The Grid-EYE Click Board™ is a 8x8 thermal array sensor-detector that carries the AMG8853 infrared array sensor from Panasonic. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target MCU over I2C interface.

Use the Grid-EYE Click Board™ to detect absolute surface temperature without any contact. Or use it to detect the movement of people and objects.

AMG8853 SENSOR FEATURES

The AMG8853 is made out of 64 individual thermal sensors. It can build an image according to the heat it detects. You don't need light to form a picture.

The AMG8853 has a built-in thermistor for suppressing ambient temperature noise.

The I2C levels and address are jumper selectable, while the AMG8853 is supplied with designated voltage.

INFRARED SENSOR

Infrared waves are outside the visible spectrum of the human eye, just like radio waves. Even though people can't see infrared waves, they can certainly feel them, in the form of heat.

Our bodies emit heat or infrared radiation, and the AMG8853 thermal array sensor can detect it.

SPECIFICATIONS

PINOUT DIAGRAM

This table shows how the pinout of the Grid-EYE Click Board™ corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

JUMPERS AND SETTINGS

BUTTONS AND LEDS

MAXIMUM RATINGS

The Grid-EYE Click Board™ is a 8x8 thermal array sensor-detector that carries the AMG8853 infrared array sensor from Panasonic.

Notes	Pin		Pin	Notes
NC	1	AN	PWM	16	NC
NC	2	RST	INT	15	INT	INT out to MCU
NC	3	CS	TX	14	NC
NC	4	SCK	RX	13	NC
NC	5	MISO	SCL	12	SCL	I2C SCK
NC	6	MOSI	SDA	11	SDA	I2C data
Power supply	+3.3V	7	3.3V	5V	10	+5V	Power supply
Ground	GND	8	GND	GND	9	GND	Ground

Designator	Name	Default Position	Default Option	Description
JP1	LOGIC SEL	Left	3.3V	Logic Level Voltage Selection, left position 3.3V, right position 5V
JP2	ADDR SEL	Right	0	I2C address selection, right 0 (0b1101 000) Left 1 (0b1101 001)

Designator	Name	Type	Description
PWR	Power	LED	Power supply LED, lights green when power is on.

Description	Min	Typ	Max	Unit
Supply Voltage (with AMG8853 module)	5	5	V
I2C Levels (JP1 select)	0	5	V
INT out (JP1 select)	0	5	V

The Click Board™ is designed to run on either 3.3V or 5V power supply. It communicates with the target MCU over I2C interface.
Use the Grid-EYE Click Board™ to detect absolute surface temperature without any contact. Or use it to detect the movement of people and objects.

Code examples for the Grid-EYE Click Board™, written for MikroElektronika hardware and compilers are available on Libstock.

CODE SNIPPET

This code converts the grid array sensor data to temperature [in C] and fills the grid array drawn on the TFT display by the appropriate color, depending on the temperature detected.

01 void main() {
02   // Initialize pins as digital I/O
03   AD1PCFG = 0xFFFF;
04   JTAGEN_bit = 0;
05 
06   // Initialize I2C2 module
07   I2C2_Init(100000);
08   Delay_ms(100);
09 
10   // Draw screen
11   DrawScreen();
12 
13   // variable declaration
14   x_start = 80;
15   element_dimension = 20;
16   j = 0;
17 
18   // Set AMG88 sensor registers
19   GridEye_WriteByte(0x00,0x00);  // Normal mode
20   GridEye_WriteByte(0x01,0x30);  // Flag reset
21   GridEye_WriteByte(0x02,0x00);  // Frame mode 10FPS
22   Delay_ms(100);                 // small delay
23 
24   GridEye_WriteByte(0x08,0x30);  // INTHL
25   GridEye_WriteByte(0x09,0x00);  // INTHH
26 
27   GridEye_WriteByte(0x0A,0x15);  // INTLL
28   GridEye_WriteByte(0x0B,0x00);  // INTLH
29 
30   GridEye_WriteByte(0x0C,0x20);  // IHYSL
31   GridEye_WriteByte(0x0D,0x00);  // IHYSH
32   Delay_ms(100);                 // small delay
33 
34   // Temperature register value
35   register_address = 0x80;
36 
37   while(1) {
38     // Reading grid temperature
39     for(i = 0; i < 64; i++) {
40       // multiply the values with 0.25 to get temperature in [C]
41       gridArray[i] = (float)GridEye_ReadWord(register_address) * 0.25L;
42       // increment register address by 2
43       register_address = register_address + 2;
44     }
45 
46     // draw grid
47     for(i = 0; i < 64; i++) {
48       // set row position
49       Set_Row_Position();
50       
51       // set color
52       color = Set_Color();
53       
54       // set grid element number
55       j++;
56       
57       // fill grid element with color
58       TFT_Set_Brush(1, 0, 1, LEFT_TO_RIGHT, color, color);
59       
60       // draw grid element
61       TFT_Rectangle(x_start + (element_dimension * (j - 1)), y_start , x_start + (element_dimension * j), y_end);
62 
63       // if more than 8 elements in the row, reset counter
64       if (j >= 8) {
65         j = 0;
66       }
67     }
68   }
69 }

The Grid-EYE Click Board™ is an 8x8 thermal array sensor-detector that carries the AMG8853 infrared array sensor from Panasonic.

The Click Board™ is designed to run on either a 3.3V or 5V power supply. It communicates with the target MCU over the I2C interface.