, compare the J-Trace PRO Cortex-M.\u003c\/p\u003e\n\n\u003cp\u003eOrder the J-Trace PRO Cortex for \u003cspan data-ds-price=\"segger-j-trace-pro-cortex-debugger\"\u003e£2,005\u003c\/span\u003e ex VAT. Check your device's trace pins, or ask us for a formal quotation. See the full range in our \u003ca href=\"\/it\/collections\/segger-debugger-catalogue-uk\"\u003eSEGGER debug probes\u003c\/a\u003e collection.\u003c\/p\u003e\n\n\u003cp\u003e\u003csmall\u003eLast reviewed 16\/11\/2026.\u003c\/small\u003e\u003c\/p\u003e\n\u003cdetails\u003e\u003csummary\u003e\u003csmall\u003eSources (5 manufacturer pages)\u003c\/small\u003e\u003c\/summary\u003e\u003cul\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/debug-probes\/j-trace\/models\/j-trace-cortex-arm\/\"\u003eSEGGER J-Trace PRO Cortex-A\/R\/M product page\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/J-Trace_PRO_Cortex\"\u003eSEGGER Knowledge Base: J-Trace PRO Cortex\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/19-pin_JTAG\/SWD_and_Trace_Connector\"\u003eSEGGER Knowledge Base: 19-pin JTAG\/SWD and Trace Connector\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/debug-probes\/j-trace\/\"\u003eSEGGER J-Trace model overview\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/purchase\/pricing\/jtrace\/\"\u003eSEGGER J-Trace pricing and part numbers\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/details\u003e","brand":"SEGGER Microcontroller GmbH","offers":[{"title":"Default Title","offer_id":44263172178143,"sku":"8.20.00","price":2005.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0522\/6931\/8333\/files\/segger-microcontroller-gmbh-8-20-00-40235997790431.jpg?v=1689939840"},{"product_id":"segger-j-trace-pro-cortex-m-8-18-00","title":"SEGGER J-Trace PRO Cortex-M Streaming Trace Debugger (8.18.00)","description":"\u003cp\u003eThe SEGGER J-Trace PRO Cortex-M (part number 8.18.00) is a streaming trace probe for ARM Cortex-M microcontrollers, from Cortex-M0 to Cortex-M85, with ETM trace, a USB 3.0 SuperSpeed and Gigabit Ethernet host link, download speeds up to 4.0 MB\/s and a 1.2V to 5V target interface. It combines J-Link debugging with unlimited instruction trace, live code coverage and live code profiling. It suits firmware teams chasing intermittent faults, measuring code coverage or profiling Cortex-M applications.\u003c\/p\u003e\n\n\u003ch2\u003eStreaming ETM Trace for Cortex-M Microcontrollers\u003c\/h2\u003e\n\u003cp\u003eStreaming trace sends data continuously to the PC instead of stopping when a buffer fills, so a recording can run long enough to catch a rare fault or a program that ends up stuck in a fault handler. SEGGER's Knowledge Base lists ETM and ETB trace for Cortex-M on this model. The supported cores list covers Cortex-M0, M0+, M1, M3, M4, M7, M23, M33, M52, M55 and M85, plus SC000 and SC300. Cortex-A and RISC-V cores are not supported.\u003c\/p\u003e\n\n\u003ch2\u003eDebug and Trace Connectors\u003c\/h2\u003e\n\u003cp\u003eThe probe has two target connectors: the 20-pin JTAG\/SWD connector used across the J-Link range, with a 14-pin adapter available, and a 19-pin 0.05\" JTAG\/SWD and Trace connector that carries the trace clock and four trace data lines. Targets with a 38-pin Mictor header connect through the \u003ca href=\"\/it\/products\/segger-8-06-21-j-trace-mictor-38-adapter\"\u003eJ-Trace Mictor 38 Adapter\u003c\/a\u003e. Pin assignments for the 20-pin connector are in our \u003ca href=\"\/it\/pages\/segger-j-link-20-pin-connector-pinout\"\u003eSEGGER J-Link 20-pin connector pinout\u003c\/a\u003e guide. Supported debug interfaces are JTAG, cJTAG, SWD, SWD multi-drop and SWO, and the probe can supply 5V to the target.\u003c\/p\u003e\n\n\u003ch2\u003eFull J-Link PRO Debug Capability\u003c\/h2\u003e\n\u003cp\u003eJ-Trace PRO Cortex-M is also a complete J-Link. It includes the full set of J-Link PRO licences, including Unlimited Flash Breakpoints, and supports Real Time Transfer (RTT) and monitor-mode debugging on ARMv7-M and ARMv8-M. SEGGER allows Ozone, its debugger and trace analysis tool, to be used free of charge with a J-Trace PRO, including for commercial use. Ozone is SEGGER's recommended tool for trace analysis; debugging works from any J-Link compatible IDE. Software runs on Windows, Linux and macOS, including ARM64 and Apple Silicon hosts.\u003c\/p\u003e\n\u003cp\u003eThe Ethernet data lines are isolated to IEEE 802.3 (1500 Vrms for one minute). The shield is not, so SEGGER recommends an unshielded twisted pair cable where that isolation matters.\u003c\/p\u003e\n\n\u003ch2\u003eWhat's Included\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eJ-Trace PRO Cortex-M probe\u003c\/li\u003e\n  \u003cli\u003eCortex-M Trace Reference Board\u003c\/li\u003e\n  \u003cli\u003e20-pin 0.05\" target ribbon cable\u003c\/li\u003e\n  \u003cli\u003e20-pin 0.1\" target ribbon cable\u003c\/li\u003e\n  \u003cli\u003eMicro USB cable\u003c\/li\u003e\n  \u003cli\u003eUSB 3.0 cable\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eHost interface\u003c\/th\u003e\n\u003ctd\u003eUSB 3.0 SuperSpeed; Gigabit Ethernet\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget interface\u003c\/th\u003e\n\u003ctd\u003eJTAG\/SWD 20-pin (14-pin adapter available); JTAG\/SWD + Trace 19-pin 0.05\"\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTrace\u003c\/th\u003e\n\u003ctd\u003eStreaming trace; ETM and ETB (Cortex-M)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eSupported cores\u003c\/th\u003e\n\u003ctd\u003eARM Cortex-M0 to Cortex-M85, SC000, SC300\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget interface voltage (VIF)\u003c\/th\u003e\n\u003ctd\u003e1.2V to 5V\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget interface speed\u003c\/th\u003e\n\u003ctd\u003eMax. 50 MHz\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDownload speed\u003c\/th\u003e\n\u003ctd\u003eUp to 4.0 MB\/s\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePower supply\u003c\/th\u003e\n\u003ctd\u003eUSB powered, max. 400mA\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eReset type\u003c\/th\u003e\n\u003ctd\u003eOpen drain with 100 Ohm series resistor, can be pulled low or tristated\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTrace capacitive load\u003c\/th\u003e\n\u003ctd\u003e3 pF J-Trace plus 8 pF cable (typical)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDimensions (without cables)\u003c\/th\u003e\n\u003ctd\u003e123mm x 68mm x 30mm\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eWeight (without cables)\u003c\/th\u003e\n\u003ctd\u003e120g\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eOperating temperature\u003c\/th\u003e\n\u003ctd\u003e+5°C to +60°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eStorage temperature\u003c\/th\u003e\n\u003ctd\u003e-20°C to +65°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eRelative humidity\u003c\/th\u003e\n\u003ctd\u003eMax. 90% rH, non-condensing\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eEMC\u003c\/th\u003e\n\u003ctd\u003eEN 55022, EN 55024\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eHost OS\u003c\/th\u003e\n\u003ctd\u003eWindows and Linux (x86-64, ARM64); macOS (x86-64, Apple Silicon)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eLimitations\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eCortex-M only. For Cortex-A or Cortex-R trace choose the J-Trace PRO Cortex; for RISC-V, the J-Trace PRO or J-Trace PRO RISC-V.\u003c\/li\u003e\n  \u003cli\u003eTrace needs the target to implement ETM and bring the trace pins out to a connector; SEGGER notes that trace setup depends on the target hardware design.\u003c\/li\u003e\n  \u003cli\u003eNo VCOM and no CMSIS-DAP v1 (HID) mode.\u003c\/li\u003e\n  \u003cli\u003eMost IDEs offer little or no trace analysis; plan on Ozone for coverage and profiling.\u003c\/li\u003e\n  \u003cli\u003eThe Mictor 38 adapter is a separate purchase.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eJ-Trace PRO Cortex-M Compared with the Other J-Trace PRO Models\u003c\/h2\u003e\n\u003cdiv style=\"overflow-x:auto\"\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eTrace architectures\u003c\/th\u003e\n\u003cth\u003eCortex-M Trace Reference Board in box\u003c\/th\u003e\n\u003cth\u003ePrice ex VAT\u003c\/th\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eJ-Trace PRO Cortex-M (this product)\u003c\/td\u003e\n\u003ctd\u003eARM Cortex-M\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-j-trace-pro-cortex-m-8-18-00\"\u003e£1,515\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-j-trace-pro-cortex-debugger\"\u003eJ-Trace PRO Cortex\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eARM Cortex-A, Cortex-R and Cortex-M\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-j-trace-pro-cortex-debugger\"\u003e£2,005\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-j-trace-pro-trace-probe\"\u003eJ-Trace PRO\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eARM Cortex-A, Cortex-R, Cortex-M and RISC-V\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-j-trace-pro-trace-probe\"\u003e£3,005\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-8-22-00-j-trace-pro-risc-v\"\u003eJ-Trace PRO RISC-V\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eRISC-V (RV32, RV64)\u003c\/td\u003e\n\u003ctd\u003eNot listed\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-8-22-00-j-trace-pro-risc-v\"\u003e£2,005\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTypical Applications\u003c\/h2\u003e\n\u003cp\u003eInstruction trace on an STM32H7 (Cortex-M7) or i.MX RT1050 board to find an intermittent hard fault after hours of running. Live code coverage on a Cortex-M33 design to show which code paths a test suite exercised. Live profiling of an RTOS application on a Cortex-M4 to find the functions using the most CPU time.\u003c\/p\u003e\n\u003cp\u003eChoose the J-Trace PRO Cortex-M when all your trace targets are Cortex-M microcontrollers.\u003c\/p\u003e\n\n\u003cp\u003eOrder the J-Trace PRO Cortex-M for \u003cspan data-ds-price=\"segger-j-trace-pro-cortex-m-8-18-00\"\u003e£1,515\u003c\/span\u003e ex VAT. Check your device's trace pins, or ask us for a formal quotation. See the full range in our \u003ca href=\"\/it\/collections\/segger-debugger-catalogue-uk\"\u003eSEGGER debug probes\u003c\/a\u003e collection.\u003c\/p\u003e\n\n\u003cp\u003e\u003csmall\u003eLast reviewed 16\/11\/2026.\u003c\/small\u003e\u003c\/p\u003e\n\u003cdetails\u003e\u003csummary\u003e\u003csmall\u003eSources (5 manufacturer pages)\u003c\/small\u003e\u003c\/summary\u003e\u003cul\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/debug-probes\/j-trace\/models\/j-trace\/\"\u003eSEGGER J-Trace PRO Cortex-M product page\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/J-Trace_PRO_Cortex-M\"\u003eSEGGER Knowledge Base: J-Trace PRO Cortex-M\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/19-pin_JTAG\/SWD_and_Trace_Connector\"\u003eSEGGER Knowledge Base: 19-pin JTAG\/SWD and Trace Connector\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/debug-probes\/j-trace\/accessories\/adapters\/j-trace-mictor-38-adapter\/\"\u003eSEGGER J-Trace Mictor 38 Adapter\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/purchase\/pricing\/jtrace\/\"\u003eSEGGER J-Trace pricing and part numbers\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/details\u003e","brand":"SEGGER Microcontroller GmbH","offers":[{"title":"Default Title","offer_id":44263172210911,"sku":"8.18.00","price":1515.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0522\/6931\/8333\/files\/segger-microcontroller-gmbh-8-18-00-40212539080927.jpg?v=1689509285"},{"product_id":"segger-8-22-00-j-trace-pro-risc-v","title":"SEGGER J-Trace PRO RISC-V Debug Probe","description":"\u003cp\u003eThe SEGGER J-Trace PRO RISC-V (part number 8.22.00) is a streaming trace probe for RV32 and RV64 RISC-V cores, using RISC-V N-Trace BTM, with a USB 3.0 SuperSpeed and Gigabit Ethernet host link, download speeds up to 4.0 MB\/s and a 1.2V to 5V target interface. It combines J-Link debugging with unlimited instruction trace, live code coverage and live code profiling. It suits firmware teams bringing up and validating RISC-V microcontrollers and SoCs that implement N-Trace.\u003c\/p\u003e\n\n\u003ch2\u003eStreaming N-Trace for RISC-V Cores\u003c\/h2\u003e\n\u003cp\u003eStreaming trace sends data continuously to the PC instead of stopping when a buffer fills, so a recording can run long enough to catch a rare fault or a program that ends up stuck in a fault handler. SEGGER's Knowledge Base lists N-Trace BTM for RISC-V and supported cores of RV32 and RV64 on this model. Devices without a SEGGER trace reference must implement the RISC-V trace components that SEGGER describes in its N-Trace documentation.\u003c\/p\u003e\n\n\u003ch2\u003eDebug and Trace Connectors\u003c\/h2\u003e\n\u003cp\u003eThe probe has two target connectors: the 20-pin JTAG\/SWD connector used across the J-Link range, with a 14-pin adapter available, and a 19-pin 0.05\" JTAG\/SWD and Trace connector that carries the trace clock and four trace data lines. Pin assignments for the 20-pin connector are in our \u003ca href=\"\/it\/pages\/segger-j-link-20-pin-connector-pinout\"\u003eSEGGER J-Link 20-pin connector pinout\u003c\/a\u003e guide. SEGGER's feature table for this model lists JTAG, cJTAG and SWD debug interfaces, and the probe can supply 5V to the target.\u003c\/p\u003e\n\n\u003ch2\u003eFull J-Link PRO Debug Capability\u003c\/h2\u003e\n\u003cp\u003eJ-Trace PRO RISC-V is also a full J-Link debug probe for RISC-V. It includes the full set of J-Link PRO licences, including Unlimited Flash Breakpoints. SEGGER allows Ozone, its debugger and trace analysis tool, to be used free of charge with a J-Trace PRO, including for commercial use. Ozone is SEGGER's recommended tool for trace analysis; debugging works from any J-Link compatible IDE. Software runs on Windows, Linux and macOS, including ARM64 and Apple Silicon hosts.\u003c\/p\u003e\n\u003cp\u003eThe Ethernet data lines are isolated to IEEE 802.3 (1500 Vrms for one minute). The shield is not, so SEGGER recommends an unshielded twisted pair cable where that isolation matters.\u003c\/p\u003e\n\n\u003ch2\u003eWhat's Included\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eJ-Trace PRO RISC-V probe\u003c\/li\u003e\n  \u003cli\u003e20-pin 0.05\" target ribbon cable\u003c\/li\u003e\n  \u003cli\u003e20-pin 0.1\" target ribbon cable\u003c\/li\u003e\n  \u003cli\u003eUSB 3.0 cable\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eHost interface\u003c\/th\u003e\n\u003ctd\u003eUSB 3.0 SuperSpeed; Gigabit Ethernet\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget interface\u003c\/th\u003e\n\u003ctd\u003eJTAG\/SWD 20-pin (14-pin adapter available); JTAG\/SWD + Trace 19-pin 0.05\"\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTrace\u003c\/th\u003e\n\u003ctd\u003eStreaming trace; N-Trace BTM (RISC-V)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eSupported cores\u003c\/th\u003e\n\u003ctd\u003eRISC-V RV32, RV64\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget interface voltage (VIF)\u003c\/th\u003e\n\u003ctd\u003e1.2V to 5V\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget interface speed\u003c\/th\u003e\n\u003ctd\u003eMax. 50 MHz\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDownload speed\u003c\/th\u003e\n\u003ctd\u003eUp to 4.0 MB\/s\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePower supply\u003c\/th\u003e\n\u003ctd\u003eUSB powered, max. 400mA\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eReset type\u003c\/th\u003e\n\u003ctd\u003eOpen drain with 100 Ohm series resistor, can be pulled low or tristated\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTrace capacitive load\u003c\/th\u003e\n\u003ctd\u003e3 pF J-Trace plus 8 pF cable (typical)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDimensions (without cables)\u003c\/th\u003e\n\u003ctd\u003e123mm x 68mm x 30mm\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eWeight (without cables)\u003c\/th\u003e\n\u003ctd\u003e120g\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eOperating temperature\u003c\/th\u003e\n\u003ctd\u003e+5°C to +60°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eStorage temperature\u003c\/th\u003e\n\u003ctd\u003e-20°C to +65°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eRelative humidity\u003c\/th\u003e\n\u003ctd\u003eMax. 90% rH, non-condensing\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eEMC\u003c\/th\u003e\n\u003ctd\u003eEN 55022, EN 55024\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eHost OS\u003c\/th\u003e\n\u003ctd\u003eWindows and Linux (x86-64, ARM64); macOS (x86-64, Apple Silicon)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eLimitations\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eRISC-V only. SEGGER's feature table for this model lists no ARM ETM, PTM or ETB trace, no SWO and no ARM monitor-mode debugging; for ARM and RISC-V in one probe, choose the J-Trace PRO.\u003c\/li\u003e\n  \u003cli\u003eNo SWD multi-drop, VCOM or CMSIS-DAP v1 (HID) mode.\u003c\/li\u003e\n  \u003cli\u003eTrace needs the target to implement N-Trace and bring the trace pins out to a connector; SEGGER notes that trace setup depends on the target hardware design.\u003c\/li\u003e\n  \u003cli\u003eSEGGER's package list for this model does not include the Cortex-M Trace Reference Board.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eJ-Trace PRO RISC-V Compared with the Other J-Trace PRO Models\u003c\/h2\u003e\n\u003cdiv style=\"overflow-x:auto\"\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eTrace architectures\u003c\/th\u003e\n\u003cth\u003eCortex-M Trace Reference Board in box\u003c\/th\u003e\n\u003cth\u003ePrice ex VAT\u003c\/th\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eJ-Trace PRO RISC-V (this product)\u003c\/td\u003e\n\u003ctd\u003eRISC-V (RV32, RV64)\u003c\/td\u003e\n\u003ctd\u003eNot listed\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-8-22-00-j-trace-pro-risc-v\"\u003e£2,005\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-j-trace-pro-trace-probe\"\u003eJ-Trace PRO\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eARM Cortex-A, Cortex-R, Cortex-M and RISC-V\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-j-trace-pro-trace-probe\"\u003e£3,005\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-j-trace-pro-cortex-debugger\"\u003eJ-Trace PRO Cortex\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eARM Cortex-A, Cortex-R and Cortex-M\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-j-trace-pro-cortex-debugger\"\u003e£2,005\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-j-trace-pro-cortex-m-8-18-00\"\u003eJ-Trace PRO Cortex-M\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eARM Cortex-M\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-j-trace-pro-cortex-m-8-18-00\"\u003e£1,515\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTypical Applications\u003c\/h2\u003e\n\u003cp\u003eInstruction trace on an RV32 microcontroller to find the code path that leads to an intermittent exception. Live code coverage on an RV64 core to show which paths a test suite exercised before release. Trace on a SiFive core bitstream on an ARTY board, connected through the \u003ca href=\"\/it\/products\/segger-8-06-35-sifive-arty-trace-adapter\"\u003eSiFive-ARTY Trace Adapter\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003eChoose the J-Trace PRO RISC-V when all your trace targets are RISC-V.\u003c\/p\u003e\n\n\u003cp\u003eOrder the J-Trace PRO RISC-V for \u003cspan data-ds-price=\"segger-8-22-00-j-trace-pro-risc-v\"\u003e£2,005\u003c\/span\u003e ex VAT. Check that your device implements N-Trace with the trace pins connected, or ask us for a formal quotation. See the full range in our \u003ca href=\"\/it\/collections\/segger-debugger-catalogue-uk\"\u003eSEGGER debug probes\u003c\/a\u003e collection.\u003c\/p\u003e\n\n\u003cp\u003e\u003csmall\u003eLast reviewed 16\/11\/2026.\u003c\/small\u003e\u003c\/p\u003e\n\u003cdetails\u003e\u003csummary\u003e\u003csmall\u003eSources (5 manufacturer pages)\u003c\/small\u003e\u003c\/summary\u003e\u003cul\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/debug-probes\/j-trace\/models\/j-trace-pro-risc-v\/\"\u003eSEGGER J-Trace PRO RISC-V product page\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/J-Trace_PRO_RISC-V\"\u003eSEGGER Knowledge Base: J-Trace PRO RISC-V\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/RISC-V_N-Trace\"\u003eSEGGER Knowledge Base: RISC-V N-Trace\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/19-pin_JTAG\/SWD_and_Trace_Connector\"\u003eSEGGER Knowledge Base: 19-pin JTAG\/SWD and Trace Connector\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/purchase\/pricing\/jtrace\/\"\u003eSEGGER J-Trace pricing and part numbers\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/details\u003e","brand":"SEGGER Microcontroller GmbH","offers":[{"title":"Default Title","offer_id":44263172243679,"sku":"8.22.00","price":2005.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0522\/6931\/8333\/files\/segger-microcontroller-gmbh-8-22-00-40212577452255.jpg?v=1689939145"},{"product_id":"segger-8-07-00-jtag-isolator-adapter","title":"SEGGER J-Link JTAG Isolator","description":"\u003cp\u003eThe SEGGER J-Link JTAG Isolator (part number 8.07.00) is an isolator box that sits between a J-Link or Flasher and the target, giving 1kV DC basic isolation on JTAG at up to 4 MHz for target interface voltages from 1.2V to 5V. Both sides use 20-pin 0.1\" male JTAG connectors; the isolator is powered from the probe side and draws less than 25µA on the target side. Use it where the debug or production tools do not share a ground with the application.\u003c\/p\u003e\n\n\u003ch2\u003eJTAG Isolation for Motor Control, Sensor and Analogue Designs\u003c\/h2\u003e\n\u003cp\u003eSEGGER describes isolation as essential when the development or production tools are not connected to the same ground as the application. Motor control applications tend to introduce electrical spikes, and the isolator keeps them away from the probe. In sensor and analogue designs, it keeps the debug system from disturbing the measurement. The isolator uses high-speed digital isolators and passes TRST, TDI, TMS, TCK, RTCK, TDO and RESET.\u003c\/p\u003e\n\u003cp\u003eProtection includes overvoltage and overcurrent protection on the probe side, overvoltage protection on the target VTref pin and ESD protection. Four LEDs show probe or programmer power, probe or programmer overload, target power and target RESET. On the target side, SEGGER's Knowledge Base lists pins 1 and 2 as VCC, through which the target side draws its power, with pins 17 and 19 not connected. See our \u003ca href=\"\/it\/pages\/segger-j-link-20-pin-connector-pinout\"\u003eSEGGER J-Link 20-pin connector pinout\u003c\/a\u003e guide for the probe side.\u003c\/p\u003e\n\n\u003ch2\u003eWhat's Included\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eJTAG Isolator Box\u003c\/li\u003e\n  \u003cli\u003e0.1\" 20-pin ribbon cable\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eIsolation\u003c\/th\u003e\n\u003ctd\u003e1kV DC, basic isolation\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget interface\u003c\/th\u003e\n\u003ctd\u003eJTAG\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget signals\u003c\/th\u003e\n\u003ctd\u003eTRST, TDI, TMS, TCK, RTCK, TDO, RESET\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eMax. target interface speed\u003c\/th\u003e\n\u003ctd\u003e4 MHz\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget interface voltage\u003c\/th\u003e\n\u003ctd\u003e1.2V to 5V\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eProbe-side connector\u003c\/th\u003e\n\u003ctd\u003e20-pin 0.1\" male JTAG\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget-side connector\u003c\/th\u003e\n\u003ctd\u003e20-pin 0.1\" male JTAG\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePower supply\u003c\/th\u003e\n\u003ctd\u003ePowered from the probe side\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget-side power consumption\u003c\/th\u003e\n\u003ctd\u003e\u0026lt;25µA\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDimensions (L x W x H)\u003c\/th\u003e\n\u003ctd\u003e73mm x 46mm x 19mm\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e38g\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eOperating temperature\u003c\/th\u003e\n\u003ctd\u003e+5°C to +60°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eStorage temperature\u003c\/th\u003e\n\u003ctd\u003e-20°C to +65°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eRelative humidity\u003c\/th\u003e\n\u003ctd\u003e\u0026lt;90% rH, non-condensing\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eCompatible J-Link models\u003c\/th\u003e\n\u003ctd\u003ePRO PoE, PRO, Ultra, WiFi, PLUS, BASE\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eCompatible Flasher models\u003c\/th\u003e\n\u003ctd\u003ePRO, PRO XL, Compact, Portable PLUS\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eLimitations\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eNo SWD and no cJTAG: the isolator does not support bidirectional transmission on SWDIO or TMSC. Use the SWD Isolator for SWD.\u003c\/li\u003e\n  \u003cli\u003eTarget interface speed is limited to 4 MHz.\u003c\/li\u003e\n  \u003cli\u003eBasic isolation only. Do not use it with hazardous voltages without a further protection measure such as double or reinforced isolation.\u003c\/li\u003e\n  \u003cli\u003eThird-party probes with the same pinout must supply 5V on pin 19; SEGGER states their use is at your own risk.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eJTAG Isolator Compared with Other SEGGER Isolators\u003c\/h2\u003e\n\u003cdiv style=\"overflow-x:auto\"\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eIsolator\u003c\/th\u003e\n\u003cth\u003eIsolated link\u003c\/th\u003e\n\u003cth\u003eIsolation\u003c\/th\u003e\n\u003cth\u003eMax. speed\u003c\/th\u003e\n\u003cth\u003ePrice ex VAT\u003c\/th\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eJTAG Isolator (this product)\u003c\/td\u003e\n\u003ctd\u003eProbe to target, JTAG, 20-pin 0.1\"\u003c\/td\u003e\n\u003ctd\u003e1kV DC, basic\u003c\/td\u003e\n\u003ctd\u003e4 MHz\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-8-07-00-jtag-isolator-adapter\"\u003e£226\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-8-07-01-swd-isolator-adapter\"\u003eSWD Isolator\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eProbe to target, SWD and SWO, 20-pin 0.1\"\u003c\/td\u003e\n\u003ctd\u003e1kV DC, basic\u003c\/td\u003e\n\u003ctd\u003e4 MHz\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-8-07-01-swd-isolator-adapter\"\u003e£240\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-8-07-02-usb-isolator-adapter\"\u003eUSB Isolator\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eHost PC to probe, USB\u003c\/td\u003e\n\u003ctd\u003e3kV DC for 1s, basic\u003c\/td\u003e\n\u003ctd\u003eUSB Full-Speed, 12 Mbit\/s\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-8-07-02-usb-isolator-adapter\"\u003e£185\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-8-07-10-j-trace-isolator-adapter\"\u003eJ-Trace Isolator\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eJ-Trace to target, JTAG, SWD, SWO and ETM trace, 19-pin 0.05\"\u003c\/td\u003e\n\u003ctd\u003e1kV DC, basic\u003c\/td\u003e\n\u003ctd\u003e4 MHz debug, 75 MHz trace clock\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-8-07-10-j-trace-isolator-adapter\"\u003e£320\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\n\u003cp\u003eOrder the JTAG Isolator for \u003cspan data-ds-price=\"segger-8-07-00-jtag-isolator-adapter\"\u003e£226\u003c\/span\u003e ex VAT. Confirm that your target debugs over JTAG at 4 MHz or below, or ask us for a formal quotation. See the full range in our \u003ca href=\"\/it\/collections\/segger-debugger-catalogue-uk\"\u003eSEGGER debug probes\u003c\/a\u003e collection.\u003c\/p\u003e\n\n\u003cp\u003e\u003csmall\u003eLast reviewed 16\/11\/2026.\u003c\/small\u003e\u003c\/p\u003e\n\u003cdetails\u003e\u003csummary\u003e\u003csmall\u003eSources (5 manufacturer pages)\u003c\/small\u003e\u003c\/summary\u003e\u003cul\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/debug-probes\/j-link\/accessories\/isolators\/j-link-jtag-isolator\/\"\u003eSEGGER JTAG Isolator product page\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/Flasher_-_Hardware\"\u003eSEGGER Knowledge Base: Flasher Hardware (JTAG Isolator pinout)\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/debug-probes\/j-link\/accessories\/isolators\/j-link-swd-isolator\/\"\u003eSEGGER SWD Isolator product page\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/debug-probes\/j-link\/accessories\/isolators\/j-link-usb-isolator\/\"\u003eSEGGER USB Isolator product page\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/debug-probes\/j-trace\/accessories\/isolators\/j-trace-isolator\/\"\u003eSEGGER J-Trace Isolator product page\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/details\u003e","brand":"SEGGER Microcontroller GmbH","offers":[{"title":"Default Title","offer_id":44263173193951,"sku":"8.07.00","price":226.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0522\/6931\/8333\/files\/segger-microcontroller-gmbh-8-07-00-jtag-isolator-adapter-segger-8-07-00-debug-store-uk-42705861738719.png?v=1718110185"},{"product_id":"segger-8-12-28-j-link-pro-poe-debugger-uk","title":"SEGGER J-Link Pro PoE Debug Probe","description":"\u003cp\u003eThe SEGGER J-Link PRO PoE (part number 8.12.28) is an Ethernet and USB JTAG\/SWD debug probe powered over the network cable by IEEE 802.3af PoE (type 1, class 3), with up to 50 MHz target interface speed and download speeds up to 4 MB\/s. When PoE powered it can supply the target with 5.25V at up to 1000mA, and it includes licences for J-Flash, Unlimited Flash Breakpoints, Ozone and RDI. SEGGER built it for test farms: automated, regression and continuous integration testing where each probe sits on the LAN rather than beside a PC.\u003c\/p\u003e\n\n\u003ch2\u003ePower over Ethernet for Test Farm Nodes\u003c\/h2\u003e\n\u003cp\u003eOne Ethernet cable carries data and power, so each node in a rack needs no USB power supply. SEGGER's Test Farm reference design gives every node a J-Link PRO PoE, connected to the LAN through its Ethernet interface and can be powered from PoE switches where the LAN provides PoE. The device under test is connected to the probe by a USB cable so its power supply can be controlled, alongside a target adapter chosen to match its debug connector. On the probe itself, the USB-A port is listed as power only.\u003c\/p\u003e\n\n\u003ch2\u003eEthernet and USB Host Interfaces\u003c\/h2\u003e\n\u003cp\u003eThe probe connects by 100 Mbit\/s Ethernet or USB 2.0 Hi-Speed. In delivery condition it is configured for DHCP, and a static address can be set with J-Link Configurator. A built-in web server on TCP port 80 gives configuration access from a browser. The Ethernet data lines are isolated to IEEE 802.3 at a 1500 Vrms test voltage for one minute.\u003c\/p\u003e\n\n\u003ch2\u003e50 MHz JTAG\/SWD, Power Measurement and Licences\u003c\/h2\u003e\n\u003cp\u003eSEGGER lists the same speed and feature figures for the PRO PoE as for the J-Link PRO: up to 50 MHz target interface speed, SWO sampling up to 100 MHz, 1.2V to 5V target interface voltage and analogue power measurement at 200 kHz with 50µA resolution. The target uses the standard J-Link 20-pin 0.1\" connector; see our \u003ca href=\"\/it\/pages\/segger-j-link-20-pin-connector-pinout\"\u003eSEGGER J-Link 20-pin connector pinout\u003c\/a\u003e guide. The J-Link PRO feature list covers JTAG, cJTAG, SWD, SWD multi-drop, SWO, SPI, Microchip ICSP, Renesas FINE and Silicon Labs C2, with cores from ARM Cortex-M0 to Cortex-M85, Cortex-A and Cortex-R, RISC-V (SiFive, Andes, Codasip, Nuclei), Renesas RX, Microchip PIC32 and Silicon Labs EFM8. J-Flash is preinstalled, and RTT and VCOM are supported.\u003c\/p\u003e\n\n\u003ch2\u003eWhat Is in the Box\u003c\/h2\u003e\n\u003cp\u003eJ-Link PRO PoE probe, 20-pin 0.1\" ribbon cable and a USB cable. Mounting brackets are sold separately.\u003c\/p\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eHost interfaces\u003c\/th\u003e\n\u003ctd\u003e100 Mbit\/s Ethernet; USB 2.0 Hi-Speed\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePower over Ethernet\u003c\/th\u003e\n\u003ctd\u003eIEEE 802.3af PoE type 1, class 3\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget connector\u003c\/th\u003e\n\u003ctd\u003eJTAG\/SWD 20-pin, 0.1\" (2.54mm); USB-A (power only)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eSupported debug interfaces\u003c\/th\u003e\n\u003ctd\u003eJTAG, cJTAG, SWD, SWO, Microchip ICSP, Renesas FINE\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget interface voltage (VIF)\u003c\/th\u003e\n\u003ctd\u003e1.2V to 5V\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eCurrent drawn from VTref\u003c\/th\u003e\n\u003ctd\u003eLess than 25µA\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget supply, PoE powered\u003c\/th\u003e\n\u003ctd\u003e5.25V, max. 1000mA\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget supply, USB powered\u003c\/th\u003e\n\u003ctd\u003e5V, max. 400mA\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget interface speed\u003c\/th\u003e\n\u003ctd\u003eMax. 50 MHz\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eSWO sampling frequency\u003c\/th\u003e\n\u003ctd\u003eMax. 100 MHz\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDownload speed\u003c\/th\u003e\n\u003ctd\u003eUp to 4 MB\/s\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePower measurement\u003c\/th\u003e\n\u003ctd\u003e200 kHz sampling frequency, 50µA resolution\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eEthernet isolation\u003c\/th\u003e\n\u003ctd\u003eData lines to IEEE 802.3, 1500 Vrms for one minute\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eIncluded licences\u003c\/th\u003e\n\u003ctd\u003eJ-Flash (preinstalled), Unlimited Flash Breakpoints, Ozone, RDI\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDimensions (without cables)\u003c\/th\u003e\n\u003ctd\u003e123mm x 68mm x 30mm\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eWeight (without cables)\u003c\/th\u003e\n\u003ctd\u003e125g\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eOperating temperature\u003c\/th\u003e\n\u003ctd\u003e+5°C to +60°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eStorage temperature\u003c\/th\u003e\n\u003ctd\u003e-20°C to +65°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eRelative humidity\u003c\/th\u003e\n\u003ctd\u003eMax. 90% rH, non-condensing\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eEMC\u003c\/th\u003e\n\u003ctd\u003eEN 55032, EN 55035\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eHost OS\u003c\/th\u003e\n\u003ctd\u003eWindows and Linux (x86-64, ARM64); macOS (x86-64, Apple Silicon)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eLimitations\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003ePoE operation needs an IEEE 802.3af power source on the network side, such as a PoE switch; without one, power the probe from USB.\u003c\/li\u003e\n  \u003cli\u003eThe 1000mA target supply applies only when PoE powered; from USB the limit is 400mA.\u003c\/li\u003e\n  \u003cli\u003eThe Ethernet shield is not isolated; SEGGER specifies an unshielded twisted pair cable for effective isolation.\u003c\/li\u003e\n  \u003cli\u003eNo ETM trace on Cortex-M (use SEGGER J-Trace) and no QSPI target interface.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eJ-Link PRO PoE Compared with PLUS, ULTRA+ and PRO\u003c\/h2\u003e\n\u003cdiv style=\"overflow-x:auto\"\u003e\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eHost interface\u003c\/th\u003e\n\u003cth\u003eDownload speed\u003c\/th\u003e\n\u003cth\u003eTarget interface speed\u003c\/th\u003e\n\u003cth\u003eEthernet\u003c\/th\u003e\n\u003cth\u003ePower over Ethernet\u003c\/th\u003e\n\u003cth\u003eSupported cores\u003c\/th\u003e\n\u003cth\u003ePrice ex VAT\u003c\/th\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-8-02-28-j-link-plus-classic-debugger\"\u003eJ-Link PLUS Classic\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eUSB 2.0 Hi-Speed\u003c\/td\u003e\n\u003ctd\u003eUp to 1 MB\/s\u003c\/td\u003e\n\u003ctd\u003eUp to 15 MHz\u003c\/td\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003ctd\u003eARM Cortex-M\/A\/R, RISC-V, Renesas RX, PIC32, EFM8\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-8-02-28-j-link-plus-classic-debugger\"\u003e£660\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-j-link-ultra-plus-8-16-28\"\u003eJ-Link ULTRA+ (J-Link Ultra)\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eUSB 2.0 Hi-Speed\u003c\/td\u003e\n\u003ctd\u003eUp to 4 MB\/s\u003c\/td\u003e\n\u003ctd\u003eUp to 50 MHz\u003c\/td\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003ctd\u003eARM Cortex-M\/A\/R, RISC-V, Renesas RX, PIC32, EFM8\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-j-link-ultra-plus-8-16-28\"\u003e£870\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-j-link-pro-debugger-programmer-8-12-00\"\u003eJ-Link PRO\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eUSB 2.0 Hi-Speed and 100 Mbit\/s Ethernet\u003c\/td\u003e\n\u003ctd\u003eUp to 4 MB\/s\u003c\/td\u003e\n\u003ctd\u003eUp to 50 MHz\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003ctd\u003eARM Cortex-M\/A\/R, RISC-V, Renesas RX, PIC32, EFM8\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-j-link-pro-debugger-programmer-8-12-00\"\u003e£1,100\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eJ-Link PRO PoE (this product)\u003c\/td\u003e\n\u003ctd\u003eUSB 2.0 Hi-Speed and 100 Mbit\/s Ethernet\u003c\/td\u003e\n\u003ctd\u003eUp to 4 MB\/s\u003c\/td\u003e\n\u003ctd\u003eUp to 50 MHz\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003ctd\u003eYes, IEEE 802.3af\u003c\/td\u003e\n\u003ctd\u003eARM Cortex-M\/A\/R, RISC-V, Renesas RX, PIC32, EFM8\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-8-12-28-j-link-pro-poe-debugger-uk\"\u003e£1,320\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003c\/div\u003e\n\n\u003ch2\u003eTypical Applications\u003c\/h2\u003e\n\u003cp\u003eA rack of PRO PoE probes on a PoE switch, each flashing and testing one STM32 or nRF board per CI build, with the device under test power-cycled between runs. Regression testing of Cortex-M33 firmware on a remote bench reached over the LAN. Overnight soak tests where the probe reports RTT logs from a target that nobody is sitting next to.\u003c\/p\u003e\n\u003cp\u003eFor a single desk with USB, the ULTRA+ gives the same 50 MHz and 4 MB\/s figures; the J-Link PRO adds Ethernet without PoE.\u003c\/p\u003e\n\n\u003cp\u003eOrder the J-Link PRO PoE for \u003cspan data-ds-price=\"segger-8-12-28-j-link-pro-poe-debugger-uk\"\u003e£1,320\u003c\/span\u003e ex VAT. Ask us for a formal quotation for a test farm quantity, or check your part number against SEGGER's supported devices list. See the full range in our \u003ca href=\"\/it\/collections\/segger-debugger-catalogue-uk\"\u003eSEGGER debug probes\u003c\/a\u003e collection.\u003c\/p\u003e\n\n\u003cp\u003e\u003csmall\u003eLast reviewed: 30 October 2026\u003c\/small\u003e\u003c\/p\u003e\n\u003cdetails\u003e\u003csummary\u003e\u003csmall\u003eSources (7 manufacturer pages)\u003c\/small\u003e\u003c\/summary\u003e\u003cul\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/debug-probes\/j-link\/models\/j-link-pro-poe\/\"\u003eSEGGER J-Link Pro PoE product page\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/debug-probes\/j-link\/models\/j-link-pro\/\"\u003eSEGGER J-Link Pro product page\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/J-Link_PRO\"\u003eSEGGER Knowledge Base: J-Link PRO\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/Test_Farm\"\u003eSEGGER Knowledge Base: Test Farm\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/Setting_up_Ethernet_interface\"\u003eSEGGER Knowledge Base: Setting up Ethernet interface\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/debug-probes\/j-link\/models\/j-link-plus\/\"\u003eSEGGER J-Link PLUS product page\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/debug-probes\/j-link\/models\/j-link-ultra\/\"\u003eSEGGER J-Link Ultra product page\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/details\u003e","brand":"SEGGER Microcontroller GmbH","offers":[{"title":"Default Title","offer_id":44504770150623,"sku":"8.12.28","price":1320.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0522\/6931\/8333\/files\/segger-microcontroller-gmbh-8-12-28-j-link-pro-poe-debugger-segger-debug-store-uk-40759343874271.jpg?v=1699530961"},{"product_id":"j-link-upgrade-base-to-plus","title":"SEGGER J-Link Upgrade BASE to PLUS","description":"\u003cp\u003eThe SEGGER J-Link Upgrade BASE to PLUS (part number 8.08.13) is a software licence, not hardware: it adds the J-Link PLUS software bundle to a J-Link BASE Classic or J-Link BASE Compact you already own. The bundle covers J-Flash and J-Flash SPI, Unlimited Flash Breakpoints, the Ozone debugger, monitor-mode debugging and the J-Link ARM RDI\/RDDI licence pack. SEGGER issues it against the serial number of each probe, so it suits teams who bought BASE probes for debug and now need flash programming or flash breakpoints on the same units.\u003c\/p\u003e\n\n\u003ch2\u003eAdds the J-Link PLUS Licences to an Existing BASE\u003c\/h2\u003e\n\u003cp\u003eJ-Flash and J-Flash SPI program flash and EEPROM devices without an IDE. Unlimited Flash Breakpoints lets you set breakpoints in flash beyond the number of hardware breakpoints the core provides. Ozone is SEGGER's standalone debugger and performance analyser. Monitor mode keeps essential system functions running while the application is being debugged. The RDI\/RDDI licence pack covers debuggers that use that interface. Without the upgrade, SEGGER's BASE page states that J-Flash, Flash Breakpoints and Ozone do not work with a J-Link BASE.\u003c\/p\u003e\n\n\u003ch2\u003eHow the Upgrade Is Applied\u003c\/h2\u003e\n\u003cp\u003eThe upgrade is a digital product. SEGGER needs the serial number of each J-Link BASE to be upgraded, and several serial numbers can be supplied for a multi-probe order, so have them ready when you order. SEGGER's Knowledge Base describes two ways J-Link licences are installed: on the host PC with the J-Link License Manager, or as a portable licence held on the probe, managed with the License command in J-Link Commander. The probe hardware, cables and target connections stay as they are. SEGGER includes 6 months of free support and updates with the upgrade.\u003c\/p\u003e\n\n\u003ch2\u003eWhat the Upgrade Does Not Change\u003c\/h2\u003e\n\u003cp\u003eThe licences do not change the hardware. An upgraded BASE keeps its 1.2V to 5V target interface, up to 15 MHz target interface speed and download speeds up to 1 MB\/s, which are the same figures SEGGER lists for J-Link PLUS. Faster interface clocks and Ethernet need different hardware, such as the J-Link ULTRA+ or PRO.\u003c\/p\u003e\n\n\u003ch2\u003eWhat's Included\u003c\/h2\u003e\n\u003cp\u003eA licence for J-Flash and J-Flash SPI, Unlimited Flash Breakpoints, Ozone, monitor mode and J-Link ARM RDI\/RDDI, issued for the J-Link BASE serial number you supply. No hardware or cables are supplied.\u003c\/p\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003e8.08.13\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eProduct type\u003c\/th\u003e\n\u003ctd\u003eSoftware licence upgrade, digital product\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eFor use with\u003c\/th\u003e\n\u003ctd\u003eJ-Link BASE Classic, J-Link BASE Compact\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eLicences added\u003c\/th\u003e\n\u003ctd\u003eJ-Flash \/ J-Flash SPI, Unlimited Flash Breakpoints, Ozone, Monitor Mode, J-Link ARM RDI\/RDDI\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eRequired to order\u003c\/th\u003e\n\u003ctd\u003eSerial number of each J-Link BASE to be upgraded\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eLicence management tools\u003c\/th\u003e\n\u003ctd\u003eJ-Link License Manager (host PC); J-Link Commander License command (portable licence on the probe)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eSupport from SEGGER\u003c\/th\u003e\n\u003ctd\u003e6 months of free support and updates\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eLimitations\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eFor J-Link BASE probes only; it is issued against the serial number of each probe.\u003c\/li\u003e\n  \u003cli\u003eLicences only: target interface speed stays at up to 15 MHz and download speed at up to 1 MB\/s.\u003c\/li\u003e\n  \u003cli\u003eNo ETM trace (use SEGGER J-Trace) and no QSPI target interface, as on the BASE.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eUpgrade Compared with Buying a J-Link PLUS\u003c\/h2\u003e\n\u003cdiv style=\"overflow-x:auto\"\u003e\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eOption\u003c\/th\u003e\n\u003cth\u003eWhat you get\u003c\/th\u003e\n\u003cth\u003eForm factor\u003c\/th\u003e\n\u003cth\u003ePrice ex VAT\u003c\/th\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eJ-Link Upgrade BASE to PLUS (this product)\u003c\/td\u003e\n\u003ctd\u003ePLUS licences for a BASE you already own\u003c\/td\u003e\n\u003ctd\u003eLicence only\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"j-link-upgrade-base-to-plus\"\u003e£320\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\n\u003ca href=\"\/it\/products\/segger-8-08-00-j-link-base-classic\"\u003eJ-Link BASE Classic\u003c\/a\u003e plus upgrade\u003c\/td\u003e\n\u003ctd\u003eNew probe with PLUS licences added\u003c\/td\u003e\n\u003ctd\u003e100 x 53 x 27mm, USB Type B\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-8-08-00-j-link-base-classic+j-link-upgrade-base-to-plus\"\u003e£790\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-8-02-28-j-link-plus-classic-debugger\"\u003eJ-Link PLUS Classic\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eNew probe, licences included, J-Flash preinstalled\u003c\/td\u003e\n\u003ctd\u003e100 x 53 x 27mm, USB Type B\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-8-02-28-j-link-plus-classic-debugger\"\u003e£660\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-j-link-plus-compact-8-19-28\"\u003eJ-Link PLUS Compact\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eNew probe, licences included, J-Flash preinstalled\u003c\/td\u003e\n\u003ctd\u003e46 x 46 x 17mm, USB-C, two mounting holes\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-j-link-plus-compact-8-19-28\"\u003e£660\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003c\/div\u003e\n\n\u003ch2\u003eTypical Applications\u003c\/h2\u003e\n\u003cp\u003eTurning bench BASE probes into J-Flash programming stations for a pilot build of STM32 or NXP boards. Adding Unlimited Flash Breakpoints when a Cortex-M application running from flash needs more breakpoints than the core provides. Giving a team that already owns BASE probes access to Ozone without replacing hardware.\u003c\/p\u003e\n\n\u003cp\u003eOrder the J-Link Upgrade BASE to PLUS for \u003cspan data-ds-price=\"j-link-upgrade-base-to-plus\"\u003e£320\u003c\/span\u003e ex VAT, with the serial number of each probe to be upgraded. Ask us for a formal quotation for several probes. See the full range in our \u003ca href=\"\/it\/collections\/segger-debugger-catalogue-uk\"\u003eSEGGER debug probes\u003c\/a\u003e collection.\u003c\/p\u003e\n\n\u003cp\u003e\u003csmall\u003eLast reviewed 16\/11\/2026.\u003c\/small\u003e\u003c\/p\u003e\n\u003cdetails\u003e\u003csummary\u003e\u003csmall\u003eSources (6 manufacturer pages)\u003c\/small\u003e\u003c\/summary\u003e\u003cul\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/shop.segger.com\/debug-trace-probes\/software-add-ons\/j-link-upgrade-base-to-plus\"\u003eSEGGER shop: J-Link Upgrade BASE to PLUS\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/shop-us.segger.com\/Upgrade_p\/8.08.13.htm\"\u003eSEGGER US shop: J-Link Upgrade Base to Plus (8.08.13)\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/purchase\/pricing\/jlink-related\/\"\u003eSEGGER J-Link pricing and licence overview\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/debug-probes\/j-link\/models\/j-link-base\/\"\u003eSEGGER J-Link BASE product page\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/J-Link_License_Installation\"\u003eSEGGER Knowledge Base: J-Link License Installation\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/J-Link_License_Manager\"\u003eSEGGER Knowledge Base: J-Link License Manager\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/details\u003e","brand":"SEGGER Microcontroller GmbH","offers":[{"title":"Default Title","offer_id":55260963766647,"sku":"8.08.13","price":320.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0522\/6931\/8333\/files\/segger-microcontroller-gmbh-8-08-13-j-link-upgrade-base-to-plus-1170616515.png?v=1748523066"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0522\/6931\/8333\/collections\/lg-segger-J-link-base-angle-left.jpg?v=1724338185","url":"https:\/\/thedebugstore.com\/it\/collections\/segger-debugger-catalogue-uk.oembed","provider":"Debug Store","version":"1.0","type":"link"}