# Title: Load Cell 5 Click Board™ ## Description: How Does the Load Cell 5 Click Board™ Work? The Load Cell 5 Click Board™ as its foundation uses the AD7780, a pin programmable, low power, low drift 24-bit ΣΔ ADC from Analog Devices, that includes a PGA and uses an internal clock. The AD7780 typically consumes only 330μA and simplifies this weigh scale design since most of the system building blocks are already on the chip. The AD7780 has two filter options selectable via FIL pin(low state - the 16.7Hz, high state - 10Hz) and a Power-Down Mode allowing the user to switch off the power to the bridge sensor and power down the AD7780 when not converting, increasing the battery life. Since the AD7780 provides an integrated solution for weighing scales, it interfaces directly to the load cell. The only required external components, which are also on the Click board™, are filters on the analogue inputs and capacitors on the reference pins for EMC purposes. The low-level signal from the load cell is amplified by the AD7780's internal PGA programmed via the PWM pin of the mikroBUS™ socket, labelled as GN, to operate with a gain of 128 or 1. The conversions from the AD7780 are then sent to the MCU through SPI serial interface, where the digital information is converted to weight. The Load Cell 5 Click Board™ uses the 6-wire load cell configuration, which has two sense pins, ground, power supply, and two output connections. The load cell differential SENSE lines connected to the AD7780 reference inputs create a ratiometric configuration immune to low-frequency changes in the power supply excitation voltage. Those sense pins are connected to the high and low sides of the Wheatstone bridge, where voltage can be accurately measured, regardless of the voltage drop due to the wiring resistance. The AD7780 has separate analogue and digital power supply pins. The analogue and digital power supplies are independent of each other to be different, or the same, potentials achieved with the AVDD SEL jumper. This feature allows selecting the AD7780 power supply between an external power supply (2.7 - 5.25V) and logic voltage levels supplied via mikroBUS™ rails. Load Cell 5 Click communicates with MCU using a standard SPI interface with a dual-purpose DOUT/RDY line. This line can function as a regular data output pin for the SPI interface or as a data ready pin (interrupt) labelled as RDY and routed on the INT pin of the mikroBUS socket. Also, it uses the RST pin on the mikroBUS™ socket, which performs the Hardware Reset function by putting this pin in a logic low state, and a blue diode labeled as ACTIVE is used to indicate the device's Active Operational Status. The Load Cell 5 Click Board™ can operate with both 3.3V and 5V logic voltage levels selected via the VCC SEL jumper. This way, it is allowed for both 3.3V and 5V capable MCUs to properly use the I2C communication lines. However, the Click board™ comes equipped with a library containing easy-to-use functions and an example code that can be used, as a reference, for further development. SPECIFICATIONS Type Force Applications The Load Cell 5 Click Board™ be used for safety-critical and weight measurement applications. On-board modules AD7780 - pin-programmable, low power, 24-bit sigma-delta ΣΔ ADC from Analog Devices Key Features Low power consumption, pin-programmable filter response, pin-programmable reset and gain, internal bridge power-down switch, independent interface power supply, and more. Interface SPI Compatibility mikroBUS Click board size M (42.9 x 25.4 mm) PINOUT DIAGRAM This table shows how the pinout of the Load Cell 5 Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns). Notes Pin Pin Notes NC 1 AN PWM 16 GN Gain Selection Reset RST 2 RST INT 15 RDY Interrupt / Data Ready Filter Select FIL 3 CS RX 14 NC SPI Clock SCK 4 SCK TX 13 NC SPI Data OUT SDO 5 MISO SCL 12 NC NC 6 MOSI SDA 11 NC Power Supply 3.3V 7 3.3V 5V 10 5V Power Supply Ground GND 8 GND GND 9 GND Ground ONBOARD SETTINGS AND INDICATORS Label Name Default Description LD1 PWR - Power LED Indicator LD2 ACTIVE - Active State LED Indicator JP1 VCC SEL Left Logic Level Voltage Selection 3V3/5V: Left position 3V3, Right position 5V JP2 AVDD SEL Left AD7780 Supply Voltage Selection VIN/VCC: Left position VIN, Right position VCC LOAD CELL 5 CLICK ELECTRICAL SPECIFICATIONS Description Min Typ Max Unit Supply Voltage 3.3 - 5 V External Supply Voltage VIN 2.7 - 5.25 V Resolution 24 - - bits Operating Temperature Range -40 +25 +105 °C ## Product type: Click Board ## Vendor: Mikroelektronika d.o.o. ## Tags: Analog Devices, Click Board, Force, MikroE, Sensor ## Price range: 23.1 - 23.1 GBP ## Link: https://thedebugstore.com/products/mikroe-4510-load-cell-5-click-board-uk ## Compare-at price range: 33.0 - 33.0 GBP ## Options - Title: Default Title ## Collections - [New Products](https://thedebugstore.com/a/llms/collections/new-products-debug-store) - [Mikroelektronika d.o.o. (MikroE)](https://thedebugstore.com/a/llms/collections/mikroelektronika-catalogue-uk) - [Analog Devices Development Boards and Support Tools | Debug Store](https://thedebugstore.com/a/llms/collections/analog-devices-device-support-uk) - [Sensor Click Boards™](https://thedebugstore.com/a/llms/collections/sensor-click-boards-catalogue) - [MikroE Click Boards™](https://thedebugstore.com/a/llms/collections/mikroe-click-boards-catalogue-uk) - [Force Sensor Click Boards™](https://thedebugstore.com/a/llms/collections/force-sensor-click-boards-catalogue) - [Click Boards™ Summer Sale](https://thedebugstore.com/a/llms/collections/inventory-sale) - [MikroE Sale](https://thedebugstore.com/a/llms/collections/mikroe-sale) - [MIKROE Stock](https://thedebugstore.com/a/llms/collections/mikroe-products-in-stock-sale) ## Variants - Default Title, SKU: MIKROE-4510, Available: yes, Inventory: 1 ## Metafields - manufacturer: Mikroelektronika d.o.o. - warranty: 12 months - amazon_enable: TRUE - amazon_title: Load Cell 5 Click Board - amazon_product_type: computercomponent - amazon_block: FALSE - amazon_prime_enable: FALSE - amazon_search: MikroElektronika Microelectronica MIKROE-1100 - amazon_uk_currency: GBP - amazon_de_currency: EUR - amazon_fr_currency: EUR - amazon_es_currency: EUR - amazon_nl_currency: EUR - amazon_it_currency: EUR - amazon_se_curency: SEK - amazon_product_id_type: EAN - amazon_update: Update - title_tag: MikroE Load Cell 5 Click Board™ (MIKROE-4510) - backorder_label: If no stock shown above, check availability - mpn: MIKROE-4510 - description_tag: The Load Cell 5 Click Board™ is a compact add-on board that represents a weigh scale solution. This board features the AD7780, a pin-programmable, low power, 24-bit sigma-delta ΣΔ ADC from Analog Devices. Available from Debug Store UK. - full_description:

How Does the Load Cell 5 Click Board™ Work?

The Load Cell 5 Click Board™ as its foundation uses the AD7780, a pin programmable, low power, low drift 24-bit ΣΔ ADC from Analog Devices, that includes a PGA and uses an internal clock. The AD7780 typically consumes only 330μA and simplifies this weigh scale design since most of the system building blocks are already on the chip. The AD7780 has two filter options selectable via FIL pin(low state - the 16.7Hz, high state - 10Hz) and a Power-Down Mode allowing the user to switch off the power to the bridge sensor and power down the AD7780 when not converting, increasing the battery life.

Load Cell 5 Click Board™

Since the AD7780 provides an integrated solution for weighing scales, it interfaces directly to the load cell. The only required external components, which are also on the Click board™, are filters on the analogue inputs and capacitors on the reference pins for EMC purposes. The low-level signal from the load cell is amplified by the AD7780's internal PGA programmed via the PWM pin of the mikroBUS™ socket, labelled as GN, to operate with a gain of 128 or 1. The conversions from the AD7780 are then sent to the MCU through SPI serial interface, where the digital information is converted to weight.

The Load Cell 5 Click Board™ uses the 6-wire load cell configuration, which has two sense pins, ground, power supply, and two output connections. The load cell differential SENSE lines connected to the AD7780 reference inputs create a ratiometric configuration immune to low-frequency changes in the power supply excitation voltage. Those sense pins are connected to the high and low sides of the Wheatstone bridge, where voltage can be accurately measured, regardless of the voltage drop due to the wiring resistance.

The AD7780 has separate analogue and digital power supply pins. The analogue and digital power supplies are independent of each other to be different, or the same, potentials achieved with the AVDD SEL jumper. This feature allows selecting the AD7780 power supply between an external power supply (2.7 - 5.25V) and logic voltage levels supplied via mikroBUS™ rails.

Load Cell 5 Click communicates with MCU using a standard SPI interface with a dual-purpose DOUT/RDY line. This line can function as a regular data output pin for the SPI interface or as a data ready pin (interrupt) labelled as RDY and routed on the INT pin of the mikroBUS socket. Also, it uses the RST pin on the mikroBUS™ socket, which performs the Hardware Reset function by putting this pin in a logic low state, and a blue diode labeled as ACTIVE is used to indicate the device's Active Operational Status.

The Load Cell 5 Click Board™ can operate with both 3.3V and 5V logic voltage levels selected via the VCC SEL jumper. This way, it is allowed for both 3.3V and 5V capable MCUs to properly use the I2C communication lines. However, the Click board™ comes equipped with a library containing easy-to-use functions and an example code that can be used, as a reference, for further development.

SPECIFICATIONS

Type Force
Applications The Load Cell 5 Click Board™ be used for safety-critical and weight measurement applications.
On-board modules AD7780 - pin-programmable, low power, 24-bit sigma-delta ΣΔ ADC from Analog Devices
Key Features Low power consumption, pin-programmable filter response, pin-programmable reset and gain, internal bridge power-down switch, independent interface power supply, and more.
Interface SPI
Compatibility mikroBUS
Click board size M (42.9 x 25.4 mm)

PINOUT DIAGRAM

This table shows how the pinout of the Load Cell 5 Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes Pin Mikrobus logo.png Pin Notes
NC 1 AN PWM 16 GN Gain Selection
Reset RST 2 RST INT 15 RDY Interrupt / Data Ready
Filter Select FIL 3 CS RX 14 NC
SPI Clock SCK 4 SCK TX 13 NC
SPI Data OUT SDO 5 MISO SCL 12 NC
NC 6 MOSI SDA 11 NC
Power Supply 3.3V 7 3.3V 5V 10 5V Power Supply
Ground GND 8 GND GND 9 GND Ground

ONBOARD SETTINGS AND INDICATORS

Label Name Default Description
LD1 PWR - Power LED Indicator
LD2 ACTIVE - Active State LED Indicator
JP1 VCC SEL Left Logic Level Voltage Selection 3V3/5V: Left position 3V3, Right position 5V
JP2 AVDD SEL Left AD7780 Supply Voltage Selection VIN/VCC: Left position VIN, Right position VCC

LOAD CELL 5 CLICK ELECTRICAL SPECIFICATIONS

Description Min Typ Max Unit
Supply Voltage 3.3 - 5 V
External Supply Voltage VIN 2.7 - 5.25 V
Resolution 24 - - bits
Operating Temperature Range -40 +25 +105 °C

 

- google_product_category: 1801 - condition: new - custom_product: false - mpn: MIKROE-4510 - google_product_category: Electronics - custom_label_0: Click Board - attachments: [{"download_file":[{"download_file":"Load Cell 5 Click Board™ Schematic"}],"download_filetype":[{"download_filetype":"pdf"}]},{"download_file":[{"download_file":"Analog Devices AD7780 24-Bit ADC Datasheet"}],"download_filetype":[{"download_filetype":"pdf"}]}] - examples:

We provide a library for the Load Cell 5 Click Board™ as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

The package can be downloaded/installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on the mikroE Github account.

Library Description

This library contains an API for the Load Cell 5 Click Board™ driver.

Key Functions

Example Description

This library contains an API for the Load Cell 5 Click driver. The library initializes and defines the SPI bus drivers to read status and ADC data. The library also includes a function for tare, calibration and weight measurement.

The demo application is composed of two sections :

void application_task ( void ) {
 weight_val = loadcell5_get_weight( &loadcell5, &cell_data );
 log_printf(&logger, " Weight : %.2f grn", weight_val );
 Delay_ms( 1000 );
}

The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager(recommended way), downloaded from our LibStock™ or found on mikroE Github account.

Other mikroE Libraries used in the example:

Additional Notes and Information

Depending on the development board you are using, you may need a USB UART click, USB UART 2 click or RS232 click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all MikroElektronika compilers, or any other terminal application of your choice, can be used to read the message.

MIKROSDK

The Load Cell 5 Click Board™ is supported with mikroSDK - MikroElektronika Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.

- device_vendor: Analog Devices Inc. - device_type: AD7780BRUZ - warranty: 12 months - brand: MikroE - manufacturer: Mikroelektronika d.o.o. - badge: - widget:

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
- target_keyword: Load Cell 5 Click Board - brands: gid://shopify/Metaobject/56256004319 - breadcrumbs: ["gid://shopify/Collection/447955239135","gid://shopify/Collection/241680580797","gid://shopify/Collection/241545969853"] - customhs_code: 847330 - detailed_description: {"type":"root","children":[{"type":"heading","level":3,"children":[{"type":"text","value":"How Does the "},{"type":"text","value":"Load Cell 5 Click Board™","bold":true},{"type":"text","value":" Work?"}]},{"type":"paragraph","children":[{"type":"text","value":"The "},{"type":"text","value":"Load Cell 5 Click Board™","bold":true,"italic":true},{"type":"text","value":" as its foundation uses the AD7780, a pin programmable, low power, low drift 24-bit ΣΔ ADC from Analog Devices, that includes a PGA and uses an internal clock. The AD7780 typically consumes only 330μA and simplifies this weigh scale design since most of the system building blocks are already on the chip. The AD7780 has two filter options selectable via FIL pin(low state - the 16.7Hz, high state - 10Hz) and a Power-Down Mode allowing the user to switch off the power to the bridge sensor and power down the AD7780 when not converting, increasing the battery life."}]},{"type":"paragraph","children":[{"type":"text","value":""}]},{"type":"paragraph","children":[{"type":"text","value":"Since the AD7780 provides an integrated solution for weighing scales, it interfaces directly to the load cell. The only required external components, which are also on the Click board™, are filters on the analogue inputs and capacitors on the reference pins for EMC purposes. The low-level signal from the load cell is amplified by the AD7780's internal PGA programmed via the PWM pin of the mikroBUS™ socket, labelled as GN, to operate with a gain of 128 or 1. The conversions from the AD7780 are then sent to the MCU through SPI serial interface, where the digital information is converted to weight."}]},{"type":"paragraph","children":[{"type":"text","value":"The "},{"type":"text","value":"Load Cell 5 Click Board™","bold":true},{"type":"text","value":" uses the 6-wire load cell configuration, which has two sense pins, ground, power supply, and two output connections. The load cell differential SENSE lines connected to the AD7780 reference inputs create a ratiometric configuration immune to low-frequency changes in the power supply excitation voltage. Those sense pins are connected to the high and low sides of the Wheatstone bridge, where voltage can be accurately measured, regardless of the voltage drop due to the wiring resistance."}]},{"type":"paragraph","children":[{"type":"text","value":"The AD7780 has separate analogue and digital power supply pins. The analogue and digital power supplies are independent of each other to be different, or the same, potentials achieved with the AVDD SEL jumper. This feature allows selecting the AD7780 power supply between an external power supply (2.7 - 5.25V) and logic voltage levels supplied via mikroBUS™ rails."}]},{"type":"paragraph","children":[{"type":"text","value":"Load Cell 5 Click communicates with MCU using a standard SPI interface with a dual-purpose DOUT/RDY line. This line can function as a regular data output pin for the SPI interface or as a data ready pin (interrupt) labelled as RDY and routed on the INT pin of the mikroBUS socket. Also, it uses the RST pin on the mikroBUS™ socket, which performs the Hardware Reset function by putting this pin in a logic low state, and a blue diode labeled as ACTIVE is used to indicate the device's Active Operational Status."}]},{"type":"paragraph","children":[{"type":"text","value":"The "},{"type":"text","value":"Load Cell 5 Click Board™","bold":true},{"type":"text","value":" can operate with both 3.3V and 5V logic voltage levels selected via the VCC SEL jumper. This way, it is allowed for both 3.3V and 5V capable MCUs to properly use the I2C communication lines. However, the Click board™ comes equipped with a library containing easy-to-use functions and an example code that can be used, as a reference, for further development."}]},{"type":"heading","level":3,"children":[{"type":"text","value":"SPECIFICATIONS"}]},{"type":"paragraph","children":[{"type":"text","value":"Type\nForce\nApplications\nThe Load Cell 5 Click Board™ be used for safety-critical and weight measurement applications.\nOn-board modules\nAD7780 - pin-programmable, low power, 24-bit sigma-delta ΣΔ ADC from Analog Devices\nKey Features\nLow power consumption, pin-programmable filter response, pin-programmable reset and gain, internal bridge power-down switch, independent interface power supply, and more.\nInterface\nSPI\nCompatibility\nmikroBUS\nClick board size\nM (42.9 x 25.4 mm)"}]},{"type":"heading","level":3,"children":[{"type":"text","value":"PINOUT DIAGRAM"}]},{"type":"paragraph","children":[{"type":"text","value":"This table shows how the pinout of the "},{"type":"text","value":"Load Cell 5 Click Board™","bold":true},{"type":"text","value":" corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns)."}]},{"type":"paragraph","children":[{"type":"text","value":"Notes\nPin\nPin\nNotes\nNC\n1\nAN\nPWM\n16\nGN\nGain Selection\nReset\nRST\n2\nRST\nINT\n15\nRDY\nInterrupt / Data Ready\nFilter Select\nFIL\n3\nCS\nRX\n14\nNC\nSPI Clock\nSCK\n4\nSCK\nTX\n13\nNC\nSPI Data OUT\nSDO\n5\nMISO\nSCL\n12\nNC\nNC\n6\nMOSI\nSDA\n11\nNC\nPower Supply\n3.3V\n7\n3.3V\n5V\n10\n5V\nPower Supply\nGround\nGND\n8\nGND\nGND\n9\nGND\nGround"}]},{"type":"heading","level":3,"children":[{"type":"text","value":"ONBOARD SETTINGS AND INDICATORS"}]},{"type":"paragraph","children":[{"type":"text","value":"Label\nName\nDefault\nDescription\nLD1\nPWR\n-\nPower LED Indicator\nLD2\nACTIVE\n-\nActive State LED Indicator\nJP1\nVCC SEL\nLeft\nLogic Level Voltage Selection 3V3/5V: Left position 3V3, Right position 5V\nJP2\nAVDD SEL\nLeft\nAD7780 Supply Voltage Selection VIN/VCC: Left position VIN, Right position VCC"}]},{"type":"heading","level":3,"children":[{"type":"text","value":"LOAD CELL 5 CLICK ELECTRICAL SPECIFICATIONS"}]},{"type":"paragraph","children":[{"type":"text","value":"Description\nMin\nTyp\nMax\nUnit\nSupply Voltage\n3.3\n-\n5\nV\nExternal Supply Voltage VIN\n2.7\n-\n5.25\nV\nResolution\n24\n-\n-\nbits\nOperating Temperature Range\n-40\n+25\n+105\n°C"}]},{"type":"heading","level":3,"children":[{"type":"text","value":" "}]}]} - summary:

The Load Cell 5 Click Board™ is a compact add-on board representing a weigh scale solution. This board features the AD7780, a pin-programmable, low-power, 24-bit sigma-delta ΣΔ ADC from Analog Devices. It interfaces directly to the load cell, where the low-level signal from the load cell is amplified by the AD7780’s internal low noise programmable gain amplifier programmed to operate with a gain of 128 or 1. It also has a power-down mode allowing the user to switch off the power to the bridge sensor and power down the AD7780 when not converting, increasing the product battery life. This Click Board™ has many features that make it a perfect solution for safety-critical and weight measurement applications.

The Load Cell 5 Click Board™ is supported by a mikroSDK compliant library, which includes functions that simplify software development. This Click Board™ comes as a fully tested product, ready to be used on a system equipped with the mikroBUS™ socket.