{"title":"Cluster Programmers","description":"\u003cp\u003eCluster programming means running multiple programmers in parallel, typically one per sub-board on a PCB panel or one per site on a multi-site test rig. The secondary terms multi-site programming and parallel ISP (in-system programming) describe the same approach. Xeltek uses the term cluster programming in its own literature. This collection covers cluster setups from Xeltek, Dediprog and SEGGER (Flasher Hub clusters).\u003c\/p\u003e","products":[{"product_id":"dediprog-sf100-spi-programmer-uk","title":"Programmatore di flash SPI NOR Dediprog SF100","description":"\u003ch3\u003eHardware\u003c\/h3\u003e\n\n\u003cp\u003eIl\u003cstrong\u003e Dediprog SF100\u003c\/strong\u003e è dotato di un connettore ISP: tramite un connettore adeguato, l'utente può collegare il programmatore e pilotare i segnali SPI, alimentare la memoria e controllare lo stato del controller o dell'applicazione. Per la piedinatura del connettore 2x7 dell'SF100 fare riferimento alla tabella 1. DediProg fornisce anche il cavo ISP SF100, che serve a collegare il programmatore SF100 al connettore ISP 2X4 da 2.54mm presente sulla scheda; per la piedinatura 2x4 del cavo ISP SF100 fare riferimento alla tabella 2.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003ePiedinatura del connettore ISP dell'SF100 (2x7)\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003ctable align=\"center\" border=\"1\"\u003e\n\t\u003ctbody\u003e\n\t\t\u003ctr\u003e\n\t\t\t\u003ctd\u003e1\u003c\/td\u003e\n\t\t\t\u003ctd\u003eI\/O1\u003c\/td\u003e\n\t\t\t\u003ctd\u003eI\/O4\u003c\/td\u003e\n\t\t\t\u003ctd\u003e2\u003c\/td\u003e\n\t\t\u003c\/tr\u003e\n\t\t\u003ctr\u003e\n\t\t\t\u003ctd\u003e3\u003c\/td\u003e\n\t\t\t\u003ctd\u003eI\/O2 o CS2\u003c\/td\u003e\n\t\t\t\u003ctd\u003eNC\u003c\/td\u003e\n\t\t\t\u003ctd\u003e4\u003c\/td\u003e\n\t\t\u003c\/tr\u003e\n\t\t\u003ctr\u003e\n\t\t\t\u003ctd\u003e5\u003c\/td\u003e\n\t\t\t\u003ctd\u003eVcc\u003c\/td\u003e\n\t\t\t\u003ctd\u003eGND\u003c\/td\u003e\n\t\t\t\u003ctd\u003e6\u003c\/td\u003e\n\t\t\u003c\/tr\u003e\n\t\t\u003ctr\u003e\n\t\t\t\u003ctd\u003e7\u003c\/td\u003e\n\t\t\t\u003ctd\u003eCS\u003c\/td\u003e\n\t\t\t\u003ctd\u003eCLK\u003c\/td\u003e\n\t\t\t\u003ctd\u003e8\u003c\/td\u003e\n\t\t\u003c\/tr\u003e\n\t\t\u003ctr\u003e\n\t\t\t\u003ctd\u003e9\u003c\/td\u003e\n\t\t\t\u003ctd\u003eMISO\u003c\/td\u003e\n\t\t\t\u003ctd\u003eMOSI\u003c\/td\u003e\n\t\t\t\u003ctd\u003e10\u003c\/td\u003e\n\t\t\u003c\/tr\u003e\n\t\t\u003ctr\u003e\n\t\t\t\u003ctd\u003e11\u003c\/td\u003e\n\t\t\t\u003ctd\u003eVpp\/Acc\u003c\/td\u003e\n\t\t\t\u003ctd\u003eI\/O3\u003c\/td\u003e\n\t\t\t\u003ctd\u003e12\u003c\/td\u003e\n\t\t\u003c\/tr\u003e\n\t\t\u003ctr\u003e\n\t\t\t\u003ctd\u003e13\u003c\/td\u003e\n\t\t\t\u003ctd\u003eSCL\u003c\/td\u003e\n\t\t\t\u003ctd\u003eSDA\u003c\/td\u003e\n\t\t\t\u003ctd\u003e14\u003c\/td\u003e\n\t\t\u003c\/tr\u003e\n\t\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003cp\u003e \u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003ePiedinatura del connettore del cavo ISP (2x4)\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003ctable align=\"center\" border=\"1\"\u003e\n\t\u003ctbody\u003e\n\t\t\u003ctr\u003e\n\t\t\t\u003ctd\u003e1\u003c\/td\u003e\n\t\t\t\u003ctd\u003eVcc\u003c\/td\u003e\n\t\t\t\u003ctd\u003eGND\u003c\/td\u003e\n\t\t\t\u003ctd\u003e2\u003c\/td\u003e\n\t\t\u003c\/tr\u003e\n\t\t\u003ctr\u003e\n\t\t\t\u003ctd\u003e3\u003c\/td\u003e\n\t\t\t\u003ctd\u003eCS\u003c\/td\u003e\n\t\t\t\u003ctd\u003eCLK\u003c\/td\u003e\n\t\t\t\u003ctd\u003e4\u003c\/td\u003e\n\t\t\u003c\/tr\u003e\n\t\t\u003ctr\u003e\n\t\t\t\u003ctd\u003e5\u003c\/td\u003e\n\t\t\t\u003ctd\u003eMISO\u003c\/td\u003e\n\t\t\t\u003ctd\u003eMOSI\u003c\/td\u003e\n\t\t\t\u003ctd\u003e6\u003c\/td\u003e\n\t\t\u003c\/tr\u003e\n\t\t\u003ctr\u003e\n\t\t\t\u003ctd\u003e7\u003c\/td\u003e\n\t\t\t\u003ctd\u003eVpp\/Acc\u003c\/td\u003e\n\t\t\t\u003ctd\u003eI\/O3\u003c\/td\u003e\n\t\t\t\u003ctd\u003e8\u003c\/td\u003e\n\t\t\u003c\/tr\u003e\n\t\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003cp\u003e \u003c\/p\u003e\n\n\u003ch3\u003eSoftware applicativo SF100\u003c\/h3\u003e\n\n\u003cp\u003eLa catena di strumenti software USB dell'SF100 offre grande flessibilità e si adatta a esigenze diverse e ai requisiti più elevati:\u003c\/p\u003e\n\n\u003ch4\u003e\u003cstrong\u003eModalità Ingegneria\u003c\/strong\u003e\u003c\/h4\u003e\n\n\u003cp\u003ePer ingegneri ed esperti che devono accedere a funzioni avanzate per sviluppo, riparazione ecc.\u003c\/p\u003e\n\n\u003ch4\u003e\u003cstrong\u003eModalità Produzione\u003c\/strong\u003e\u003c\/h4\u003e\n\n\u003cp\u003eIl software applicativo SF100 supporta la \u003cstrong\u003eprogrammazione multipla (Gang Programming)\u003c\/strong\u003e\u003cstrong\u003e. \u003c\/strong\u003eÈ possibile aggiungere altri programmatori in qualsiasi momento, quando occorre aumentare la capacità produttiva.\u003c\/p\u003e\n\n\u003cp\u003ePer gli operatori di produzione, per controllare più programmatori e migliorare la produttività.\u003c\/p\u003e\n\n\u003ch4\u003e\u003cstrong\u003eRiga di comando\u003c\/strong\u003e\u003c\/h4\u003e\n\n\u003cp\u003eIl software del cliente può controllare più programmatori SF100 tramite interfaccia a riga di comando.\u003c\/p\u003e\n\n\u003ch4\u003e \u003c\/h4\u003e","brand":"Dediprog Technology Co Ltd","offers":[{"title":"Default Title","offer_id":37768306950333,"sku":"SF100","price":290.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0522\/6931\/8333\/files\/dediprog-technology-co-ltd-sf100-dediprog-sf100-spi-nor-flash-programmer-70707502580087.png?v=1727574581"},{"product_id":"superpro-6000-universal-programmer-xeltek-uk","title":"Xeltek SuperPro 6000 Fast Universal Programmer","description":"\u003cp\u003eThe Xeltek SuperPro 6000 is a 144-pin universal programmer with a 32-bit ARM9 MCU running Linux for algorithm processing, a USB 2.0 host link and a stand-alone mode that runs projects from a CompactFlash card. Xeltek's published SuperPro 6000 device list covers 89,932 devices from 322 IC manufacturers, spanning EPROM, EEPROM, flash, PLD, bipolar PROM, SRAM and microcontrollers. It suits engineering benches that program parts off-board and production lines that cluster several programmers for volume work.\u003c\/p\u003e\n\n\u003ch2\u003e144 Universal Pin Drivers and CX Socket Adapters\u003c\/h2\u003e\n\u003cp\u003eAll 144 pin drivers are built into the main unit, so no separate pin expander is needed for high pin-count packages. The programmer ships with the removable CX0001 adapter, a 48-pin DIP ZIF socket. Other packages, including PLCC, SOIC, SOP, TSOP, TSSOP, QFP and BGA, use optional CX-series socket adapters, which Xeltek lists for the SuperPro 5000\/5000E, 6000\/6000E and 5004GP. For 48-pin and smaller devices an insertion test checks for poor pin contact before the operation starts.\u003c\/p\u003e\n\n\u003ch2\u003eStand-Alone Universal Programmer for Production Lines\u003c\/h2\u003e\n\u003cp\u003eIn PC-hosted mode the SuperPro 6000 is driven over USB 2.0 from the SuperPro software. For production, a project is saved to a CompactFlash card and the unit runs without a PC, operated from its own LCD and keypad. Several units can work concurrently; Xeltek's brochure lists clusters of up to 15 units for volume production.\u003c\/p\u003e\n\u003cp\u003eProduction mode detects chip insertion and removal and starts the batch automatically. Project files can be password protected, so line operators load a locked configuration rather than setting device options by hand.\u003c\/p\u003e\n\n\u003ch2\u003eSuperPro Software, Batch Sequences and Serial Numbers\u003c\/h2\u003e\n\u003cp\u003eThe Edit Auto function chains operations such as Erase, Blank Check, Program and Verify into one sequence. Auto-increment serial numbering runs in Binary, ASCII Decimal or ASCII Hex, and a log file records each session (off, new file or append). Serial numbering works in PC-hosted mode only, not in stand-alone mode. Vcc verification runs once at the device's nominal Vcc, or twice at plus or minus 5% or plus or minus 10% of it (for a 5V part, 4.75V\/5.25V or 4.50V\/5.50V).\u003c\/p\u003e\n\u003cp\u003eThe current SuperPro 6000 software package (nsp6kw, dated February 2018) runs on Windows XP, Vista, 7, 8 and 10, 32-bit and 64-bit. The host PC needs USB 2.0 and 1 GB of free disk space.\u003c\/p\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003ePin drivers\u003c\/th\u003e\n\u003ctd\u003e144 universal, built in\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eProcessor\u003c\/th\u003e\n\u003ctd\u003e32-bit ARM9 MCU with Linux for algorithm processing\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDevice list (Xeltek, 2014)\u003c\/th\u003e\n\u003ctd\u003e89,932 devices from 322 manufacturers\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDevice types\u003c\/th\u003e\n\u003ctd\u003eEPROM, EEPROM, flash, PLD, bipolar PROM, DRAM\/SRAM, MCU\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDevice Vcc\u003c\/th\u003e\n\u003ctd\u003e1.2V to 5V\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eStandard socket\u003c\/th\u003e\n\u003ctd\u003eRemovable CX0001 adapter, 48-pin DIP ZIF\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eOptional adapters\u003c\/th\u003e\n\u003ctd\u003eCX series: PLCC, TSOP, SOIC, SOP, QFP, TSSOP, BGA and others\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePC interface\u003c\/th\u003e\n\u003ctd\u003eUSB 2.0\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eStand-alone storage\u003c\/th\u003e\n\u003ctd\u003eCompactFlash card\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eStand-alone controls\u003c\/th\u003e\n\u003ctd\u003eLCD and keypad\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eVcc verification\u003c\/th\u003e\n\u003ctd\u003eNominal Vcc, or plus or minus 5% or plus or minus 10%\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eIn-system programming\u003c\/th\u003e\n\u003ctd\u003eVia optional ISP\/ICP adapter\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eHost OS\u003c\/th\u003e\n\u003ctd\u003eWindows XP, Vista, 7, 8, 10 (32\/64-bit)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eCompliance\u003c\/th\u003e\n\u003ctd\u003eCE, RoHS\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eLimitations\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eXeltek now lists the SuperPro 6000 in its Legacy Programmer Download Center, and its published device list dates from 2014. Check your part number against the device list PDF in Downloads before ordering.\u003c\/li\u003e\n  \u003cli\u003ePackages other than 48-pin DIP need a CX-series socket adapter, ordered separately. Xeltek lists the SA series for its 48-pin-driver SuperPro programmers (the 610P and 611S, and older models including the SuperPro M), not the 6000. The \u003ca href=\"\/it\/products\/superpro-m-low-cost-universal-programmer-xeltek-uk\"\u003eSuperPro M\u003c\/a\u003e is the only SA-compatible programmer we sell.\u003c\/li\u003e\n  \u003cli\u003eIn-circuit programming needs the optional ISP\/ICP adapter. For dedicated in-system production programming over I2C, JTAG or SPI, see the \u003ca href=\"\/it\/products\/xeltek-superpro-is01-in-system-programmer-uk\"\u003eSuperPro IS01\u003c\/a\u003e (\u003cspan data-ds-price=\"xeltek-superpro-is01-in-system-programmer-uk\"\u003e£1,145.84\u003c\/span\u003e).\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eSuperPro 6000 vs SuperPro 6000E\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003e\u003c\/th\u003e\n\u003cth\u003eSuperPro 6000\u003c\/th\u003e\n\u003cth\u003e\u003ca href=\"\/it\/products\/superpro-6000e-universal-programmer-xeltek-uk\"\u003eSuperPro 6000E\u003c\/a\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePrice (ex VAT)\u003c\/th\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"superpro-6000-universal-programmer-xeltek-uk\"\u003e£935\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"superpro-6000e-universal-programmer-xeltek-uk\"\u003e£880\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eProcessor\u003c\/th\u003e\n\u003ctd\u003e32-bit ARM9 MCU with Linux\u003c\/td\u003e\n\u003ctd\u003e32-bit RISC MCU\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePin drivers\u003c\/th\u003e\n\u003ctd\u003e144\u003c\/td\u003e\n\u003ctd\u003e144\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eXeltek device list\u003c\/th\u003e\n\u003ctd\u003e89,932 devices from 322 manufacturers (Xeltek device list, 2014)\u003c\/td\u003e\n\u003ctd\u003e83,300+ devices from 299 manufacturers (Xeltek comparison sheet, October 2013)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDevice Vcc\u003c\/th\u003e\n\u003ctd\u003e1.2V to 5V (Xeltek brochure)\u003c\/td\u003e\n\u003ctd\u003eDown to 1.2V\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eStand-alone\u003c\/th\u003e\n\u003ctd\u003eCompactFlash, LCD and keypad\u003c\/td\u003e\n\u003ctd\u003eCompactFlash, 20 x 4 LCD, 6-key keypad\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eSocket adapters\u003c\/th\u003e\n\u003ctd\u003eCX series\u003c\/td\u003e\n\u003ctd\u003eCX series\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePC interface\u003c\/th\u003e\n\u003ctd\u003eUSB 2.0\u003c\/td\u003e\n\u003ctd\u003eUSB 2.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eTypical Applications\u003c\/h2\u003e\n\u003cp\u003eOff-board programming of legacy parallel EPROM and EEPROM in PLCC and DIP packages for product maintenance. Production programming of microcontrollers and NOR flash in QFP and TSOP through CX adapters, with clustered units running password-protected projects from CompactFlash. Batch Erase, Blank Check, Program and Verify with serialisation and logging for traceable runs.\u003c\/p\u003e\n\u003cp\u003eThe SuperPro 6000 suits production engineers running programming stations and test benches that need one 144-pin programmer for a broad device mix.\u003c\/p\u003e\n\n\u003ch2\u003eWhat's Included\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eSuperPro 6000 programming module with removable CX0001 DIP48 adapter\u003c\/li\u003e\n  \u003cli\u003ePower supply unit\u003c\/li\u003e\n  \u003cli\u003eUSB cable\u003c\/li\u003e\n  \u003cli\u003eSoftware CD\u003c\/li\u003e\n  \u003cli\u003eUser's Guide and registration form\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eOrder the SuperPro 6000 from \u003cspan data-ds-price=\"superpro-6000-universal-programmer-xeltek-uk\"\u003e£935\u003c\/span\u003e ex VAT. Send us your device part numbers and packages and we will confirm support and the CX adapter you need, or request a formal quotation. See the full \u003ca href=\"\/it\/collections\/xeltek-programmers-catalogue\"\u003eXeltek range\u003c\/a\u003e of programmers and adapters.\u003c\/p\u003e\n\n\u003cp\u003e\u003csmall\u003eLast reviewed: 30 October 2026\u003c\/small\u003e\u003c\/p\u003e\n\u003cdetails\u003e\u003csummary\u003e\u003csmall\u003eSources (3 manufacturer pages)\u003c\/small\u003e\u003c\/summary\u003e\u003cul\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.xeltek.com\/software\/sp6000\/sp6000Device.php\"\u003eXeltek: Supported devices for SuperPro 6000\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.xeltek.com\/superpro-software-download-center-en-en\/legacy-programer-download-centerm\/\"\u003eXeltek: Legacy Programmer Download Center\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/pages.xeltek.com\/xeltekadaptercompatibility\/\"\u003eXeltek: SuperPro and SuperBot socket adapter compatibility\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/details\u003e","brand":"Xeltek, Inc","offers":[{"title":"Default Title","offer_id":37768320549053,"sku":"SuperPro-6000","price":935.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0522\/6931\/8333\/products\/xeltek-inc-programmer-xeltek-superpro-6000-fast-universal-programmer-23152153198781.jpg?v=1685148044"},{"product_id":"xeltek-superpro-is01-in-system-programmer-uk","title":"Xeltek SuperPro IS01 High-Performance In-System Programmer","description":"\u003cp\u003eThe Xeltek SuperPro IS01 programs parts already soldered to the board, from firmware bring-up to end-of-line serial number writing. It supports over 10,000 serial programmable devices over I2C, SPI, UART, BDM, Microwire, JTAG, CAN and RS-232, supplies target VDD up to 5.5V at 0.5A and VPP up to 15V at 0.2A, runs from a PC over USB 2.0 or on its own from project files on an SD card, and has an optocoupler-isolated ATE port for fixtures.\u003c\/p\u003e\n\n\u003ch2\u003eIn-System Programming Over a Cable of Up to 1 m\u003c\/h2\u003e\n\u003cp\u003eAs a serial in-system programmer, the IS01 reaches targets up to 3 feet (1 m) away, with programming speed selectable in software to suit cable length and board loading. I\/O level is set in software from 1.5V to 4V. It can power a light-load target, though Xeltek recommends the board's own supply in most cases.\u003c\/p\u003e\n\u003cp\u003ePort A (10x2) carries every protocol except CAN and RS-232, including SPI, I2C, JTAG, UART, BDM and Microwire; Port B (5x2) carries CAN and RS-232.\u003c\/p\u003e\n\n\u003ch2\u003eStand-Alone Production Programming with ATE Control\u003c\/h2\u003e\n\u003cp\u003eStand-alone, the IS01 runs from its LCD, keypad and LED status indicator, loading password-protectable project files from an SD card (maximum 4GB). Each project holds the device, buffer data, configuration bits and batch sequence.\u003c\/p\u003e\n\u003cp\u003eThe optocoupler-isolated ATE interface gives fixtures six project select lines (SEL0 to SEL5), START and STOP inputs and PASS, FAIL and BUSY outputs. In mass production mode, shorting TPIN and TPOUT on the target board starts the AUTO sequence (erase, blank check, program, verify, protect) as soon as the board connects. Up to 12 programmers run from one PC through a USB hub.\u003c\/p\u003e\n\n\u003ch2\u003eSoftware, CPLD Files and Test System Integration\u003c\/h2\u003e\n\u003cp\u003eThe Windows software adds production logs, password-locked Factory Mode, auto-increment serial numbers and automatic recognition of binary, Intel hex, Motorola S, Tektronix, JEDEC and POF files. XPlayer runs JAM, SVF and STAPL (.stp) files for Actel, Xilinx and Altera programmable logic, generated in design tools such as Quartus II or ISE, plus Actel Direct C files. An optional DLL or Virtual COM command set, and a LabVIEW driver, let ICT equipment test and program in one step.\u003c\/p\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eSupported devices\u003c\/th\u003e\n\u003ctd\u003e10,000+ serial programmable devices\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eISP protocols\u003c\/th\u003e\n\u003ctd\u003eI2C, SPI, UART, BDM, Microwire (MW), JTAG, CAN, RS-232\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eISP ports\u003c\/th\u003e\n\u003ctd\u003ePort A 10x2 (all protocols except CAN and RS-232); Port B 5x2 (CAN, RS-232)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget VDD output\u003c\/th\u003e\n\u003ctd\u003e0V to 5.5V, 0.5A\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eVPP output\u003c\/th\u003e\n\u003ctd\u003e0V to 15V, 0.2A\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eI\/O level\u003c\/th\u003e\n\u003ctd\u003e1.5V to 4V, set in software\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eISP cable reach\u003c\/th\u003e\n\u003ctd\u003eUp to 3 ft (1 m), programming speed selectable\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePC interface\u003c\/th\u003e\n\u003ctd\u003eUSB 2.0 high speed; online and offline modes simultaneously\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eStand-alone operation\u003c\/th\u003e\n\u003ctd\u003eLCD, keypad, LED status; project files on SD card (max 4GB)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eATE interface\u003c\/th\u003e\n\u003ctd\u003eSEL0 to SEL5, START, STOP inputs; PASS, FAIL, BUSY outputs; optocoupler isolated\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eMulti-programming\u003c\/th\u003e\n\u003ctd\u003eUp to 12 programmers from one PC\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eIntegration\u003c\/th\u003e\n\u003ctd\u003eOptional DLL or Virtual COM command set; LabVIEW driver\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePower input\u003c\/th\u003e\n\u003ctd\u003e12V DC, 2A external\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eProtection\u003c\/th\u003e\n\u003ctd\u003eBuilt-in overcurrent protection\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eOperating temperature\u003c\/th\u003e\n\u003ctd\u003e10°C to 50°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDimensions (main unit)\u003c\/th\u003e\n\u003ctd\u003e137 x 87 x 45 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eWeight (main unit)\u003c\/th\u003e\n\u003ctd\u003e0.34 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eSoftware OS\u003c\/th\u003e\n\u003ctd\u003eWindows XP, Vista, 7, 8, 10 (32\/64-bit); Xeltek's current software listing also names Windows 11\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eLimitations\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eIn-system programming only. There is no ZIP socket, so loose chips need a socket-based universal programmer such as the \u003ca href=\"\/it\/products\/superpro-6000e-universal-programmer-xeltek-uk\"\u003eSuperPro 6000E\u003c\/a\u003e or \u003ca href=\"\/it\/products\/superpro-6000-universal-programmer-xeltek-uk\"\u003eSuperPro 6000\u003c\/a\u003e.\u003c\/li\u003e\n  \u003cli\u003eCAN and RS-232 targets on Port B need the optional ISP cable type B.\u003c\/li\u003e\n  \u003cli\u003eTarget VDD is rated at 0.5A; power heavier boards from their own supply. Long or heavily loaded lines may need a lower programming speed.\u003c\/li\u003e\n  \u003cli\u003eProtocol support does not guarantee a part is in the library; check the IS01 device list.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eCompare Xeltek SuperPro Programmers\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003cth\u003eTarget connection\u003c\/th\u003e\n\u003cth\u003eDevices\u003c\/th\u003e\n\u003cth\u003ePrice\u003c\/th\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eSuperPro IS01\u003c\/td\u003e\n\u003ctd\u003eIn-system programmer, stand-alone or USB 2.0\u003c\/td\u003e\n\u003ctd\u003eISP cable, up to 1 m\u003c\/td\u003e\n\u003ctd\u003e10,000+ serial devices\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"xeltek-superpro-is01-in-system-programmer-uk\"\u003e£1,145.84\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/superpro-6000e-universal-programmer-xeltek-uk\"\u003eSuperPro 6000E\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eUniversal programmer, stand-alone or USB 2.0\u003c\/td\u003e\n\u003ctd\u003e144-pin driver, socket adapters\u003c\/td\u003e\n\u003ctd\u003e83,300+ devices from 299 manufacturers (Xeltek comparison sheet, October 2013)\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"superpro-6000e-universal-programmer-xeltek-uk\"\u003e£880\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/superpro-6000-universal-programmer-xeltek-uk\"\u003eSuperPro 6000\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eUniversal programmer, stand-alone or USB 2.0\u003c\/td\u003e\n\u003ctd\u003e144-pin driver, socket adapters\u003c\/td\u003e\n\u003ctd\u003e89,932 devices from 322 manufacturers (Xeltek device list, 2014)\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"superpro-6000-universal-programmer-xeltek-uk\"\u003e£935\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/superpro-m-low-cost-universal-programmer-xeltek-uk\"\u003eSuperPro M\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eUniversal programmer, PC hosted over USB 2.0\u003c\/td\u003e\n\u003ctd\u003e48 pin drivers, socket adapters\u003c\/td\u003e\n\u003ctd\u003e20,000+ devices from 158 manufacturers\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"superpro-m-low-cost-universal-programmer-xeltek-uk\"\u003e£137.50\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eTypical Applications\u003c\/h2\u003e\n\u003cp\u003eWriting a unique serial number or calibration data to an on-board I2C EEPROM after final assembly, using auto-increment. Programming soldered SPI flash and microcontrollers on a bed-of-nails fixture, with the ATE lines selecting the project from the SD card and reporting PASS or FAIL to the handler. Updating Altera MAX II CPLDs such as the EPM240 or EPM570 in circuit from a JAM file through XPlayer.\u003c\/p\u003e\n\u003cp\u003eThe IS01 suits test engineers adding programming to an ICT or functional test station, and field service teams needing a portable programmer that runs without a PC. See the full \u003ca href=\"\/it\/collections\/xeltek-programmers-catalogue\"\u003eXeltek range\u003c\/a\u003e of programmers and adapters.\u003c\/p\u003e\n\n\u003ch2\u003eWhat's Included\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eSuperPro IS01 programmer\u003c\/li\u003e\n  \u003cli\u003eISP cable type A (all protocols except CAN and RS-232)\u003c\/li\u003e\n  \u003cli\u003eUSB cable\u003c\/li\u003e\n  \u003cli\u003ePower adapter, 12V DC output\u003c\/li\u003e\n  \u003cli\u003eInstallation CD-ROM\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eDocuments: \u003ca href=\"https:\/\/files.thedebugstore.com\/xeltek\/superpro-is01\/xeltek-superpro-is01-in-system-programmer-user-manual.pdf\"\u003eSuperPro IS01 user manual\u003c\/a\u003e and \u003ca href=\"https:\/\/files.thedebugstore.com\/xeltek\/superpro-is01\/xeltek-superpro-is01-supported-device-list-other.pdf\"\u003eSuperPro IS01 supported device list\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003cp\u003eOrder the SuperPro IS01 from \u003cspan data-ds-price=\"xeltek-superpro-is01-in-system-programmer-uk\"\u003e£1,145.84\u003c\/span\u003e ex VAT. Send us your target part numbers for a device list check or a formal quotation. Debug Store has supplied engineers for 55+ years.\u003c\/p\u003e\n\n\u003cp\u003e\u003csmall\u003eLast reviewed: 30 October 2026\u003c\/small\u003e\u003c\/p\u003e\n\u003cdetails\u003e\u003csummary\u003e\u003csmall\u003eSources (4 manufacturer pages)\u003c\/small\u003e\u003c\/summary\u003e\u003cul\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.xeltek.com\/isp-programmers\/in-system-programmers-superpro-is01\/\"\u003eXeltek SuperPro IS01 In-System (ISP) Programmer\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.xeltek.com\/resources\/technical-articles\/in-system-programming\/superpro-is01-mass-production-mode\/\"\u003eXeltek: SuperPro IS01 Mass Production Mode\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.xeltek.com\/resources\/technical-articles\/in-system-programming\/using-the-ate-port-to-control-isp-programmers\/\"\u003eXeltek: Using the ATE Port to Control ISP Programmers\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.xeltek.com\/resources\/technical-articles\/in-system-programming\/xeltek-superpro-is01-isp-in-circuit-programmer-uses-xplayer-tool-to-program-cpld-chips-by-altera-and-actel\/\"\u003eXeltek: SuperPro IS01 XPlayer for Altera and Actel CPLDs\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/details\u003e","brand":"Xeltek, Inc","offers":[{"title":"Default Title","offer_id":37768320614589,"sku":"SuperPro-IS01","price":1145.84,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0522\/6931\/8333\/products\/xeltek-inc-programmer-xeltek-superpro-is01-high-performance-in-system-programmer-30219321540797.jpg?v=1685218792"},{"product_id":"superpro-6000e-universal-programmer-xeltek-uk","title":"Xeltek SuperPro 6000E Ultra-Fast Universal Programmer","description":"\u003cp\u003eThe Xeltek SuperPro 6000E (part number SuperPro-6000E) is a 144-pin universal IC programmer that handles devices with Vcc as low as 1.2V, connects to the host over USB 2.0 High Speed and runs stand-alone from a CompactFlash card with a 20-character by 4-line LCD and 6-key keypad. Xeltek's October 2013 comparison sheet lists 83,300+ supported devices from 299 manufacturers for the 6000E, covering EPROM, EEPROM, NOR and NAND flash, PLD, NVRAM, firmware hubs and microcontrollers. It is built for production programming stations and engineering benches that program packaged parts off-board.\u003c\/p\u003e\n\n\u003ch2\u003e144-Pin Universal IC Programmer with Low-Voltage Support\u003c\/h2\u003e\n\u003cp\u003eAll 144 universal pin drivers are in the main unit, so QFP, BGA and other high pin-count packages need only a socket adapter, not a pin expander. The 6000E ships with a removable DIP48 adapter and takes CX-series socket adapters, which Xeltek lists for the SuperPro 5000\/5000E, 6000\/6000E and 5004GP. Xeltek lists adapters for DIP, SDIP, PLCC, JLCC, PGA, LGA, SOIC, SOJ, SOT, QFP, TQFP, PQFP, VQFP, MQFP, LQFP, TSOP, SOP, TSOPII, PSOP, SSOP, TSSOP, SON, EBGA, FBGA, FTBGA, VFBGA, uBGA, CSP, SCSP, QFN and HVQFN. Device support reaches down to 1.2V Vcc, and IC manufacturer approved programming algorithms are used.\u003c\/p\u003e\n\n\u003ch2\u003eStand-Alone Mode and Clustered Production Programming\u003c\/h2\u003e\n\u003cp\u003eSet up a project in PC-hosted mode, save it to a CompactFlash card, and the 6000E runs without a PC; Xeltek recommends a 256 MB card for most work. Multiple units can run concurrently as a multi-programming cluster, and Xeltek's comparison lists clustering of 15 or more units; the user guide describes four units on one hub. Over-current and over-voltage protection is built in.\u003c\/p\u003e\n\u003cp\u003eProduction mode starts the operation as soon as a chip is correctly inserted. Project files carry device selection, file loading, configuration and batch settings in one step and can be password protected for volume control.\u003c\/p\u003e\n\n\u003ch2\u003eBatch Commands, Serialisation and Logging\u003c\/h2\u003e\n\u003cp\u003eA batch command combines Program, Verify, Security and other operations in any sequence. A dynamic buffer supports per-chip data such as serial numbers, and a log file records each run for quality tracking. In-system programming is available through an optional ISP\/ICP adapter. The shared SuperPro 6000\/6000E software package (nsp6kw) runs on Windows XP, Vista, 7, 8 and 10, 32-bit and 64-bit.\u003c\/p\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003ePin drivers\u003c\/th\u003e\n\u003ctd\u003e144 universal, built in\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDevice Vcc\u003c\/th\u003e\n\u003ctd\u003eDown to 1.2V\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDevice list (Xeltek, October 2013)\u003c\/th\u003e\n\u003ctd\u003e83,300+ devices from 299 manufacturers\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDevice types\u003c\/th\u003e\n\u003ctd\u003eEPROM, paged EPROM, parallel and serial EEPROM, FPGA, PROM, flash (NOR and NAND), BPROM, NVRAM, SPLD, CPLD, EPLD, firmware hub, MCU\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePC interface\u003c\/th\u003e\n\u003ctd\u003eUSB 2.0 High Speed\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eStand-alone storage\u003c\/th\u003e\n\u003ctd\u003eCompactFlash card (256 MB recommended)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eStand-alone controls\u003c\/th\u003e\n\u003ctd\u003e20 x 4 character LCD, 6-key keypad\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eISP\/ICP\u003c\/th\u003e\n\u003ctd\u003eVia optional ISP\/ICP adapter\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eProtection\u003c\/th\u003e\n\u003ctd\u003eOver-current and over-voltage\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePower\u003c\/th\u003e\n\u003ctd\u003eAC adapter, input 100V to 240V AC, output 12V 1.5A\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eMain unit\u003c\/th\u003e\n\u003ctd\u003e216 mm (W) x 94 mm (H), 1.6 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eShipping package\u003c\/th\u003e\n\u003ctd\u003e301 x 252 x 145 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eOperating environment\u003c\/th\u003e\n\u003ctd\u003e0 to 40°C, 20% to 80% humidity\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eHost OS\u003c\/th\u003e\n\u003ctd\u003eWindows XP, Vista, 7, 8, 10 (32\/64-bit)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eLimitations\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eXeltek now lists the SuperPro 6000E in its Legacy Programmer Download Center, and its 6000E device list dates from 2013. Check every part number before ordering.\u003c\/li\u003e\n  \u003cli\u003ePackages other than 48-pin DIP need a CX-series socket adapter, ordered separately. Xeltek lists the SA series for its 48-pin-driver SuperPro programmers (the 610P and 611S, and older models including the SuperPro M), not the 6000E. The \u003ca href=\"\/it\/products\/superpro-m-low-cost-universal-programmer-xeltek-uk\"\u003eSuperPro M\u003c\/a\u003e is the only SA-compatible programmer we sell.\u003c\/li\u003e\n  \u003cli\u003eFor a larger published device list and an ARM9 MCU with Linux algorithm processing, choose the \u003ca href=\"\/it\/products\/superpro-6000-universal-programmer-xeltek-uk\"\u003eSuperPro 6000\u003c\/a\u003e.\u003c\/li\u003e\n  \u003cli\u003eFor dedicated in-system production programming over I2C, JTAG or SPI with an ATE interface, see the \u003ca href=\"\/it\/products\/xeltek-superpro-is01-in-system-programmer-uk\"\u003eSuperPro IS01\u003c\/a\u003e (\u003cspan data-ds-price=\"xeltek-superpro-is01-in-system-programmer-uk\"\u003e£1,145.84\u003c\/span\u003e).\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eSuperPro 6000E vs SuperPro 6000\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003e\u003c\/th\u003e\n\u003cth\u003eSuperPro 6000E\u003c\/th\u003e\n\u003cth\u003e\u003ca href=\"\/it\/products\/superpro-6000-universal-programmer-xeltek-uk\"\u003eSuperPro 6000\u003c\/a\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePrice (ex VAT)\u003c\/th\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"superpro-6000e-universal-programmer-xeltek-uk\"\u003e£880\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"superpro-6000-universal-programmer-xeltek-uk\"\u003e£935\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eProcessor\u003c\/th\u003e\n\u003ctd\u003e32-bit RISC MCU\u003c\/td\u003e\n\u003ctd\u003e32-bit ARM9 MCU with Linux\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePin drivers\u003c\/th\u003e\n\u003ctd\u003e144\u003c\/td\u003e\n\u003ctd\u003e144\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eXeltek device list\u003c\/th\u003e\n\u003ctd\u003e83,300+ devices from 299 manufacturers (Xeltek comparison sheet, October 2013)\u003c\/td\u003e\n\u003ctd\u003e89,932 devices from 322 manufacturers (Xeltek device list, 2014)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDevice Vcc stated by Xeltek\u003c\/th\u003e\n\u003ctd\u003eDown to 1.2V (upper limit not stated)\u003c\/td\u003e\n\u003ctd\u003e1.2V to 5V\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eStand-alone\u003c\/th\u003e\n\u003ctd\u003eCompactFlash, 20 x 4 LCD, 6-key keypad\u003c\/td\u003e\n\u003ctd\u003eCompactFlash, LCD and keypad\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eSocket adapters\u003c\/th\u003e\n\u003ctd\u003eCX series\u003c\/td\u003e\n\u003ctd\u003eCX series\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePC interface\u003c\/th\u003e\n\u003ctd\u003eUSB 2.0\u003c\/td\u003e\n\u003ctd\u003eUSB 2.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eTypical Applications\u003c\/h2\u003e\n\u003cp\u003eProduction programming of microcontrollers and NOR flash in TQFP and TSOP packages through CX adapters, with several units clustered on one line. Low-voltage serial EEPROM and flash down to 1.2V Vcc. Reprogramming CPLD, EPLD and firmware hub devices for long-life equipment, with serial numbers and a log file for traceability.\u003c\/p\u003e\n\u003cp\u003eThe SuperPro 6000E suits production engineers who need stand-alone 144-pin programming stations and test benches that program packaged devices before board assembly.\u003c\/p\u003e\n\n\u003ch2\u003eWhat's Included\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eSuperPro 6000E programmer with DIP48 adapter\u003c\/li\u003e\n  \u003cli\u003eAC adapter\u003c\/li\u003e\n  \u003cli\u003eUSB cable\u003c\/li\u003e\n  \u003cli\u003eSoftware CD\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eOrder the SuperPro 6000E from \u003cspan data-ds-price=\"superpro-6000e-universal-programmer-xeltek-uk\"\u003e£880\u003c\/span\u003e ex VAT. Send us your device part numbers and packages and we will confirm support and the CX adapter you need, or request a formal quotation. See the full \u003ca href=\"\/it\/collections\/xeltek-programmers-catalogue\"\u003eXeltek range\u003c\/a\u003e of programmers and adapters.\u003c\/p\u003e\n\n\u003cp\u003e\u003csmall\u003eLast reviewed: 30 October 2026\u003c\/small\u003e\u003c\/p\u003e\n\u003cdetails\u003e\u003csummary\u003e\u003csmall\u003eSources (3 manufacturer pages)\u003c\/small\u003e\u003c\/summary\u003e\u003cul\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.xeltek.com\/superpro-software-download-center-en-en\/legacy-programer-download-centerm\/\"\u003eXeltek: Legacy Programmer Download Center\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/pages.xeltek.com\/xeltekadaptercompatibility\/\"\u003eXeltek: SuperPro and SuperBot socket adapter compatibility\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.xeltek.com\/resources\/programmer-buying-guide\/superpro-cheat-sheet\/\"\u003eXeltek: SuperPro Cheat Sheet\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/details\u003e","brand":"Xeltek, Inc","offers":[{"title":"Default Title","offer_id":37768322580669,"sku":"SuperPro-6000E","price":880.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0522\/6931\/8333\/products\/xeltek-inc-programmer-xeltek-superpro-6000e-ultra-fast-universal-programmer-23152153460925.jpg?v=1685062190"},{"product_id":"dediprog-sf600plus-g2-spi-nor-flash-programmer","title":"Programmatore flash SPI NOR\/NAND ad alta velocità Dediprog SF600Plus-G2","description":"\u003cp\u003ePresentiamo il programmatore flash seriale NOR\/NAND SF600Plus-G2, una soluzione di programmazione veloce e versatile per sviluppatori e ingegneri. Grazie alle modalità di programmazione In-Circuit e Standalone, l'SF600Plus-G2 può aggiornare la SPI Flash saldata sulla scheda o la SPI Flash inserita nell'adattatore a zoccolo, ed è quindi la soluzione ideale per diverse esigenze di programmazione.\u003c\/p\u003e\n\n\u003ch2\u003ePassare all'SF600Plus-G2\u003c\/h2\u003e\n\n\u003cp\u003eL'SF600Plus-G2 è la versione aggiornata dei diffusi modelli SF600 e SF600Plus. Offre una maggiore efficienza di programmazione grazie all'architettura SOC su FPGA. Questo aggiornamento porta all'SF600Plus-G2 funzioni e capacità avanzate rispetto ai modelli precedenti.\u003c\/p\u003e\n\n\u003ch2\u003eSupporto SPI NAND\u003c\/h2\u003e\n\n\u003cp\u003eUna delle caratteristiche principali dell'SF600Plus-G2 è il supporto delle memorie SPI NAND. Questa funzione semplifica la programmazione per gli sviluppatori e lo distingue da altri programmatori Flash presenti sul mercato.\u003c\/p\u003e\n\n\u003ch2\u003eAlta velocità e supporto di qualsiasi capacità\u003c\/h2\u003e\n\n\u003cp\u003eL'SF600Plus-G2 supporta USB ad alta velocità e prestazioni SPI elevate. Supporta inoltre SPI Flash di qualsiasi capacità disponibile sul mercato, risultando una soluzione flessibile e pronta per il futuro.\u003c\/p\u003e\n\n\u003ch2\u003eUlteriori funzioni e capacità\u003c\/h2\u003e\n\n\u003cp\u003eL'SF600Plus-G2 offre diverse funzioni e capacità che lo rendono un programmatore potente e facile da usare. Tra queste:\u003c\/p\u003e\n\n\u003cul\u003e\n\t\u003cli\u003eSupporto per circuiti integrati a bassa tensione da 1.2V\u003c\/li\u003e\n\t\u003cli\u003ePulsante Start per la programmazione in serie quando è collegato al software\u003c\/li\u003e\n\t\u003cli\u003eProtezioni contro i conflitti di segnale\u003c\/li\u003e\n\t\u003cli\u003eFunzionalità multi-programmatore tramite USB\u003c\/li\u003e\n\t\u003cli\u003eIndice del programmatore visualizzato sul programmatore\u003c\/li\u003e\n\t\u003cli\u003eSupporto per 2 pin CS\u003c\/li\u003e\n\t\u003cli\u003eModalità Stand-Alone con programmazione tramite pulsante Start e porta di controllo per la programmazione con controllo remoto\u003c\/li\u003e\n\t\u003cli\u003eCompatibilità con WIN8 e versioni successive\u003c\/li\u003e\n\t\u003cli\u003eCompatibilità con sistemi operativi a 32 e 64 bit\u003c\/li\u003e\n\t\u003cli\u003eSupporto per die multipli Single\/Dual\u003c\/li\u003e\n\t\u003cli\u003eSupporto per IO Single\/Dual\/Quad\/Octal\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003ePassare all'SF600Plus-G2U\u003c\/h2\u003e\n\n\u003cp\u003eL'SF600Plus-G2 può inoltre essere aggiornato all'SF600Plus-G2U, che include funzioni aggiuntive come il supporto per Universal Flash Storage (UFS), un nuovo standard per memorie flash ad alta capacità e alte prestazioni.\u003c\/p\u003e","brand":"Dediprog Technology Co Ltd","offers":[{"title":"Default Title","offer_id":44008362311903,"sku":"SF600Plus-G2","price":375.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0522\/6931\/8333\/products\/dediprog-technology-co-ltd-programmer-dediprog-sf600plus-g2-spi-nor-flash-programmer-39575831380191.png?v=1684943384"},{"product_id":"segger-5-19-00-flasher-compact-programmer","title":"SEGGER Flasher Compact In-Circuit Programmer","description":"\u003cp\u003eThe SEGGER Flasher Compact (part number 5.19.00) is a universal in-system flash programmer in a 40g housing with four mounting holes, a USB-C host port, 128 MB of internal flash, a 1.2V to 5V target interface and JTAG\/SWD speeds up to 50 MHz. SEGGER describes it as functionally identical to the Flasher PRO, supporting the same devices, without the PRO's Ethernet and RS232 ports. It is built to be fixed inside production rigs, ATE and HIL fixtures, and is the programming channel used with the Flasher Hub-4 and Flasher Hub-12 for gang programming.\u003c\/p\u003e\n\n\u003ch2\u003eCompact Flash Programmer Built for ATE and Test Fixtures\u003c\/h2\u003e\n\u003cp\u003eThe four mounting holes let the Compact be screwed to a mounting plate or directly inside a fixture. It is powered from its USB-C port and needs no external supply; in stand-alone mode any standard USB power source works, such as a USB wall charger or a port on a Flasher Hub, with no data connection to a PC. It has three boot modes: PC-based, stand-alone and file-access.\u003c\/p\u003e\n\n\u003ch2\u003eGang Programming with Flasher Hub-4 and Flasher Hub-12\u003c\/h2\u003e\n\u003cp\u003eConnected to a Flasher Hub-4 or Flasher Hub-12, each Flasher Compact becomes one programming channel, and up to 24 devices can be programmed in parallel. Each channel can carry its own firmware image and settings, so different variants can run on the same line.\u003c\/p\u003e\n\n\u003ch2\u003eTarget Interfaces and Supported Devices\u003c\/h2\u003e\n\u003cp\u003eSEGGER lists tens of thousands of supported devices in hundreds of device families, and new flash loaders arrive with the free software updates. Supported target interfaces are SPI, QSPI, 8051 C2, cJTAG, FINE, ICSP, IIC, ISP, JTAG, PDI, SPD, SWD, SWIM, UART and UPDI. Supported cores include ARM Cortex-M0 to Cortex-M85, Cortex-A and Cortex-R, ARM7 and ARM9, RISC-V RV32 and RV64 and Renesas RX. Licences for all supported devices are included in the price, and devices not yet supported can be added with the Flasher SDK. The target connector is a male 20-pin IDC keyed box header with 0.1\" (2.54mm) pitch; pin assignments and adapter options are in our \u003ca href=\"\/it\/pages\/segger-j-link-20-pin-connector-pinout\"\u003eSEGGER J-Link 20-pin connector pinout\u003c\/a\u003e guide. Setup and control software runs on Windows (x86-64 and ARM64), Linux (x86-64 and ARM64) and macOS (x86-64 and Apple Silicon).\u003c\/p\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eHost interface\u003c\/th\u003e\n\u003ctd\u003eUSB 2.0 Hi-Speed, USB-C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget interface\u003c\/th\u003e\n\u003ctd\u003eMale 20-pin IDC keyed box header, 0.1\" (2.54mm) pitch, optional adapters\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eSupported target interfaces\u003c\/th\u003e\n\u003ctd\u003eSPI, QSPI, 8051 C2, cJTAG, FINE, ICSP, IIC, ISP, JTAG, PDI, SPD, SWD, SWIM, UART, UPDI\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eInternal flash memory\u003c\/th\u003e\n\u003ctd\u003e128 MB (TBW: 10 TB)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eMax. target interface speed\u003c\/th\u003e\n\u003ctd\u003eDepends on target interface; JTAG\/SWD 50 MHz\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eSupported target voltage\u003c\/th\u003e\n\u003ctd\u003e1.2V to 5V\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eCurrent drawn from VTRef\u003c\/th\u003e\n\u003ctd\u003eLess than 25µA\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget supply\u003c\/th\u003e\n\u003ctd\u003e5V, max. 400mA\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePower supply\u003c\/th\u003e\n\u003ctd\u003eUSB powered, max. 130mA idle; 500mA if the target is powered by the Flasher\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eReset type\u003c\/th\u003e\n\u003ctd\u003eOpen drain with 100 Ohm series resistor, can be pulled low or tristated\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTarget cable length\u003c\/th\u003e\n\u003ctd\u003e20cm recommended and supplied; max. 2m, which may reduce target interface speed\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eWeight (without cables)\u003c\/th\u003e\n\u003ctd\u003e40g\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eMounting\u003c\/th\u003e\n\u003ctd\u003eFour mounting holes in the housing\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eOperating temperature\u003c\/th\u003e\n\u003ctd\u003e+5°C to +60°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eStorage temperature\u003c\/th\u003e\n\u003ctd\u003e-20°C to +65°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eRelative humidity\u003c\/th\u003e\n\u003ctd\u003eLess than 90% rH, non-condensing\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eHost OS\u003c\/th\u003e\n\u003ctd\u003eWindows and Linux (x86-64, ARM64); macOS (x86-64, Apple Silicon)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eWhat's Included\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eFlasher Compact\u003c\/li\u003e\n  \u003cli\u003eUSB-C cable\u003c\/li\u003e\n  \u003cli\u003e20-pin 0.1\" target ribbon cable\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eLimitations\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eNo Ethernet or RS232. For direct network or serial control of a single programmer, choose the Flasher PRO.\u003c\/li\u003e\n  \u003cli\u003eStand-alone mode on ARM Cortex targets is limited to CoreSight SoC-400 DAP setups. Microchip PIC32, Silicon Labs EFM8 and Renesas RH850 G4KH are supported in PC-based mode only, and the Renesas FINE interface currently works in host-based mode only.\u003c\/li\u003e\n  \u003cli\u003eThe Flasher is a production programmer, not a debug probe: SEGGER lists no ETB or ETM trace, no Cortex-M monitor mode debugging and no CMSIS-DAP mode.\u003c\/li\u003e\n  \u003cli\u003eGang programming needs a Flasher Hub-4 or Flasher Hub-12, sold separately.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eFlasher Compact Compared with Other SEGGER Flasher Models\u003c\/h2\u003e\n\u003cdiv style=\"overflow-x:auto\"\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eInternal memory\u003c\/th\u003e\n\u003cth\u003eHost and control interfaces\u003c\/th\u003e\n\u003cth\u003ePower\u003c\/th\u003e\n\u003cth\u003ePrice ex VAT\u003c\/th\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eFlasher Compact (this product)\u003c\/td\u003e\n\u003ctd\u003e128 MB\u003c\/td\u003e\n\u003ctd\u003eUSB-C\u003c\/td\u003e\n\u003ctd\u003eUSB\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-5-19-00-flasher-compact-programmer\"\u003e£920\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-5-17-01-flasher-pro-programmer\"\u003eFlasher PRO\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e128 MB\u003c\/td\u003e\n\u003ctd\u003eUSB, RS232, Ethernet\u003c\/td\u003e\n\u003ctd\u003eUSB\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-5-17-01-flasher-pro-programmer\"\u003e£1,100\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-5-17-02-flasher-pro-xl-programmer\"\u003eFlasher PRO XL\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e2 GB\u003c\/td\u003e\n\u003ctd\u003eUSB, RS232, Ethernet\u003c\/td\u003e\n\u003ctd\u003eUSB\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-5-17-02-flasher-pro-xl-programmer\"\u003e£1,320\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-flasher-hub-4-control-module-5-01-30\"\u003eFlasher Hub-4\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eControl unit for up to 4 Compacts (24 with USB hubs)\u003c\/td\u003e\n\u003ctd\u003eUSB-C, Ethernet, RS232\u003c\/td\u003e\n\u003ctd\u003e8 to 30 VDC\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-flasher-hub-4-control-module-5-01-30\"\u003e£2,005\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTypical Applications\u003c\/h2\u003e\n\u003cp\u003eA programmer screwed inside a bed-of-nails fixture, flashing a Cortex-M4 MCU and its external QSPI NOR as each board is tested. Four to twenty-four Compacts on a Flasher Hub programming panels of STM32 or RISC-V boards in parallel. A HIL rig that reflashes the device under test between runs.\u003c\/p\u003e\n\u003cp\u003eChoose the Compact for fixtures and gang systems; for a single bench station with network control, the Flasher PRO carries the same programming engine.\u003c\/p\u003e\n\n\u003cp\u003eOrder the Flasher Compact for \u003cspan data-ds-price=\"segger-5-19-00-flasher-compact-programmer\"\u003e£920\u003c\/span\u003e ex VAT. Check your part number against SEGGER's supported devices list, or ask us for a formal quotation. See the full range in our \u003ca href=\"\/it\/collections\/segger-debugger-catalogue-uk\"\u003eSEGGER debug and programming tools\u003c\/a\u003e collection.\u003c\/p\u003e\n\n\u003cp\u003e\u003csmall\u003eLast reviewed 16\/11\/2026.\u003c\/small\u003e\u003c\/p\u003e\n\u003cdetails\u003e\u003csummary\u003e\u003csmall\u003eSources (4 manufacturer pages)\u003c\/small\u003e\u003c\/summary\u003e\u003cul\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/production\/flasher\/models\/flasher-compact\/\"\u003eSEGGER Flasher Compact product page\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/Flasher_Compact\"\u003eSEGGER Knowledge Base: Flasher Compact\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/Flasher_Compact_V7\"\u003eSEGGER Knowledge Base: Flasher Compact V7\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/Flasher_Hub\"\u003eSEGGER Knowledge Base: Flasher Hub\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/details\u003e","brand":"SEGGER Microcontroller GmbH","offers":[{"title":"Default Title","offer_id":44263173423327,"sku":"5.19.00","price":920.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0522\/6931\/8333\/files\/segger-microcontroller-gmbh-5-19-00-40212725399775.jpg?v=1689515404"},{"product_id":"segger-flasher-hub-4-control-module-5-01-30","title":"SEGGER Flasher Hub-4 Control Module","description":"\u003cp\u003eThe SEGGER Flasher Hub-4 (part number 5.01.30) is a gang programming control unit with four USB-C 2.0 High Speed downstream ports, each driving a Flasher Compact as an independent programming channel, scalable to 24 channels with external USB hubs. It is controlled over Ethernet, USB-C or RS232, has built-in web and FTP servers, and runs from an 8 to 30 VDC supply in a 125mm x 78mm x 25mm, 135g unit. It suits high-volume production lines that need several boards programmed in parallel without a PC on the line.\u003c\/p\u003e\n\n\u003ch2\u003eFour-Channel Gang Programmer, Scalable to 24 Channels\u003c\/h2\u003e\n\u003cp\u003eIn Direct Mode the Hub-4 manages up to four Flasher Compact modules plugged straight into its USB-C ports, with no extra USB hubs. Flex Mode connects up to 24 Flasher Compact modules through external USB hubs. SEGGER only provides technical support for setups built with SEGGER USB Hubs. Each channel works independently with its own programming image and settings, so different firmware variants can be programmed at the same time on one line. The supported CPU cores and target interfaces are those of the connected Flasher Compacts.\u003c\/p\u003e\n\n\u003ch2\u003eStand-Alone Operation via TELNET or RS232\u003c\/h2\u003e\n\u003cp\u003eChannels are set up once with SEGGER's Flasher software. After that initial configuration, the Hub-4 runs as a stand-alone unit controlled through TELNET or RS232 using the built-in ASCII command interface, which is designed for automation, so no desktop PC is needed on the line. The built-in web server handles control and configuration, and the FTP server takes new firmware images and configuration files remotely. Programming status shows on the LEDs of the connected Flashers, through the ASCII terminal interface or in the web interface. Unique data such as serial numbers, MAC addresses and digital signatures can be programmed into each target.\u003c\/p\u003e\n\n\u003ch2\u003eCompact Control Unit for Production Fixtures\u003c\/h2\u003e\n\u003cp\u003eInstead of a full chassis, the Hub-4 has a ground plate and a plexiglass cover, and SEGGER publishes housing STEP data for fixture installation. It runs from 8 to 30 VDC with reverse polarity protection; for maximum load the input supply must provide 12 VDC or more.\u003c\/p\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eUSB Flasher interface\u003c\/th\u003e\n\u003ctd\u003e4 x USB-C 2.0 High Speed (downstream)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eHost interfaces\u003c\/th\u003e\n\u003ctd\u003eUSB-C 2.0 High Speed (upstream), USB Type-A (downstream), Ethernet, RS232 9-pin\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eChannels\u003c\/th\u003e\n\u003ctd\u003eUp to 4 Flasher Compact (Direct Mode); up to 24 with USB hubs (Flex Mode)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePower supply\u003c\/th\u003e\n\u003ctd\u003e8 to 30 VDC, reverse polarity protected, max. 30 W (depends on connected devices; 12 VDC or more for maximum load)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePower consumption\u003c\/th\u003e\n\u003ctd\u003eMax. 11.5 W\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eSize (without cables)\u003c\/th\u003e\n\u003ctd\u003e125mm x 78mm x 25mm\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eWeight (without cables)\u003c\/th\u003e\n\u003ctd\u003e135g\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eConstruction\u003c\/th\u003e\n\u003ctd\u003eGround plate and plexiglass cover\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eOperating temperature\u003c\/th\u003e\n\u003ctd\u003e+5°C to +60°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eStorage temperature\u003c\/th\u003e\n\u003ctd\u003e-20°C to +65°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eRelative humidity\u003c\/th\u003e\n\u003ctd\u003eLess than 90% rH, non-condensing\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eHost OS\u003c\/th\u003e\n\u003ctd\u003eWindows and Linux (x86-64, ARM64); macOS (x86-64, Apple Silicon)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eWhat's Included\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eFlasher Hub-4\u003c\/li\u003e\n  \u003cli\u003eUSB-C cable\u003c\/li\u003e\n  \u003cli\u003ePower connector\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eLimitations\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eThe Hub-4 does not program targets itself. Each channel needs a Flasher Compact, sold separately.\u003c\/li\u003e\n  \u003cli\u003eSEGGER names only the Flasher Compact as the module the Flasher Hub controls.\u003c\/li\u003e\n  \u003cli\u003eMore than four channels need external USB hubs; SEGGER supports only setups with SEGGER USB Hubs.\u003c\/li\u003e\n  \u003cli\u003eA PC is still needed for the one-time channel configuration.\u003c\/li\u003e\n  \u003cli\u003eNo power supply unit is listed in the box, only the power connector.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eFlasher Hub-4 Compared with Related SEGGER Products\u003c\/h2\u003e\n\u003cdiv style=\"overflow-x:auto\"\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eDirect channels\u003c\/th\u003e\n\u003cth\u003eMax. channels\u003c\/th\u003e\n\u003cth\u003eSize (without cables)\u003c\/th\u003e\n\u003cth\u003ePrice ex VAT\u003c\/th\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eFlasher Hub-4 (this product)\u003c\/td\u003e\n\u003ctd\u003e4\u003c\/td\u003e\n\u003ctd\u003e24 (Flex Mode)\u003c\/td\u003e\n\u003ctd\u003e125mm x 78mm x 25mm\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-flasher-hub-4-control-module-5-01-30\"\u003e£2,005\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-flasher-hub-12-control-module-5-01-20\"\u003eFlasher Hub-12\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e12\u003c\/td\u003e\n\u003ctd\u003e24 (Flex Mode)\u003c\/td\u003e\n\u003ctd\u003eFull chassis\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-flasher-hub-12-control-module-5-01-20\"\u003e£3,005\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\n\u003ca href=\"\/it\/products\/segger-5-19-00-flasher-compact-programmer\"\u003eFlasher Compact\u003c\/a\u003e (one channel)\u003c\/td\u003e\n\u003ctd\u003en\/a\u003c\/td\u003e\n\u003ctd\u003en\/a\u003c\/td\u003e\n\u003ctd\u003e40g, four mounting holes\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-5-19-00-flasher-compact-programmer\"\u003e£920\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTypical Applications\u003c\/h2\u003e\n\u003cp\u003eFour Flasher Compacts programming a four-up panel of Cortex-M boards in one pass, triggered over TELNET from the line controller. Pushing a new release image to the hub's FTP server from a central production server without stopping the line. Writing unique serial numbers and MAC addresses into each board of a parallel run.\u003c\/p\u003e\n\u003cp\u003eChoose the Hub-4 when four parallel channels cover the line, or as a small controller for a Flex Mode system of up to 24 channels.\u003c\/p\u003e\n\n\u003cp\u003eOrder the Flasher Hub-4 for \u003cspan data-ds-price=\"segger-flasher-hub-4-control-module-5-01-30\"\u003e£2,005\u003c\/span\u003e ex VAT, plus one Flasher Compact per channel. Ask us for a formal quotation for a complete gang system. See the full range in our \u003ca href=\"\/it\/collections\/segger-debugger-catalogue-uk\"\u003eSEGGER debug and programming tools\u003c\/a\u003e collection.\u003c\/p\u003e\n\n\u003cp\u003e\u003csmall\u003eLast reviewed 16\/11\/2026.\u003c\/small\u003e\u003c\/p\u003e\n\u003cdetails\u003e\u003csummary\u003e\u003csmall\u003eSources (3 manufacturer pages)\u003c\/small\u003e\u003c\/summary\u003e\u003cul\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/production\/flasher\/tools\/flasher-hub-4\/\"\u003eSEGGER Flasher Hub-4 product page\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/Flasher_Hub\"\u003eSEGGER Knowledge Base: Flasher Hub\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/production\/flasher\/models\/flasher-compact\/\"\u003eSEGGER Flasher Compact product page\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/details\u003e","brand":"SEGGER Microcontroller GmbH","offers":[{"title":"Default Title","offer_id":44263173521631,"sku":"5.01.30","price":2005.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0522\/6931\/8333\/files\/segger-flasher-hub-4-5-01-30-perspective.png?v=1794818092"},{"product_id":"segger-flasher-hub-12-control-module-5-01-20","title":"SEGGER Flasher Hub-12 Control Module","description":"\u003cp\u003eThe SEGGER Flasher Hub-12 (part number 5.01.20) is a gang programming control unit with twelve USB-C 2.0 High Speed downstream ports, each driving a Flasher Compact as an independent programming channel, scalable to 24 channels with external USB hubs. It is controlled over Ethernet, USB or RS232, has built-in web and FTP servers, and runs from an 8 to 30 VDC supply at up to 60 W. It suits high-volume production lines programming twelve or more boards in parallel without a PC on the line.\u003c\/p\u003e\n\n\u003ch2\u003eTwelve-Channel Gang Programmer for High-Volume Production\u003c\/h2\u003e\n\u003cp\u003eIn Direct Mode the Hub-12 manages up to twelve Flasher Compact modules, each connected straight to one of its front-panel USB-C ports as a separate programming channel, with no extra USB hubs. Flex Mode connects up to 24 Flasher Compact modules through USB hubs, and each module can be assigned dynamically to any available channel. SEGGER only provides technical support for setups built with SEGGER USB Hubs. Each channel works independently with its own programming image and settings, so different firmware variants can be programmed at the same time in one setup. The supported CPU cores and target interfaces are those of the connected Flasher Compacts.\u003c\/p\u003e\n\n\u003ch2\u003eStand-Alone Operation and Production Integration\u003c\/h2\u003e\n\u003cp\u003eChannels are set up once with SEGGER's Flasher software, matched to the target flash device. A PC is needed only for that one-time configuration; the Hub-12 then runs as a stand-alone unit controlled through TELNET or RS232 using the built-in ASCII command interface. The built-in web server handles control and configuration and shows real-time status for every connected channel, and programming logs can be retrieved for production tracking and quality assurance. The FTP server takes firmware and configuration uploads and returns log files, so a central production server can push stable releases straight to the hub as part of an automated deployment pipeline. Unique data such as serial numbers, MAC addresses and digital signatures can be programmed into each target, even in parallel runs.\u003c\/p\u003e\n\n\u003ch2\u003ePower and Housing\u003c\/h2\u003e\n\u003cp\u003eThe Hub-12 has a chassis around the board with the twelve USB-C connectors on its front panel. It runs from 8 to 30 VDC with reverse polarity protection; power depends on the connected downstream devices, and for maximum load the input supply must provide 12 VDC or more.\u003c\/p\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eUSB Flasher interface\u003c\/th\u003e\n\u003ctd\u003e12 x USB-C 2.0 High Speed (downstream)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eHost interfaces\u003c\/th\u003e\n\u003ctd\u003eUSB 2.0 High Speed (upstream), USB Type-A (downstream), Ethernet, RS232 9-pin\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eChannels\u003c\/th\u003e\n\u003ctd\u003eUp to 12 Flasher Compact (Direct Mode); up to 24 with USB hubs (Flex Mode)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePower supply\u003c\/th\u003e\n\u003ctd\u003e8 to 30 VDC, reverse polarity protected, max. 60 W (depends on connected devices; 12 VDC or more for maximum load)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePower consumption\u003c\/th\u003e\n\u003ctd\u003eMax. 15 W\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eConstruction\u003c\/th\u003e\n\u003ctd\u003eChassis with 12 front-panel USB-C connectors\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eOperating temperature\u003c\/th\u003e\n\u003ctd\u003e+5°C to +60°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eStorage temperature\u003c\/th\u003e\n\u003ctd\u003e-20°C to +65°C\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eRelative humidity\u003c\/th\u003e\n\u003ctd\u003eLess than 90% rH, non-condensing\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eHost OS\u003c\/th\u003e\n\u003ctd\u003eWindows and Linux (x86-64, ARM64); macOS (x86-64, Apple Silicon)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eWhat's Included\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eFlasher Hub-12\u003c\/li\u003e\n  \u003cli\u003eUSB-C cable\u003c\/li\u003e\n  \u003cli\u003ePower connector\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eLimitations\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eThe Hub-12 does not program targets itself. Each channel needs a Flasher Compact, sold separately.\u003c\/li\u003e\n  \u003cli\u003eSEGGER names only the Flasher Compact as the module the Flasher Hub controls.\u003c\/li\u003e\n  \u003cli\u003eThe maximum is 24 channels in Flex Mode, the same as the Hub-4; Flex Mode needs external USB hubs, and SEGGER supports only setups with SEGGER USB Hubs.\u003c\/li\u003e\n  \u003cli\u003eA PC is still needed for the one-time channel configuration.\u003c\/li\u003e\n  \u003cli\u003eNo power supply unit is listed in the box, only the power connector.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eFlasher Hub-12 Compared with Related SEGGER Products\u003c\/h2\u003e\n\u003cdiv style=\"overflow-x:auto\"\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eDirect channels\u003c\/th\u003e\n\u003cth\u003eMax. channels\u003c\/th\u003e\n\u003cth\u003eMax. input power\u003c\/th\u003e\n\u003cth\u003ePrice ex VAT\u003c\/th\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003eFlasher Hub-12 (this product)\u003c\/td\u003e\n\u003ctd\u003e12\u003c\/td\u003e\n\u003ctd\u003e24 (Flex Mode)\u003c\/td\u003e\n\u003ctd\u003e60 W\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-flasher-hub-12-control-module-5-01-20\"\u003e£3,005\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/it\/products\/segger-flasher-hub-4-control-module-5-01-30\"\u003eFlasher Hub-4\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003e4\u003c\/td\u003e\n\u003ctd\u003e24 (Flex Mode)\u003c\/td\u003e\n\u003ctd\u003e30 W\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-flasher-hub-4-control-module-5-01-30\"\u003e£2,005\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003ctd\u003e\n\u003ca href=\"\/it\/products\/segger-5-19-00-flasher-compact-programmer\"\u003eFlasher Compact\u003c\/a\u003e (one channel)\u003c\/td\u003e\n\u003ctd\u003en\/a\u003c\/td\u003e\n\u003ctd\u003en\/a\u003c\/td\u003e\n\u003ctd\u003eUSB powered\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"segger-5-19-00-flasher-compact-programmer\"\u003e£920\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTypical Applications\u003c\/h2\u003e\n\u003cp\u003eTwelve Flasher Compacts programming a twelve-up panel of Cortex-M or RISC-V boards in a single pass. A line that runs two product variants side by side, with each channel carrying its own image. Release images pushed by FTP from a central build server, with per-channel logs pulled back for traceability.\u003c\/p\u003e\n\u003cp\u003eChoose the Hub-12 when the line needs more than four channels without external USB hubs; for four channels or fewer, the Hub-4 does the same job in a smaller unit.\u003c\/p\u003e\n\n\u003cp\u003eOrder the Flasher Hub-12 for \u003cspan data-ds-price=\"segger-flasher-hub-12-control-module-5-01-20\"\u003e£3,005\u003c\/span\u003e ex VAT, plus one Flasher Compact per channel. Ask us for a formal quotation for a complete gang system. See the full range in our \u003ca href=\"\/it\/collections\/segger-debugger-catalogue-uk\"\u003eSEGGER debug and programming tools\u003c\/a\u003e collection.\u003c\/p\u003e\n\n\u003cp\u003e\u003csmall\u003eLast reviewed 16\/11\/2026.\u003c\/small\u003e\u003c\/p\u003e\n\u003cdetails\u003e\u003csummary\u003e\u003csmall\u003eSources (3 manufacturer pages)\u003c\/small\u003e\u003c\/summary\u003e\u003cul\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/production\/flasher\/tools\/flasher-hub-12\/\"\u003eSEGGER Flasher Hub-12 product page\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/kb.segger.com\/Flasher_Hub\"\u003eSEGGER Knowledge Base: Flasher Hub\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.segger.com\/products\/production\/flasher\/models\/flasher-compact\/\"\u003eSEGGER Flasher Compact product page\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/details\u003e","brand":"SEGGER Microcontroller GmbH","offers":[{"title":"Default Title","offer_id":55704411996535,"sku":"5.01.20","price":3005.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0522\/6931\/8333\/files\/segger-flasher-hub-12-5-01-20-perspective.png?v=1794818092"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0522\/6931\/8333\/collections\/lg-dediprog-production-screen.jpg?v=1724338116","url":"https:\/\/thedebugstore.com\/it\/collections\/cluster-programmers.oembed","provider":"Debug Store","version":"1.0","type":"link"}