# Title: NB IoT 2 Click Board™ ## Description: How Does The NB IoT 2 Click Board™ Work? The NB IoT 2 Click Board™ as its foundation uses the BC66-NA, a high-performance NB-IoT module with extremely low power consumption from Quectel Wireless Solutions. It is designed to communicate with the infrastructures of mobile network operators through NB-IoT radio protocols (3GPP Rel.13 and 3GPP Rel.14). It supports a broad range of frequency bands such as B1/B2/B3/B4/B5/B8/B12/B13/B17/B18/B19/B20/B25/B28/B66/B71/B85. It also provides several interfaces, UART and SPI, and protocol stacks such as UDP/TCP, MQTT, LwM2M, and others. These protocols that allow data and SMS transmission using NB technology, make this module the perfect choice for building IoT applications such as smart gas and water meters, even without the need for an external MCU unit. In order to turn ON this Click board™, the user has to press the onboard push-button labelled as PWRKEY down for a period longer at least 500ms, which represents the Ignition (Power-On) button. PWRKEY button cannot be pulled down all the time; otherwise, the module will not be able to enter into power-save mode. This feature is shown by the yellow diode labelled as CONNECT to indicate the device's Operational Status. The NB IoT 2 Click Board™ communicates with MCU using the UART interface as its default communication protocol with the option for the users to use another interface such as SPI if they want to configure the module and write the library by themselves. It supports automatic baud rate detection, operates at 115200 bps by default configuration, and is used for data transmission and exchanging AT commands with the host MCU. In addition to these features, the BC66-NA also uses two GPIO pins connected to the mikroBUS™ socket. The WUP pin routed on the INT pin of the mikroBUS™ represents the external interrupt pin used for waking up the device from a power-saving mode, while the RST pin on the mikroBUS™ socket can perform Hardware Reset function by putting this pin in a logic low state. This Click board™ also has the micro USB connector allowing the module to be powered and configured by a personal computer. Also, it has an additional header labelled as ADC IN because the BC66-NA provides a 10-bit ADC input channel to read the voltage value. The interface is available in Active mode and has to be woken up first to ensure availability in Sleep modes. The NB IoT 2 Click Board™ possesses the SMA antenna connector with an impedance of 50Ω. This Click board™ can use it to connect the appropriate antenna that Mikroe has in its offer. Besides the SMA connector, it also has a SIM card slot that provides multiple connections and interface options. This Click board™ can be operated only with a 3.3V logic voltage level and comes with a proper logic voltage level conversion performed by the appropriate voltage level translator TXB0106. The board must complete the proper logic voltage level conversion before use with MCUs with different logic levels. However, the Click board™ comes equipped with a library containing functions and an example code that can be used, as a reference, for further development. SPECIFICATIONS Type LTE IoT Applications Can be used for a wide range of IoT applications, such as smart metering, intelligent wearables, security and asset tracking, home appliances, environmental monitoring, and many more. On-board modules BC66-NA - high-performance NB-IoT module with extremely low power consumption from Quectel Wireless Solutions Key Features Ultra-low power consumption, multi-band NB-IoT module, high performance, built-in eSIM, wake-up interrupt, and more. Interface UART,USB,SPI Compatibility mikroBUS Click board size L (57.15 x 25.4 mm) Input Voltage 3.3V PINOUT DIAGRAM This table shows how the pinout on the NB IoT 2 Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns). Notes Pin Pin Notes NC 1 AN PWM 16 NC Reset RST 2 RST INT 15 WUP Wake-Up Interrupt SPI Chip Select CS 3 CS RX 14 TX UART TX SPI Clock SCK 4 SCK TX 13 RX UART RX SPI Data OUT SDO 5 MISO SCL 12 NC SPI Data IN SDI 6 MOSI SDA 11 NC Power Supply 3.3V 7 3.3V 5V 10 NC Ground GND 8 GND GND 9 GND Ground ONBOARD SETTINGS AND INDICATORS Label Name Default Description LD1 PWR - Power LED Indicator LD2 CONNECT - Status LED Indicator J2 Analog Input Unpopulated ADC Channel Connector T1 PWR - Power Button NB IOT 2 CLICK ELECTRICAL SPECIFICATIONS Description Min Typ Max Unit Supply Voltage - 3.3 - V Operating Frequency Range 698 - 2170 MHz Operating Temperature Range -35 +25 +75 °C ## Product type: Click Board ## Vendor: Mikroelektronika d.o.o. ## Tags: Click Board, IoT, LTE IoT, MikroE, Quectel, WiFi+BLE, Wireless ## Price range: 37.8 - 37.8 GBP ## Link: https://thedebugstore.com/products/mikroe-4562-nb-iot-2-click-board-uk ## Compare-at price range: 54.0 - 54.0 GBP ## Options - Title: Default Title ## Collections - [New Products](https://thedebugstore.com/a/llms/collections/new-products-debug-store) - [Mikroelektronika d.o.o. (MikroE)](https://thedebugstore.com/a/llms/collections/mikroelektronika-catalogue-uk) - [Quectel IoT Module Development Boards & Support Tools](https://thedebugstore.com/a/llms/collections/quectel-board-support) - [Wireless Interface Click Boards™](https://thedebugstore.com/a/llms/collections/wireless-interface-click-boards-catalogue) - [MikroE Click Boards™](https://thedebugstore.com/a/llms/collections/mikroe-click-boards-catalogue-uk) - [Internet of Things (IOT) Boards](https://thedebugstore.com/a/llms/collections/internet-of-things-iot-catalogue) - [LTE IoT Click Boards™](https://thedebugstore.com/a/llms/collections/lte-iot-click-boards-catalogue) - [WiFi + Bluetooth Click Boards™](https://thedebugstore.com/a/llms/collections/wifi-bluetooth-click-boards-catalogue) - [Click Boards™ Summer Sale](https://thedebugstore.com/a/llms/collections/inventory-sale) - [MikroE Sale](https://thedebugstore.com/a/llms/collections/mikroe-sale) - [MIKROE Stock](https://thedebugstore.com/a/llms/collections/mikroe-products-in-stock-sale) ## Variants - Default Title, SKU: MIKROE-4562, Available: yes, Inventory: 1 ## Metafields - title_tag: MikroE NB IoT 2 Click Board™ (MIKROE-4562) - manufacturer: Mikroelektronika d.o.o. - warranty: 12 months - backorder_label: If no stock shown above, check availability - mpn: MIKROE-4562 - description_tag: The NB IoT 2 Click Board™ is a compact add-on board that contains a compact LTE Cat NB2 module with ultra-low power consumption. This board features the BC66-NA, a high-performance, multi-band LTE Cat NB2 module with extremely low power consumption from Quectel Wireless Solutions. Available from Debug Store UK. - full_description:

How Does The NB IoT 2 Click Board™ Work?

The NB IoT 2 Click Board™ as its foundation uses the BC66-NA, a high-performance NB-IoT module with extremely low power consumption from Quectel Wireless Solutions. It is designed to communicate with the infrastructures of mobile network operators through NB-IoT radio protocols (3GPP Rel.13 and 3GPP Rel.14). It supports a broad range of frequency bands such as B1/B2/B3/B4/B5/B8/B12/B13/B17/B18/B19/B20/B25/B28/B66/B71/B85. It also provides several interfaces, UART and SPI, and protocol stacks such as UDP/TCP, MQTT, LwM2M, and others. These protocols that allow data and SMS transmission using NB technology, make this module the perfect choice for building IoT applications such as smart gas and water meters, even without the need for an external MCU unit.

NB IoT 2 Click Board™

In order to turn ON this Click board™, the user has to press the onboard push-button labelled as PWRKEY down for a period longer at least 500ms, which represents the Ignition (Power-On) button. PWRKEY button cannot be pulled down all the time; otherwise, the module will not be able to enter into power-save mode. This feature is shown by the yellow diode labelled as CONNECT to indicate the device's Operational Status.

The NB IoT 2 Click Board™ communicates with MCU using the UART interface as its default communication protocol with the option for the users to use another interface such as SPI if they want to configure the module and write the library by themselves. It supports automatic baud rate detection, operates at 115200 bps by default configuration, and is used for data transmission and exchanging AT commands with the host MCU.

In addition to these features, the BC66-NA also uses two GPIO pins connected to the mikroBUS™ socket. The WUP pin routed on the INT pin of the mikroBUS™ represents the external interrupt pin used for waking up the device from a power-saving mode, while the RST pin on the mikroBUS™ socket can perform Hardware Reset function by putting this pin in a logic low state. This Click board™ also has the micro USB connector allowing the module to be powered and configured by a personal computer. Also, it has an additional header labelled as ADC IN because the BC66-NA provides a 10-bit ADC input channel to read the voltage value. The interface is available in Active mode and has to be woken up first to ensure availability in Sleep modes.

The NB IoT 2 Click Board™ possesses the SMA antenna connector with an impedance of 50Ω. This Click board™ can use it to connect the appropriate antenna that Mikroe has in its offer. Besides the SMA connector, it also has a SIM card slot that provides multiple connections and interface options.

This Click board™ can be operated only with a 3.3V logic voltage level and comes with a proper logic voltage level conversion performed by the appropriate voltage level translator TXB0106. The board must complete the proper logic voltage level conversion before use with MCUs with different logic levels. However, the Click board™ comes equipped with a library containing functions and an example code that can be used, as a reference, for further development.

SPECIFICATIONS

Type LTE IoT
Applications Can be used for a wide range of IoT applications, such as smart metering, intelligent wearables, security and asset tracking, home appliances, environmental monitoring, and many more.
On-board modules BC66-NA - high-performance NB-IoT module with extremely low power consumption from Quectel Wireless Solutions
Key Features Ultra-low power consumption, multi-band NB-IoT module, high performance, built-in eSIM, wake-up interrupt, and more.
Interface UART,USB,SPI
Compatibility mikroBUS
Click board size L (57.15 x 25.4 mm)
Input Voltage 3.3V

PINOUT DIAGRAM

This table shows how the pinout on the NB IoT 2 Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes Pin Mikrobus logo.png Pin Notes
NC 1 AN PWM 16 NC
Reset RST 2 RST INT 15 WUP Wake-Up Interrupt
SPI Chip Select CS 3 CS RX 14 TX UART TX
SPI Clock SCK 4 SCK TX 13 RX UART RX
SPI Data OUT SDO 5 MISO SCL 12 NC
SPI Data IN SDI 6 MOSI SDA 11 NC
Power Supply 3.3V 7 3.3V 5V 10 NC
Ground GND 8 GND GND 9 GND Ground

ONBOARD SETTINGS AND INDICATORS

Label Name Default Description
LD1 PWR - Power LED Indicator
LD2 CONNECT - Status LED Indicator
J2 Analog Input Unpopulated ADC Channel Connector
T1 PWR - Power Button

NB IOT 2 CLICK ELECTRICAL SPECIFICATIONS

Description Min Typ Max Unit
Supply Voltage - 3.3 - V
Operating Frequency Range 698 - 2170 MHz
Operating Temperature Range -35 +25 +75 °C

 

- google_product_category: 2082 - examples:

Software Support

We provide a library for the NB IoT 2 Click Board™ on our LibStock page, as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Library Description

Library provides functions for sending commands to devices, and for controlling included GPIO.

Key Functions

Example Description

The application is composed of three sections :

void application_task ( )
{
 nbiot2_send_cmd( &CGATT[ 0 ] );
 Delay_ms( 5000 );
 write_buff( );
 nbiot2_send_cmd( &CEREGG[ 0 ] );
 Delay_ms( 5000 );
 write_buff( );
 nbiot2_send_cmd( &CSQ[ 0 ] );
 Delay_ms( 5000 );
 write_buff( );
}

Additional Functions :

The full application code, and ready to use projects can be found on our LibStock page.

Other mikroE Libraries used in the example:

Additional Notes and Information

Depending on the development board you are using, you may need a USB UART click, USB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.

MIKROSDK

The NB IoT 2 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.

- attachments: [{"download_file":[{"download_file":"NB IoT 2 Click Board™ Schematic"}],"download_filetype":[{"download_filetype":"pdf"}]},{"download_file":[{"download_file":"Quectel BC66-NA Multi-Band LTE Module Datasheet"}],"download_filetype":[{"download_filetype":"pdf"}]}] - condition: new - custom_product: false - mpn: MIKROE-4562 - google_product_category: Electronics - custom_label_0: Click Board - device_vendor: Quectel - device_type: BC66-NA - warranty: 12 months - brand: MikroE - manufacturer: Mikroelektronika d.o.o. - badge: - widget:

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
- target_keyword: NB IoT 2 Click Board - brands: gid://shopify/Metaobject/56256004319 - breadcrumbs: ["gid://shopify/Collection/447955239135","gid://shopify/Collection/241680580797","gid://shopify/Collection/241546166461"] - customhs_code: 847330 - detailed_description: {"type":"root","children":[{"type":"heading","level":3,"children":[{"type":"text","value":"How Does The NB IoT 2 Click Board™ Work?"}]},{"type":"paragraph","children":[{"type":"text","value":"The "},{"type":"text","value":"NB IoT 2 Click Board™","bold":true},{"type":"text","value":" as its foundation uses the BC66-NA, a high-performance NB-IoT module with extremely low power consumption from Quectel Wireless Solutions. It is designed to communicate with the infrastructures of mobile network operators through NB-IoT radio protocols (3GPP Rel.13 and 3GPP Rel.14). It supports a broad range of frequency bands such as B1/B2/B3/B4/B5/B8/B12/B13/B17/B18/B19/B20/B25/B28/B66/B71/B85. It also provides several interfaces, UART and SPI, and protocol stacks such as UDP/TCP, MQTT, LwM2M, and others. These protocols that allow data and SMS transmission using NB technology, make this module the perfect choice for building IoT applications such as smart gas and water meters, even without the need for an external MCU unit."}]},{"type":"paragraph","children":[{"type":"text","value":""}]},{"type":"paragraph","children":[{"type":"text","value":"In order to turn ON this Click board™, the user has to press the onboard push-button labelled as PWRKEY down for a period longer at least 500ms, which represents the Ignition (Power-On) button. PWRKEY button cannot be pulled down all the time; otherwise, the module will not be able to enter into power-save mode. This feature is shown by the yellow diode labelled as CONNECT to indicate the device's Operational Status."}]},{"type":"paragraph","children":[{"type":"text","value":"The "},{"type":"text","value":"NB IoT 2 Click Board™","bold":true},{"type":"text","value":" communicates with MCU using the UART interface as its default communication protocol with the option for the users to use another interface such as SPI if they want to configure the module and write the library by themselves. It supports automatic baud rate detection, operates at 115200 bps by default configuration, and is used for data transmission and exchanging AT commands with the host MCU."}]},{"type":"paragraph","children":[{"type":"text","value":"In addition to these features, the BC66-NA also uses two GPIO pins connected to the mikroBUS™ socket. The WUP pin routed on the INT pin of the mikroBUS™ represents the external interrupt pin used for waking up the device from a power-saving mode, while the RST pin on the mikroBUS™ socket can perform Hardware Reset function by putting this pin in a logic low state. This Click board™ also has the micro USB connector allowing the module to be powered and configured by a personal computer. Also, it has an additional header labelled as ADC IN because the BC66-NA provides a 10-bit ADC input channel to read the voltage value. The interface is available in Active mode and has to be woken up first to ensure availability in Sleep modes."}]},{"type":"paragraph","children":[{"type":"text","value":"The "},{"type":"text","value":"NB IoT 2 Click Board™","bold":true},{"type":"text","value":" possesses the SMA antenna connector with an impedance of 50Ω. This Click board™ can use it to connect the appropriate antenna that Mikroe has in its offer. Besides the SMA connector, it also has a SIM card slot that provides multiple connections and interface options."}]},{"type":"paragraph","children":[{"type":"text","value":"This Click board™ can be operated only with a 3.3V logic voltage level and comes with a proper logic voltage level conversion performed by the appropriate voltage level translator TXB0106. The board must complete the proper logic voltage level conversion before use with MCUs with different logic levels. However, the Click board™ comes equipped with a library containing functions and an example code that can be used, as a reference, for further development."}]},{"type":"heading","level":3,"children":[{"type":"text","value":"SPECIFICATIONS"}]},{"type":"paragraph","children":[{"type":"text","value":"Type\nLTE IoT\nApplications\nCan be used for a wide range of IoT applications, such as smart metering, intelligent wearables, security and asset tracking, home appliances, environmental monitoring, and many more.\nOn-board modules\nBC66-NA - high-performance NB-IoT module with extremely low power consumption from Quectel Wireless Solutions\nKey Features\nUltra-low power consumption, multi-band NB-IoT module, high performance, built-in eSIM, wake-up interrupt, and more.\nInterface\nUART,USB,SPI\nCompatibility\nmikroBUS\nClick board size\nL (57.15 x 25.4 mm)\nInput Voltage\n3.3V"}]},{"type":"heading","level":3,"children":[{"type":"text","value":"PINOUT DIAGRAM"}]},{"type":"paragraph","children":[{"type":"text","value":"This table shows how the pinout on the "},{"type":"text","value":"NB IoT 2 Click Board™","bold":true},{"type":"text","value":" corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns)."}]},{"type":"paragraph","children":[{"type":"text","value":"Notes\nPin\nPin\nNotes\nNC\n1\nAN\nPWM\n16\nNC\nReset\nRST\n2\nRST\nINT\n15\nWUP\nWake-Up Interrupt\nSPI Chip Select\nCS\n3\nCS\nRX\n14\nTX\nUART TX\nSPI Clock\nSCK\n4\nSCK\nTX\n13\nRX\nUART RX\nSPI Data OUT\nSDO\n5\nMISO\nSCL\n12\nNC\nSPI Data IN\nSDI\n6\nMOSI\nSDA\n11\nNC\nPower Supply\n3.3V\n7\n3.3V\n5V\n10\nNC\nGround\nGND\n8\nGND\nGND\n9\nGND\nGround"}]},{"type":"heading","level":3,"children":[{"type":"text","value":"ONBOARD SETTINGS AND INDICATORS"}]},{"type":"paragraph","children":[{"type":"text","value":"Label\nName\nDefault\nDescription\nLD1\nPWR\n-\nPower LED Indicator\nLD2\nCONNECT\n-\nStatus LED Indicator\nJ2\nAnalog Input\nUnpopulated\nADC Channel Connector\nT1\nPWR\n-\nPower Button"}]},{"type":"heading","level":3,"children":[{"type":"text","value":"NB IOT 2 CLICK ELECTRICAL SPECIFICATIONS"}]},{"type":"paragraph","children":[{"type":"text","value":"Description\nMin\nTyp\nMax\nUnit\nSupply Voltage\n-\n3.3\n-\nV\nOperating Frequency Range\n698\n-\n2170\nMHz\nOperating Temperature Range\n-35\n+25\n+75\n°C"}]},{"type":"heading","level":3,"children":[{"type":"text","value":" "}]}]} - summary:

The NB IoT 2 Click Board™ is a compact add-on board that contains a compact LTE Cat NB2 module with ultra-low power consumption. This board features the BC66-NA, a high-performance, multi-band LTE Cat NB2 module with extremely low power consumption from Quectel Wireless Solutions. It provides a flexible and scalable platform for migrating from GSM/GPRS to the NB-IoT network and supports band 71 and band 85 to accommodate more operators. It also offers external interfaces, protocol stacks (providing great convenience for your applications), and a complete range of SMS and data transmission services to meet client-side demands. This Click Board™ is suitable for a wide range of IoT applications, such as smart metering, intelligent wearables, security and asset tracking, home appliances, environmental monitoring, and many more.

The NB IoT 2 Click is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click Board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.