{"product_id":"test-card-set-one-port","title":"OMICRON Lab Test Card Set - One-Port","description":"\u003cp\u003eThe OMICRON Lab Test Card Set - One-Port (P0011465) is a replacement set of 32 One-Port test cards and one One-Port calibrator for the B-TCA test card adapter. The One-Port setup measures impedance or S11 reflection on a single port, with an optimal DUT impedance magnitude of 500 mΩ to 10 kΩ, within the B-TCA's recommended DC to 450 MHz range, on a Bode 500 (10 mHz to 450 MHz) or Bode 100 (1 Hz to 50 MHz) vector network analyser. It takes the largest parts of the four B-TCA setups, up to 15 mm from one contact to the other.\u003c\/p\u003e\n\n\u003ch2\u003eOne-Port Impedance and S11 From 500 mΩ to 10 kΩ\u003c\/h2\u003e\n\u003cp\u003eOn a One-Port test card the DUT is soldered between the signal pad and the GND pad, and the analyser measures the reflection from it. OMICRON Lab rates One-Port as OK for both low and high impedance: it sits between the Shunt-Thru and Series-Thru setups rather than leading at either end. Its range is limited by contact resistance and by the signal-to-noise ratio of the analyser.\u003c\/p\u003e\n\n\u003ch2\u003eOne-Port Calibrator: Open, Short and Load\u003c\/h2\u003e\n\u003cp\u003eThe black One-Port calibrator carries Open, Short and Load references, with the Load at 50 Ω. In the Bode Analyzer Suite, select User-Range or Full-Range Impedance, run Open first, then Short with the Short-Delay Time set to 0 ps, then Load. When the calibration window closes, the calibration icon turns green to show the calibration is active.\u003c\/p\u003e\n\n\u003ch2\u003eSoldering and Fitting B-TCA Test Cards\u003c\/h2\u003e\n\u003cp\u003eEach test card is a 1.57 mm (nominal) PCB for the 100-pin, 0.8 mm pitch card-edge connector of the \u003ca href=\"\/es\/products\/omicron-lab-b-tca-test-card-adapter-p0009653\"\u003eB-TCA test card adapter\u003c\/a\u003e, with the DUT soldered directly to the marked pads. Signal line contact resistance is 2 mΩ typ. with under 1 mΩ repeatability, and the connection is rated for 1,000 mating cycles. Wear gloves when breaking cards off and remove any sharp edges. Clean the contacts, then push the card straight down at its centre with under 2° of tilt.\u003c\/p\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth\u003eOrder number\u003c\/th\u003e\n\u003ctd\u003eP0011465\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eMeasurement setup\u003c\/th\u003e\n\u003ctd\u003eOne-Port (impedance or S11 reflection)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTest card colour\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eDUT connection\u003c\/th\u003e\n\u003ctd\u003eBetween signal and GND pads\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eBest-suited impedance range\u003c\/th\u003e\n\u003ctd\u003e500 mΩ to 10 kΩ (impedance magnitude)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eMax. recommended DUT size\u003c\/th\u003e\n\u003ctd\u003e15 mm contact to contact\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eCalibrator references\u003c\/th\u003e\n\u003ctd\u003eOpen, Short, Load (50 Ω)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eShort-Delay Time\u003c\/th\u003e\n\u003ctd\u003e0 ps\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eRecommended frequency range\u003c\/th\u003e\n\u003ctd\u003eDC to 450 MHz (B-TCA)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eCard thickness\u003c\/th\u003e\n\u003ctd\u003e1.57 mm (nominal)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eCard-edge connector\u003c\/th\u003e\n\u003ctd\u003e100 pins, 0.8 mm pitch\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eSignal line contact resistance (4 pins)\u003c\/th\u003e\n\u003ctd\u003e2 mΩ typ., \u0026lt; 1 mΩ repeatability typ.\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTest card ground contact resistance\u003c\/th\u003e\n\u003ctd\u003e\u0026lt; 0.5 mΩ typ., \u0026lt; 100 µΩ repeatability typ.\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTest card mating cycles\u003c\/th\u003e\n\u003ctd\u003e1,000\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eMax. voltage and current (B-TCA)\u003c\/th\u003e\n\u003ctd\u003e60 V DC, 30 V AC, 1 A\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003eB-TCA test card adapter (P0009653)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eCompatible analysers\u003c\/th\u003e\n\u003ctd\u003eBode 100, Bode 500 (via the B-TCA)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eLimitations\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003eThese are replacement parts for the \u003ca href=\"\/es\/products\/omicron-lab-b-tca-test-card-adapter-p0009653\"\u003eB-TCA test card adapter\u003c\/a\u003e. The adapter and the \u003ca href=\"\/es\/products\/omicron-lab-bode-100-vector-network-analyser-uk\"\u003eBode 100\u003c\/a\u003e or \u003ca href=\"\/es\/products\/omicron-lab-bode-500-vector-network-analyser-vna\"\u003eBode 500\u003c\/a\u003e analyser are not included.\u003c\/li\u003e\n  \u003cli\u003eB-TCA limits are 60 V DC or 30 V AC, 1 A, and under 350 mJ stored in an inductive DUT. Use only DC sources isolated from mains.\u003c\/li\u003e\n  \u003cli\u003eThe B-TCA has no internal bias-T. Above 3.3 V DC, OMICRON Lab suggests an external bias-T between the analyser and the adapter.\u003c\/li\u003e\n  \u003cli\u003eOne-Port is not the best choice at either end of the range. Below 500 mΩ choose the \u003ca href=\"\/es\/products\/test-card-set-shunt-thru\"\u003eShunt-Thru set\u003c\/a\u003e (1 mΩ to 100 Ω); above 10 kΩ choose the \u003ca href=\"\/es\/products\/test-card-set-series-thru\"\u003eSeries-Thru set\u003c\/a\u003e (1 kΩ to 1 MΩ).\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eB-TCA Test Card Set Comparison\u003c\/h2\u003e\n\u003cdiv style=\"overflow-x:auto\"\u003e\u003ctable\u003e\n  \u003ctr\u003e\n\u003cth scope=\"col\"\u003eFeature\u003c\/th\u003e\n\u003cth\u003e\u003ca href=\"\/es\/products\/omicron-lab-b-tca-test-card-adapter-p0009653\"\u003eB-TCA adapter\u003c\/a\u003e\u003c\/th\u003e\n\u003cth\u003e\u003ca href=\"\/es\/products\/test-card-set-shunt-thru\"\u003eShunt-Thru set\u003c\/a\u003e\u003c\/th\u003e\n\u003cth\u003e\u003ca href=\"\/es\/products\/test-card-set-series-thru\"\u003eSeries-Thru set\u003c\/a\u003e\u003c\/th\u003e\n\u003cth\u003eOne-Port set\u003c\/th\u003e\n\u003cth\u003e\u003ca href=\"\/es\/products\/test-card-set-shunt-thru-with-rs\"\u003eShunt-Thru with Rs set\u003c\/a\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eOrder number\u003c\/th\u003e\n\u003ctd\u003eP0009653\u003c\/td\u003e\n\u003ctd\u003eP0011462\u003c\/td\u003e\n\u003ctd\u003eP0011464\u003c\/td\u003e\n\u003ctd\u003eP0011465\u003c\/td\u003e\n\u003ctd\u003eP0011466\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eContents\u003c\/th\u003e\n\u003ctd\u003eAdapter, 2 N-N and 2 N-BNC cables, 4 calibrators, 32 test cards (8 per setup)\u003c\/td\u003e\n\u003ctd\u003e32 test cards, 1 calibrator\u003c\/td\u003e\n\u003ctd\u003e32 test cards, 1 calibrator\u003c\/td\u003e\n\u003ctd\u003e32 test cards, 1 calibrator\u003c\/td\u003e\n\u003ctd\u003e32 test cards, 1 calibrator\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eTest card colour\u003c\/th\u003e\n\u003ctd\u003eAll four\u003c\/td\u003e\n\u003ctd\u003eBlue\u003c\/td\u003e\n\u003ctd\u003eRed\u003c\/td\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003ctd\u003eGreen\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eBest-suited impedance range\u003c\/th\u003e\n\u003ctd\u003eMilliohms to megohms across four setups\u003c\/td\u003e\n\u003ctd\u003e1 mΩ to 100 Ω\u003c\/td\u003e\n\u003ctd\u003e1 kΩ to 1 MΩ\u003c\/td\u003e\n\u003ctd\u003e500 mΩ to 10 kΩ\u003c\/td\u003e\n\u003ctd\u003eSet by Rs: 1 mΩ to 100 Ω (0 Ω) up to 20 mΩ to 4,500 Ω (950 Ω)\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eMax. recommended DUT size\u003c\/th\u003e\n\u003ctd\u003ePer setup\u003c\/td\u003e\n\u003ctd\u003e≈ 9 mm contact to contact, 10 mm wide\u003c\/td\u003e\n\u003ctd\u003e≈ 9 mm contact to contact\u003c\/td\u003e\n\u003ctd\u003e15 mm contact to contact\u003c\/td\u003e\n\u003ctd\u003e≈ 9 mm x 9 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003eShort-Delay Time\u003c\/th\u003e\n\u003ctd\u003ePer setup\u003c\/td\u003e\n\u003ctd\u003e23 ps\u003c\/td\u003e\n\u003ctd\u003e0 ps\u003c\/td\u003e\n\u003ctd\u003e0 ps\u003c\/td\u003e\n\u003ctd\u003e23 ps\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003ctr\u003e\n\u003cth\u003ePrice\u003c\/th\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"omicron-lab-b-tca-test-card-adapter-p0009653\"\u003e£950\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"test-card-set-shunt-thru\"\u003e£175\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"test-card-set-series-thru\"\u003e£165.02\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"test-card-set-one-port\"\u003e£175\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan data-ds-price=\"test-card-set-shunt-thru-with-rs\"\u003e£175\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003c\/div\u003e\n\n\u003ch2\u003eTypical Applications\u003c\/h2\u003e\n\u003cp\u003eImpedance or S11 reflection against frequency, up to 450 MHz, of SMD parts whose impedance magnitude sits between 500 mΩ and 10 kΩ. Measurements on larger SMD parts, up to 15 mm contact to contact, that will not fit the 9 mm limit of the two-port cards.\u003c\/p\u003e\n\u003cp\u003eThis set suits engineers who already run a B-TCA and have used up the eight One-Port cards supplied with it.\u003c\/p\u003e\n\n\u003ch2\u003eWhat's Included\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003e32 One-Port test cards (4 × 8)\u003c\/li\u003e\n  \u003cli\u003e1 One-Port calibrator\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eThe OMICRON Lab Test Card Set - One-Port is \u003cspan data-ds-price=\"test-card-set-one-port\"\u003e£175\u003c\/span\u003e ex VAT. If you do not have the adapter yet, the \u003ca href=\"\/es\/products\/omicron-lab-b-tca-test-card-adapter-p0009653\"\u003eB-TCA\u003c\/a\u003e ships with eight cards and a calibrator per setup; contact us for a formal quotation.\u003c\/p\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003ch3\u003eWhat Is the Largest Component the One-Port Card Takes?\u003c\/h3\u003e\n\u003cp\u003eOMICRON Lab recommends a maximum DUT size of 15 mm from one contact to the other. The Series-Thru and Shunt-Thru cards are limited to about 9 mm, so One-Port is the setup for longer SMD parts.\u003c\/p\u003e\n\u003cp\u003e\u003csmall\u003eAnswered by John Legg, Director, Debug Store\u003c\/small\u003e\u003c\/p\u003e\n\u003ch3\u003eWhen Should I Use a Two-Port Setup Instead?\u003c\/h3\u003e\n\u003cp\u003eWhen the DUT impedance is below 500 mΩ or above 10 kΩ. Shunt-Thru is rated best for low impedance (1 mΩ to 100 Ω) and Series-Thru best for high impedance (1 kΩ to 1 MΩ); One-Port is rated OK at both ends.\u003c\/p\u003e\n\u003cp\u003e\u003csmall\u003eAnswered by John Legg, Director, Debug Store\u003c\/small\u003e\u003c\/p\u003e\n\n\u003cp\u003e\u003csmall\u003eLast reviewed: 18 November 2026\u003c\/small\u003e\u003c\/p\u003e\n\u003cdetails\u003e\u003csummary\u003e\u003csmall\u003eSources (1 manufacturer page, 1 user manual)\u003c\/small\u003e\u003c\/summary\u003e\u003cul\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/www.omicron-lab.com\/products\/vector-network-analysis\/accessories\/b-tca-test-card-adapter\"\u003eOMICRON Lab B-TCA Test Card Adapter\u003c\/a\u003e\u003c\/li\u003e\n  \u003cli\u003e\u003ca href=\"https:\/\/files.thedebugstore.com\/omicron-lab\/p0009653\/omicron-lab-b-tca-test-card-adapter-user-manual.pdf\"\u003eB-TCA User Manual (ENU 1302 05 02)\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/details\u003e","brand":"OMICRON-Lab","offers":[{"title":"Default Title","offer_id":55280504602999,"sku":"P0011465","price":175.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0522\/6931\/8333\/files\/omicron-lab-test-card-set-one-port-card-set.png?v=1795011457","url":"https:\/\/thedebugstore.com\/es\/products\/test-card-set-one-port","provider":"Debug Store","version":"1.0","type":"link"}